ErGear EGCM5 User manual

Model: EGCM5
Monitor Desk Mount Instruction Manual
V2.0
Thank you for choosing this ErGear product! At ErGear we strive
to provide you with the best quality products and services in the
industry. Should you have any issues, please don't hesitate to
contact us.
Technical Support:
1-800-651-9525 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected](US)

IMPORTANT SAFETY INSTRUCTIONS
• Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
contact our Technical Support line at 1-800-651-9525 or customer service at
[email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• The desk must be capable of supporting five times the weight of the monitor
and mount combined.
Check the VESA Pattern of Your Monitor beforeYouBegin the
Installation
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
75 mm ≈ 3 in.
100 mm ≈ 4 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
Tool Need（Not Included）
Phillips
Screwdriver Drill(Optional) 1/2 in.(13mm) - 1 in.(25mm) Drill Bit (Optional)
01 02 03 04 05 06 07

Warning: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
Product Support line at 1-800-651-9525 or customer service at
[email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware
Arm Connector
07 (x1)
Cable Clip
09 (x2)
5/32 in.(4mm)
Small Allen Key
C (x1)
13/64 in.(5mm)
Large Allen Key
D (x1)
13/64 in.(5mm)
Large Allen Key
D (x1)
Cable Clip
06 (x1)
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Pole
01 (x1)
C Clamp Plate
02 (x1)
C Clamp Plate
03 (x1)
Bolt
M6x10mm
A (x3)
Bolt
M8x10mm
B (x2)
Supplied Parts and Hardware for Step 1
Bottom Pad
05 (x1)
φ5.2Xφ12X1.5
Washer
H (x4)
Bolt
M4x12mm
TV1 (x8)
Bolt
M4x16mm
TV2 (x8)
Bolt
M5x12mm
TV3 (x8)
Bolt
M5x16mm
TV4 (x8)
L2.5 mm
Spacer
G (x16)
M8x10mm Bolt
B (x4)
Right Swivel Arm
08b (x1)
Left Swivel Arm
08a (x1)
Supplied Hardware for Step 4
5/32 in.(4mm)
Small Allen Key
C (x1)
Supplied Hardware for Step 5
13/64 in.(5mm)
Large Allen Key
D (x1)
01 02 03 04 05 06 07

Step 1 Install the Pole to the Desktop
Option A: Desk Clamp Assembly
05
A
05
C
Small Allen
Key
03
01
B
D
02
Large
Allen Key
OR
19/32 in. - 3 5/32 in. (15-80mm) 19/32 in. - 3 5/32 in. (15-80mm)
15/32 in. - 1 31/32 in. (12-50mm) 15/32 in. - 1 31/32 in. (12-50mm)
01 02 03 04 05 06 07

D
B
08a
UP
07
08b
Option B: Grommet Base Assembly
Step 2 Secure the Swivel Arm Assembly to the Pole
If there is no grommet hole on
your desk, position the pole (01)
on the mounting surface and
mark the hole. Drill a hole using
the drill bit in a diameter of
7/16in.(11mm)-33/64in.(13mm)
at the marked position through
the mounting surface.
09
09
07
02b
02a
01
25/32 in. - 2 23/64 in. (20-60mm)
7/16 in. - 33/64 in. (11-13mm) 7/16 in. - 33/64 in. (11-13mm)
02b
02a
01 02 03 04 05 06 07

Step 3 Secure the Moitors to Swivel Arms
Alternate
Spacer
Setups
Secure 2 pcs bolts into the
top VESA holes on the back
of the monitor manually.
Please keep about 0.2 in.( 5mm)
spacing left for the two bolts.
4x4 in.(100x100mm)
TV1/TV2
TV3/TV4
3x3 in.(75x75mm)
G
(If needed)(If needed)
3 in. (75mm)x3 in. (75mm)
4 in.(100mm)x4 in.(100mm)
Phillips
Screwdriver
[Not Included]
D
Large
Allen Key
Large
Allen Key
06
0.2 in.(5mm) spacing left0.2 in.(5mm) spacing left
01 02 03 04 05 06 07

TV1/TV2
TV3/TV4
G
H
(If needed)(If needed)
HEAVY! You may need
assistance with this step.
Step 4 Adjust Monitor Position
Turn the preassembled
bolt [S] clokwise or
counter-clockwise to
adjust the monitor up
or down
D
S
Slightly Adjust the Height of the Monitor
Large
Allen Key
Large
Allen Key
01 02 03 04 05 06 07

Horizontally Shift the Monitor Along the Swivel Arm
Step 5 Cable Management and Angle Adjustment
Tilt the bottom of the monitor
forward and move the monitor
along the swivel arm.
360°
360°
C
Small Allen
Key
Small Allen
Key
Slightly loosen the set bolt
to adjust the tilt angle and
tighten set bolt to hold the
tilt angle.
Tilt Adjustment
Tilt Adjustment
01 02 03 04 05 06 07