Ergo In Demand PSD-TS User manual

9531-000-100-06
INSTALLATION INSTALLATIONS
PSD-TS
FLOOR STAND
NORTH AMERICA
Ergo In Demand, Inc.
4900 Industry Drive
Central Point, Oregon 97502 USA
Contact Information:
800.888.6024 (Toll Free)
541.779.3763 (Office)
541.779.0829 (Fax)
[email protected] (Email)
www.ergoindemand.com (Website)

PSD-TS
Page - 2 - Installation Manual
Table of Contents
Warning Statements ...........................................................................................................................................- 2 -
Parts List ............................................................................................................................................................- 3 -
Installation Tools ...............................................................................................................................................- 3 -
Features ..............................................................................................................................................................- 4 -
Support Pole Installation ....................................................................................................................................- 5 -
Adapter Installation ............................................................................................................................................- 5 -
Installing the Back Plate ....................................................................................................................................- 5 -
Attaching the Display ........................................................................................................................................- 6 -
Optional Items ....................................................................................................................................................- 7 -
Warranty ............................................................................................................................................................- 8 -
Warning Statements
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS,
DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF
OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
THE MOUNTING SURFACE MUST BE CAPABLE OF SUPPORTING 160LBS. IF NOT, THE MOUNTING SURFACE MUST
BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN
THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS
PERSONAL INJURY, OR EVEN DEATH. THE OPTIONAL SHELF IS ONLY CAPABLE OF HOLDING 25LBS. OR LESS.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE
PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND
COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE
LOCATION FOR FUTURE REFERENCE.
Indicates that the power plug is to be disconnected from the
power outlet.
Contact Ergo In Demand with any questions –
[phone].
Safety precautions must be taken at all times.
.stnemetatsnoituaCdnagninraW
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the flat
panel display and/or damage to the mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in
damage to the flat panel display and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the
flat panel display.
This stand is intended for use only with the maximum weights indicated. Use with products heavier than the maximum
weights indicated may result in instability causing possible injury.

PSD-TS
Installation Manual Page - 3 -
Parts List
This floor stand is shipped with all proper installation hardware and components. Make sure that none of these parts
are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the
installation and contact Ergo In Demand (800-888-6024).
Please review all WARNING and CAUTION statements (see Page 2) before beginning the installation of the
PSD-TS.
PSD TS Base
(Qty 1) Support Poles
(Qty 2) 84"
72"
60"
PSD-SPA
Adapter
(Qty 1)
M8 x 10mm Set
Screw
(Qty 10)
M10 x 12mm
Slotted Hex
Head (Qty 4)
M10 Flat Washers
(Qty 4)
Shelf (Optional)
NOTE: The
shelf is only
capable of
holding 25Lbs.
or less.
Installation Tools
nuGllirDteknalB/lairetaMtfoSrevirDwercSdaeHspillihP
tekcoSmm71hcnerWtekcoSlicneP
5/32” Allen Key (Supplied)
The length will vary,
depending on the order.

PSD-TS
Page 4 Installation Manual
Features
Congratulations on the purchase of your new PSD-TS Floor Stand. When combined with a mount, our floor stand allows you to
place a display in a horizontal or vertical position (with the PSM mount only). The floor stand can be configured for single flat
panel display. The height is adjustable to any point along the stand’s vertical support poles to achieve the perfect viewing
level. The PSD-TS mates directly to our CTM orPSM series of mounts.
PSM Series Mount CTM Series Mount
PSD-TS
Base
PSD-TS
Base
PSD-TS
Base
PSD-SPA
Adapter
Optional PSM
Mount
Optional
CTM Mount

PSD-TS
Installation Manual Page 5
Support Pole Installation
Remove the stand out of the box and check for all proper
hardware, if missing any hardwareplease call Ergo In Demand.
A PSM or CTM series mount is required to complete
the PSD-TS system. Refer to the installation
instructions to install the mounting bracket.
1. Insert the poles inside the base columns of the PSD-TS,
making sure they are fully seated on the base with the
cable access holes facing the rear of the base.
2. Secure the poles with four (4) M8 x 10mm socket
head screws and tighten them using the Allen wrench
(supplied).
3. Do not over tighten the screws.
Adapter Installation
1. Install the PSD-SPA (mount adapter) over the top of the
poles and secure it at the desiredheight with the four (4)
M8 x 10 Allen screws (supplied).
2. Use the Allen wrench (supplied) to secure the adapter to the
poles.
Installing the Back Plate
The back plate will vary depending on the system
ordered. There are two (2) different systems for this
stand: the PSM series and the CTM series.
Arrow must be pointing up prior to installation.
Secure the following plates to the secured
PSD-SPA on the tubes.
1. For the PSM-Series, secure the back plate to the four (4)
threaded mounting points found on the PSD-SPA with the
four (4) M10 x 12 bolts and flat washers (supplied).
2. For the CTM-Series, secure the back plate to the four (4)
threaded mounting points found on the PSD-SPA with the
four (4) M10 x 12 bolts and flat washers (supplied).
2” Support
Poles
PSD-TS
Collared
Mounting
Columns
Allen Wrench
M8 x 10mm
Hex screws
PSD-SPA
Ada
p
te
r
2” Support
Poles
CTM Back
Plate
M10 x 12mm
Hex Head Bolts
Flat Washers
Back Plate
PSD-SPA
Adapter
Allen
Wrench
M8 x 10mm
Hex screws
Directional
Arrow

PSD-TS
Page 6 Installation Manual
Attaching the Display
This stand is intended for use only with the maximum
weights indicated. Use with products heavier than the
maximum weights indicated may result in instability
causing possible injury.
The flat panel display is very heavy; two people are
required to lift the flat panel and secure it to the
stand.
To install the PSM-series or CTM-series mounting
brackets to the flat panel, refer to its installation
instructions.
The diagrams (to the right) show the CTM and PCM series
systems.
PSM-Series: Raise the flat panel display with the mounting
bracket secured and insert the four (4) tab
openings from the PSM mount to the four (4)
receiving tabs found on the back plate
Push the flat panel display down, right and
down again to lock the mount together.
Make sure all tab openings are interlocked with
the receiving tabs before letting go of the flat
panel.
Secure the brackets with two (2) M6 x 12mm
Phillips (supplied) screws for additional security.
Raise the flat panel display with the left and right
brackets secured to the plasma and insert the
bottom and top hooks from the mounting arms to
the top and bottom rods found on the CTM back
plate. Secure the mounting arms with the two (2)
M6 x 12mm Safety knobs (supplied).
The safety knobs MUST be used. Failure to do so
may result in damage to the flat panel display or
personal injury.
CTM
Series
PSM
Series
PSM Back
Plat
e
PSM
Mounting
Bracket
Flat Panel
PSD-TS
Base
CTM Back
Plat
e
M6 x 12mm
Safety Knobs
CTM Series
Mounting
Brackets
Flat Panel
PSD-TS
Base
M6 x 12mm
Security
Screws
1
2
3

PSD-TS
Installation Manual Page - 7 -
Optional Items
noitallatsnIroolF
1. If securing the base to the floor, use (commercially
available) hardware.
noitallatsnIflehS
Do not install the optional shelf higher than 39”.
If using a shelf, please install prior to attaching the
display.
1. The shelf must be attached before the flat paneldisplay and
PSD-SPA adapter is installed to the stand.
2. Install the shelf to the poles by sliding the shelf over the
poles and down into position.
3. Determine the final height and secure the shelf using four (4)
M8 x 10mm set screws.
4. Tighten these screwsusing the supplied Allen wrench.
Suitable
Hardware
(Commercially
Available
)
PSD-TS
Optional
Shelf
PSD-TS
M8 x 10mm
Set Screw

PSD-TS
Page - 8 - Installation Manual
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS,
DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN
WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE
OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS
PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS
OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original
consumer purchaser must accompany all warranty claims. Warranty claims must also include a description of
the problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to
Premier Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or
by fax.
Premier Mounts
Attn: Warranty Claim
3130 E. Miraloma Avenue
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.