ERIK NELSON ENTERTAINMENT Diamond Pro Venue 600 User manual

1
User Manual
Diamond Pro Venue 600
Hybrid Beam/Spot/Wash

2
Table of Contents
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fixture Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DMX Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Technical Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Gobo Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3
DISCLAIMER
©2020 Erik Nelson Entertainment all rights reserved. Information, specifications, diagrams, images, and
instructions herein are subject to change without notice. Erik Nelson Entertainment’s logo and
identifying product names and numbers herein are trademarks of Erik Nelson Entertainment. Copyright
protection claimed includes all forms and matters of copyrightable materials and information now
allowed by statutory or judicial law or hereinafter granted. Product names used in this document may
be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All
non-Erik Nelson Entertainment brands and product names are trademarks or registered trademarks of
their respective companies.
Erik Nelson Entertainment and all affiliated companies hereby disclaim any and all liabilities for
property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect
economic loss associated with the use or reliance of any information contained within this document,
and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and
operation of this product. Copyright © 2020 by Erik Nelson Entertainment
No part of this publication may be reproduced, distributed, or transmitted in any form or by any means,
including photocopying, recording, or other electronic or mechanical methods, without the prior written
permission of the publisher. For permission requests, write to the publisher, addressed “Attention:
Permissions Coordinator,” at the address below.
Erik Nelson Entertainment | 2201 Franscisco Blvd Ste 140-461, El Dorado Hills, CA 95762
1-800-457-8084 | www.prolightingsound.com

4
Introduction
Please read and understand the instructions in this manual before attempting to operate this
device. These instructions contain important safety and use information.
Unpacking
Carefully inspect the shipping package for damage that may have occurred during shipping. If
the packaging is damaged, carefully inspect the device for damage, and be sure all accessories
needed for operation and installation of the device have arrived intact. If damage has been
found or parts are missing, please contact our customer support team for assistance. Please
recycle the shipping package whenever possible.
Shipping Contents
In the shipping package there should be:
•Diamond Pro Venue 600
•Omega Bracket x2
•Safety Cable
•True1 Power Cable
•Ethernet Cable
•User Manual
Customer Support
Erik Nelson Entertainment | 2201 Franscisco Blvd Ste 140-461, El Dorado Hills, CA 95762
1-800-457-8084 | www.prolightingsound.com

5
Warranty Returns
To obtain warranty service, please reach out to ENE Customer Support. It is the Customer’s
responsibility to provide proof of purchase and serial number if applicable, and any relevant
maintenance records at the time warranty service is requested. Accepted forms of proof can be
an invoice copy or an ENE Warranty Certificate. Failure to provide sufficient evidence of proof of
purchase or Warranty Certificate and any relevant maintenance records may be cause for denial
of warranty service.
Products returned for warranty service must be sent without any accessories (i.e., power, data,
safety cables, brackets, clamps, etc.), must be boxed using the original or suitable packaging
materials (double-box and foam) that provides protection for ground and/or air freight transit. A
brief description of the problem and Customer information (i.e., name, company, address,
phone number.) must be documented and included in the box.
Products returned for warranty service without Customer information and a description of the
problem will be refused and returned at the Customer’s expense. Products returned for
warranty service, which are received damaged due to inadequate and/or improper packaging,
may incur additional repair charges before warranty service begins or may void this warranty. If
any product accessories are shipped with the product, they will not be returned to the
Customer. If the requested warranty repairs or service (including parts replacement) are within
the terms of this warranty, Erik Nelson Entertainment will pay for return ground shipping within
the United States.
Customer Support
Erik Nelson Entertainment | 2201 Franscisco Blvd Ste 140-461, El Dorado Hills, CA 95762
1-800-457-8084 | www.prolightingsound.com

6
Safety Guidelines
This fixture is a sophisticated piece of electronic equipment. To guarantee a smooth operation,
it is important to follow all instructions and guidelines in this manual. After you have become
familiar with this manual, we recommend that you keep a copy for future reference. Erik Nelson
Entertainment is not responsible for injury or damages resulting from the misuse of this fixture.
Only qualified personnel should perform installation and maintenance of this fixture and only
the original omega brackets included with this fixture should be used for installation.
Modifications to the fixture or the included mounting hardware will void the original
manufactures warranty and increase the risk of damage or personal injury.
PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED
DO NOT PLUG FIXTURE INTO A DIMMER PACK
NEVER OPEN FIXTURE WHILE IN USE
UNPLUG POWER BEFORE SERVICING FIXTURE
NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT! KEEP FLAMMABLE MATERIALS
AWAY FROM FIXTURE
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE RETINA INJURY RISK - MAY INDUCE BLINDNESS
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK
INDOOR / DRY LOCATIONS USE ONLY
DO NOT EXPOSE FIXTURE TO RAIN AND MOISTURE
MINIMUM DISTANCE TO OBJECTS/SURFACES MUST BE 13.1 FEET (4 METERS)
MINIMUM DISTANCE OF INFLAMMABLE MATERIALS FROM THE SURFACE 1.6 FEET (0.5 METER)

7
Safety Guidelines Cont.
DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow 10 minutes
for the fixture to cool down before servicing.
DO NOT shake fixture, avoid brute force when installing or operating fixture.
DO NOT operate fixture if the power cord is frayed, crimped, or damaged.
NEVER force a power cord connector into the fixture. If the power cord or any of its connectors
are damaged, replace it immediately with a new one of equal or greater power rating.
DO NOT block any air vents.
All fan and air intakes must remain clean and unobstructed.
Allow 6” (15cm) on all sides of fixture for proper cooling.
Always disconnect fixture from power source before performing any type of service and/or
cleaning procedure.
During the initial operation of this fixture, a light smoke or smell may emit from the interior of
the fixture. This is a normal process and is caused by excess paint in the interior of the casing
burning off from the heat associated with the lamp and will decrease gradually over time.
Consistent operational breaks ensure fixture will function properly for many years.
Condensation may form on the fixture In places with fog or a high level of humidity or when the
fixture is suddenly moved from a cold to a warm environment, or vice versa. In such cases, you
must wait for the fixture to fully adjust to the ambient temperature of the room where it will be
installed for operation.

8
Maintenance Guidelines
DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
Cleaning
Frequent cleaning is recommended to ensure proper function, optimized light output, and an
extended life. Clean the external lens surface at least once a month with a soft cloth to avoid
dirt/debris accumulation. The frequency of cleaning depends on the environment in which the
fixture operates: damp, smoky or particularly dirty environments can cause greater
accumulation of dirt on the fixture’s optics and may require more frequent cleaning.
NEVER use alcohol, solvents, or ammonia-based cleaners.
Inspection
Regular inspections are recommended to ensure proper function and extended life.
Please refer to the following points during routine inspections:
Be sure all screws and fasteners are securely tightened.
Check for any deformations on the housing, color lenses, rigging hardware and rigging points
(ceiling, suspension, trussing).
Electric power supply cables must not show any damage, material fatigue or sediments. NEVER
remove the ground prong from the power cable.
If any defects are found with the fixture, it should be removed from service immediately until it
can be repaired by a qualified technician.

9
Error Messages
When you turn on the fixture, it will first perform an automatic reset where it calibrates all of its
channel functions. The display may show “Err channel is XX” indicating there is a problem with
one or more of the channels.
1. If there is an error on channel 1 and channel 3 at the same time, the following error message
may appear: “Err channel is Pan movement”, “Err channel is Tilt movement.” The system will
flash twice, and the fixture will start a second reset. If the error message persists after more
than two resets, the channels showing errors will not work properly but the other channels will
function normally.
PAN- movement Er
(PAN-yoke movement error): This message will appear after the reset if the yoke’s magnetic-
indexing circuit malfunctions (failed sensor or magnet missing) or the stepping-motor is
defective (also caused by its driving IC on the main PCB). The PAN- movement does not return to
the default position after the reset.
TILT- movement Er
(TILT-head movement error): This message will appear after the reset if the head’s magnetic-
indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is
defective (also caused by its driving IC on the main PCB). The TILT- movement does not return to
the default position after the reset.

10
Fixture Dimensions

11
DMX Chart
Value Function Value Function
34CH 54CH 34CH 54CH
Pan Color Wheel Fine
0-255 Pan Movement 0-255 Color Wheel Fine
Pan Fine Cyan
0-255 Pan Fine Movement 0-255 Cyan Color 0% - 100%
Tilt Cyan Fine
0-255 Tilt Movement 0-255 Cyan Fine Color 0% - 100%
Tilt Fine Magenta
0-255 Tilt Fine Movement 0-255 Magenta Color 0% - 100%
Pan / Tilt Speed Magenta Fine
0-255 P/T Speed Max to Min 0-255 Magenta FIne Color 0% - 100%
Shutter, Strobe Yellow
0-31 Shutter Closed 0-255 Yellow Color 0% - 100%
32-63 Shutter Open Yellow Fine
64-95 Strobe Effect Slow to Fast 0-255 Yellow Fine Color 0% - 100%
96-127 Shutter Open CTO
128-159 Pulse Effects 0-255 CTO Color 0% - 100%
160-191 Shutter Open CTO Fine
192-223 Random Strobe Effect Slow to Fast 0-255 CTO Fine Color 0% - 100%
224-255 Shutter Open Rotating Gobo Wheel
Dimmer 0-21 Open
0-255 Dimmer 0% - 100% 22-35 Rotating Gobo 1
Dimmer Fine 36-49 Rotating Gobo 2
0-255 Dimmer Fine 0% - 100% 50-63 Rotating Gobo 3
Zoom 64-77 Rotating Gobo 4
0-255 Zoom Small to Big 78-91 Rotating Gobo 5
Zoom Fine 92-105 Rotating Gobo 6
0-255 Zoom Fine Small to Big 106-119 Gobo 1 Shake Slow to Fast
Focus 120-133 Gobo 2 Shake Slow to Fast
0-255 Focus Near to Far 134-147 Gobo 3 Shake Slow to Fast
Focus Fine 148-161 Gobo 4 Shake Slow to Fast
0-255 Focus Fine Near to Far 162-175 Gobo 5 Shake Slow to Fast
Dummy Channel 176-189 Gobo 6 Shake Slow to Fast
0-255 190-221 Forward Rotate Fast to Slow
Dummy Channel 222-223 No Rotate
0-255 224-255 Backward Rotate Slow to Fast
Color Wheel Rotating Gobo Index
0-15 Open 0-127 Gobo Indexing
16-22 Open / Color 1 128-189 Forward Rotate Fast to Slow
23-29 Color 1 190-193 No Rotate
30-36 Color 1 / Color 2 194-255 Backward Rotate Slow to Fast
37-43 Color 2 Rotating Gobo Index Fine
44-50 Color 2 / Color 3 0-255 Fine Indexing
51-57 Color 3
58-64 Color 3/ Color 4
65-71 Color 4
72-78 Color 4 / Color 5
79-85 Color 5
86-92 Color 5 / Color 6
93-99 Color 6
100-106 Color 6 / Color 7
107-113 Color 7
114-120 Color 7 / Open
121-127 Open
128-189 Forward Rotate Fast to Slow
190-193 No Rotate
194-255 Backward Rotate Slow to Fast
Mode
1
1
2
2
DMX Channel List - Diamond Pro Venue 600
18
26
17
25
13
17
18
14
19
6
6
7
7
8
3
3
4
4
5
5
12
10
13
11
14
8
9
10
9
11
27
20
12
15
16
24
15
21
22
16
23
Mode

12
DMX Chart Cont.
Value Function Value Function
34CH 54CH 34CH 54CH
Fixed Gobo Blade 1A
0-13 Open 0-255 Open to Close
14-24 Gobo 1 Blade 1A Fine
25-35 Gobo 2 0-255 Open to Close Fine
36-46 Gobo 3 Blade 1B
47-57 Gobo 4 0-255 Open to Close
58-68 Gobo 5 Blade 1B Fine
69-79 Gobo 6 0-255 Open to Close Fine
80-90 Gobo 7 Blade 2A
91-101 Gobo 8 0-255 Open to Close
102-112 Gobo 1 Shake Slow to Fast Blade 2A Fine
113-123 Gobo 2 Shake Slow to Fast 0-255 Open to Close Fine
124-134 Gobo 3 Shake Slow to Fast Blade 2B
135-145 Gobo 4 Shake Slow to Fast 0-255 Open to Close
146-156 Gobo 5 Shake Slow to Fast Blade 2B Fine
157-167 Gobo 6 Shake Slow to Fast 0-255 Open to Close Fine
168-178 Gobo 7 Shake Slow to Fast Blade 3A
179-189 Gobo 8 Shake Slow to Fast 0-255 Open to Close
190-221 Forward Rotate Fast to Slow Blade 3A Fine
222-223 No Rotate 0-255 Open to Close Fine
224-255 Backward Rotate Slow to Fast Blade 3B
Animation Wheel 0-255 Open to Close
0-127 Animation Indexing Blade 3B Fine
128-189 Forward Rotate Fast to Slow 0-255 Open to Close Fine
190-193 No Rotate Blade 4A
194-255 Backward Rotate Slow to Fast 0-255 Open to Close
Iris Blade 4A Fine
0-255 Iris Max to Min 0-255 Open to Close Fine
Iris Fine Blade 4B
0-255 Iris Fine Max to Min 0-255 Open to Close
Prism Blade 4B Fine
0-127 Open 0-255 Open to Close Fine
128-255 Prism All Blade Rotate
Prism Rotate 0-255 All Bkade Rotate
0-127 Prism Indexing All Blade Rotate Fine
128-189 Forward Rotate Fast to Slow 0-255 All Blade Rotate
190-193 No Rotate Control
194-255 Backward Rotate Slow to Fast 0-9 Unused
34 Prism Rotate Fine 10-19 Display Off
0-255 Prism Rotate Fine 20-29 Display On
Frost 30-39 Display Invert Off
0-127 Open 40-49 Display Invert On
128-255 Frost 50-59 Auto Fan Mode
60-69 High Fan Mode
70-79 Silent Fan Mode
80-89 Square Law
90-99 Linear
100-149 Unused
150-159 All Motor Reset
160-169 Scan Motor Reset
170-179 Color Motor Reset
180-189 Gobo Motor Reset
190-199 Other Motor Reset
200-255 Unused
DMX Channel List - Diamond Pro Venue 600
Mode
Mode
50
45
30
46
47
24
35
34
54
19
28
20
29
21
30
31
51
33
52
53
31
48
49
32
43
29
44
27
40
41
28
42
25
36
37
38
39
26
22
23
32
33

13
Technical Information
Optics
Lamp: 600W White LED
CT: 6500K
Life: 20,000H
CRI：≥74
Power
Max power consumption: 850W Pf ≥0.98
Power supply: Electronic auto-ranging
Input voltage range: 100–240V, 50-60Hz
Movement
Pan movement: 540° (16bit )
Tilt movement: 270° (16 bit)
Colors
CMY color mixing
CTO linear 2700K~6500K
1 Color wheel: 7 dichroic filters +open
Gobos
1 Rotating gobo wheel: 6 interchangeable +open
1 Static gobo wheel: 7 + open
Features
Rotating prism: 5-facet prism
Focus : motorized focus
Shutter: electronic, variable from 1-25Hz or random
Dimming: 0-100% linear dimming
Frost
Zoom: 7°-42° linear zoom
Animation wheel: special dynamic flame or water effect, etc
Framing system: with 4 independent blades with assembly rotation of ±45°
Display
LCD touch display
15 second standby auto lock
Pan/ Tilt disengage (hold MENU and ENTER button)
Software
2 Control channel modes: 34/54 channels
ArtNET control
RDM compatible
Dimensions and weight
Body size: 290x390x740mm
Net weight:30kg

14
Gobo Images
Static Gobo Wheel
Rotating Gobo Wheel
Animation Wheel