ErGear EGCM12 User manual

Desk Monitor Arm
Monitorarm für den Schreibtisch
Bras pour Moniteur de Bureau
Brazo de Monitor de Escritorio
Braccio per Monitor da Scrivania
Instruction Manual
Bedienungsanleitung
Manuel d'instructions
Manual de instrucciones
Manuale di istruzioni
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
[e-mail]
https://ergear.com
Rev04(A)
EGCM12
English 03-11
12-20
21-29
30-38
39-47
Deutsch
Français
Español
Italiano
WWW.
Manufacturer: BESTQI INNOVATION (HONG KONG) TECHNOLOGY CO., LIMITED
Address: FLAT/RM 185 G/F HANG WAI IND CENTRE 6 KIN TAI ST TUEN MUN NT
AMZLAB GmbH
Laubenhof 23,45326 Essen
[email protected]
THEMIS AR support ltd.
85 Great Portland St, London, United Kingdom.
[email protected]

Before getting started,
let's make sure this mount is compatible.
Is the VESA pattern
of your monitor 75 x
75mm (3” x 3” ) or
100 x 100mm (3.9” x
3.9” )?
1
Does your monitor
(including acces-
sories) weigh less
than 17.6 lbs (8kg)?
2
Tools Needed
(not included)
3
Important Safety
Information
4
NOTE
• Please carefully read all instructions before attempting installa-
tion. If you do not understand the instructions or if you have any
concerns or questions, please contact our Technical Support line
as listed above or customer service at [email protected].
• Not all hardware included in this package will be used.
• This product contains small items that may pose a choking
hazard.
• Do not use this product on desks made of particle board or
other soft woods.
• The information contained in this manual does not cover all
possible conditions or variables in relation to the installation of
this product.
W
H
Avoid potential injuries and property damage!
• DO NOT use this product for any purpose that is NOT explicitly
specified in this manual. DO NOT exceed weight capacity. We are
NOT liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
• Before starting assembly, check all parts are included and
undamaged. DO NOT use damaged or defective parts. lf you
require replacement parts, contact our Technical Support line as
listed above or customer service at [email protected].
CAUTION
17.6 lbs
8kg
Yes - Perfect!
No - This mount is NOT
compatible.
Yes - Perfect!
No - This mount is NOT
compatible.
Phillips Screwdriver Electric Drill (optional)
7/16 ” -7/8 ” (11-22mm)
Drill Bit(Optional)
WARNING
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

Large Allen Key
13/64” (5mm)
Nut
M8
Bolt
M8 x 8mm
Pole
C-Clamp Locking Plate Bottom Pad
Decorative CoverMonitor Connector
Step 1 Supplied Parts and Hardware
Step 2 Supplied Parts and Hardware
01 x 1
E1 x 2
02 x 1
F1 x 1
bx 1
ax 1
03 x 1 C1 x 1
E2 x 1
Large Allen Key
13/64” (5mm)
F1 x 1
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

Step 3 Supplied Parts and Hardware
Step 4 Supplied Parts and Hardware
Faceplate Washer
M4
Spacer
L13mm
Bolt
M4 x 30mm
Bolt
M4 x 12mm
04 x 1 Dx 4
C2 x 4
Bx 4
Ax 4
Bolt
M6 x 16mm
E3 x 1
Small Allen Key
5/32” (4mm)
F2 x 1
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

Step 1 Install the Base
Option A For C Clamp Mounting
Desktop
Applicable
Desktop Thickness:
25/64″-3 5/64″
(10-78mm)
F1
01
b
b
E1
01
02
01
a
02
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

Applicable
Desktop Thickness:
25/64″-2 11/64″ (10-55mm)
7/16
” -7/8 ”
(11-22mm)
≥2” (50mm)
NOTE:
If there is no grommet hole on your desktop, mark a hole on your desired position
(Be sure to leave 2”from the edge of the desktop). Drill a hole using a drill bit in
the diameter of 7/16”-7/8” (11-22mm).
!
Option B For Grommet Mounting
Phillips Screwdriver
(Not lncluded)
Electric Drill
(optional)
02A
a1
a3
a2
02B
E2
A1
02B
b
01
01
b
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

Step 2 Secure the Monitor Connector and Deco-
rative Cover to Pole Assembly
Slide the monitor connector [03] and decorative cover [C1] into the pole [01],
and adjust to your desired height. Then tighten the pre-assembled bolt.
Height
Adjustment
!If the head is not level, adjust according to the following
solution.
WARNING
01
04
03
F1
C1
03
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

Option A For Flat Back Monitor
Option B For Curved Back Monitor
A
D
04
B
D
C2
04
Step 3 Attach the Faceplate to the Monitor
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
UP
The hanging tab should face up.
Phillips Screwdriver
(Not lncluded)
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

Step 4 Hang the Monitor on the Mount
Hang the monitor on the monitor connector [03] using the hanging tab and
bolt [E3]. Make sure the bolt is secured before you rotate the monitor.
The monitor should adjust easily when moved, then stay in place. Adjust the
tilt tension bolt [T] if your monitor naturally tilts up or down.
Step 5 Adjustments
5-1 Tilt Adjustment
Tighten
Loosen
04
03
04
03
F2
E3
TF1
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47

5-2 Level and Swivel Adjustment
Tighten
S
Loosen Level
The TV can be swivelled. Slightly loosen the bolt [S]. Adjust TV to your desired
angle, then tighten the bolt [S]. In addition, if needed, the TV can be leveled
directly by hand.
!
F1
WARNING:
To avoid tipping, please be careful not to extend the monitor too far backward. When you
adjust the angle of the monitor, please make sure the monitor is balanced to avoid
instability of the center of gravity of the base.
!
03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46 47