ESCALADE WOODPLAY PG122W User manual

817 Maxwell Avenue• Evansville, IN 47711 •1- 800-GO-SWING •www.escaladesports.com • © 2016 Escalade Sports
PG-MA-0020-03
TIGER TOWER
PG122W
REQUIRED TOOLS:
(2) 3/4" Sockets and Ratchets
3/4" Wrench
1/2" Socket and Wrench
9/16" Socket and Wrench
5/16" Allen Wrench
Drill with Phillips Driver Bit
3/8" Drill Bit
1/8" Drill Bit
Hammer
Tape Measure
Utility Knife
2 ft level
Carpenters Square
6' to 8' Step Ladder
RECOMMENDED TOOLS:
Impact Driver
(2) Saw Horses
(4) Bar Clamps or C-Clamps

Here are some maintenance tips required to insure safe enjoyment of your equipment for years to come.
A. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed,
swing seats, chains, ladders, slides, rope and wood components for signs of deterioration and replace if necessary.
B. On a yearly basis, we recommend that you coat your playset with a sealant or preservative. You may also want to spot
sand any areas prior to sealing. Be sure that the sealant you select is non-toxic and child safe.
C. Do not use line trimmers or “weed eaters” around your play equipment. The line will remove both stain and wood
from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited
warranty.
D. Remove plastic swing seats and take indoors or do not use when the temperature drops below 0º F.
Welcome to our family of ready-to-build backyard play equipment. Woodplay playsets are designed with ease of
assembly in mind and we provide these step-by-step installation instructions.
fAfter reading the information below, locate your structure site and carefully unpack parts. As you unpack your playset,
keep the parts identification sheet handy and become familiar with each part before beginning assembly. Remember that
a little extra time spent familiarizing yourself with the parts and instructions before you begin will help you avoid mistakes
and save you time later.
Choosing A Location For Your Playset
Do not install home playground equipment indoors,
or over concrete, asphalt, packed earth, grass, carpet
or any other hard surface. A fall onto a hard surface
can result in serious or fatal injury.
Responsible on-site adult supervision is one of the
most important contributions to children’s safety that
you can make. Woodplay strongly recommends on-
site adult supervision of children of all ages. Safe
swinging and climbing skills need to be taught to
children, just like any other physical activity.
The weight limit for any single user on Woodplay play
equipment is 200 pounds. Limit the number of users
to one on each swing. The tower portion of the play
system will accommodate four (4) additional users.
When the time comes to disassemble and dispose of
the play equipment, do so in such a way that no
hazards will exist at the time the equipment is
discarded.
If you have any questions about your playset, or are in need of replacement parts, call 1-800-GO-SWING.
Please keep these instructions for future reference.
Maintaining Your Playset
I N T R O D U C T I O N
2
When selecting your structure site, always keep the
child’s safety in mind. Here are some recommendations
to help you create a safe play area.
A. The playset should be located on level ground. The
stationary components such as ladders and slides are
REQUIRED to be a minimum of six feet from any structure
or obstruction such as a fence, garage, house, tree or
overhanging branches, electrical wires or clotheslines.
Any swinging equipment is also to be a REQUIRED
minimum distance twice the height of the swing beam
away from these obstructions or structures as well. We
also recommend that you do not install your playset
near a lake, river, swimming pool or other water hazard.
B. The U.S. Consumer Product Safety Commission (CPSC)
recommends that you install and maintain a resilient
surface under your play equipment. The CPSC’s
Consumer Information Sheet for Playground Surfacing
Materials at the end of this manual. A resilient surface,
should be installed after the equipment has been
completely assembled according to these instructions.
The equipment must rest on solid ground. Please note
that this product has a maximum fall height of 8’.

In Addition, Adults Must:
• Not to walk close to, in front of, behind, or between
moving items.
• Not to twist the swing ropes, or loop them over the
top support bar, since this may reduce the strength
of the rope.
• Not to swing empty swing seats.
• Not to swing sideways into the path of adjacent
swings.
• Not to use the equipment in a manner other than
that for which it is intended.
• Not to get off the equipment while it is
in motion.
• Not to jump off the tower.
• Not to climb or swing when they are wet or when the
equipment is wet.
• Not to stand in the swing seats.
• Not to ride or leave bicycles or other toys in the
swing area.
• Not to use hammers, saws, nails, or wrenches on
the equipment.
• Not to swing so high that chains become slack, or
above the height of the swing support.
• Not to jump on a slide.
• Not to climb on top of the swing support.
• Not to attach to the playground equipment any item
that is not specifically designed for use with the
equipment, such as (but not limited to) jump ropes,
clotheslines, pet leashes, cables, and chains. These
may become strangulation hazards.
• To sit in the center of the swings with their full.
weight on the seats.
• To hold on to swings and climbers with.
both hands.
• To slide feet first, never head first..
• To watch for other children while swinging or playing.
near the equipment.
• Limit climbing and swinging heights to each child’s
ability.
• Verify that suspended climbing ropes are secured at
both ends.
• Verify that suspended climbing ropes cannot be
looped back on themselves.
• Dress children appropriately for play. Use well-fitting
shoes that do not have slippery soles.
Avoid ponchos, scarves, hoods, loose-fitting clothing,
neckties, and any clothing with a drawstring. Serious
injury could result should any part of the children’s
clothing become entangled in the equipment.
• Do not allow children to play wearing helmets.
• Remember that children are inventive. When they
develop games that are unsafe, be alert and change
the rules.
Teach Children:
3
S A F E T Y I N S T R U C T I O N S

PART # DESCRIPTION QTY.
ITEM #
15
16
20
17
21
9
19
18
7
3
2
5
6
4
8
1
26
27
PG-14-0018
PG-14-0019
PG-14-0020
PG-16-0001
PG-24-0019
PG-24-0020
PG-24-0026
PG-24-0030
PG-26-0018
PG-26-0014
PG-26-0015
PG-26-0017
PG-44-0013
PG-44-0016
PG-44-0018
PG-44-0024
PG-44-0028
PG-24-0031
Short deck board
Thin deck board
rail upright
Wide deck board
rail upright w/handle holes
hole facia board
corner facia
deck joist
main beam
hole facia
hole facia w/rope hole
6 hole facia
top joist w/swing holes
corner upright w/T J hole
angled brace
corner upright
vertical roof support
ladder side
2
4
17
6
6
6
4
2
4
6
1
2
1
2
8
2
2
2
PG122W TIGER TOWER BASE
PG122W TIGER TOWER BASE HARDWARE
53
39
62
44
52
38
47
69
45
57
55
40
46
50
51
48
PG-HW-L002
PG-HW-L004
PG-HW-L003
PG-HW-W001
PG-HW-W002
PG-HW-W003
PG-HW-W004
PG-HW-W007
PG-HW-S001
PG-HW-S002
PG-HW-S003
PG-HW-S004
PG-HW-S005
PG-HW-N001
PG-HW-N003
PG-HW-B001
1/4" x 4.5" Hex lag screw
5/16" x 3" Hex lag screw
5/16" x 2.5" Hex lag screw
#10 Flat washer
1/4" Flat washer
5/16" Flat washer
3/8" Flat washer
FW1(3/8" 1.46 X19.03 X 8.7)
#10 x 1 round head screw
#8 x 1.25 round head screw
#8 x 1.5 screw
#8 x 2 PH Flat HD WDSCR
#8 x 3 PH Flat HD WDSCR
3/8 Nylon locknut
3/8-16 Acron nut
3/8-16 x 6.5 Hex bolt
4
90
1
38
4
90
4
1
38
16
68
84
8
2
2
2
PART # DESCRIPTION QTY.
ITEM #
PG-AC-0004
PG-AC-0005
PG-AC-0007
PG-HW-M007
PG-AC-0011
PG-AC-0002
PG-AC-0001
PG122W TIGER TOWER BASE ACCESSORIES
Telescope
Ships wheel(Small)
Vinyl Roof (2288mm x 1150mm)
T- metal bracket for Tree house
Name plate
Small Handle(Yellow)
Ladder Tread
PART # DESCRIPTION
4
S T A N D A R D P A R T S L I S T
60
61
58
56
70
29
28
ITEM # QTY.
1
1
1
2
1
2
4

5
TIGER TOWER WALL
34-1/2" 4 Hole RWB
34-1/2" 2 Hole inside RWB
34-1/2" RWB w/rope hole
13-3/4" Corner facia
Rock wall support
4
6
1
2
2
24
25
23
19
22
PG-16-0003
PG-16-0004
PG-16-0005
PG-24-0026
PG-24-0032
PART # DESCRIPTION QTY.
ITEM #
TIGER TOWER WALL
HARDWARE
3/8"-16 x 1/2" T-nut
3/8-16 x1 socket head screw
#10 Flat washer
#10 x 1 round head screw
#8 x 2 PH Flat HD WDSCR
1/4" Flat washer
5/16" x 3" Hex lag screw
1/4" x 4.5" Hex lag screw
5/16" Flat washer
41
43
44
45
40
52
39
53
38
PG-HW-N002
PG-HW-B008
PG-HW-W001
PG-HW-S001
PG-HW-S004
PG-HW-W002
PG-HW-L004
PG-HW-L002
PG-HW-W003
PART # DESCRIPTION
14
14
18
18
44
2
2
2
2
QTY.
ITEM #
S T A N D A R D P A R T S L I S T
29
59
42
ITEM #
TIGER TOWER
WALL ACESSORIES
Small Handle(Yellow)
Rope
Climbing Rock(7Y/7G)
2
1
14
PG-AC-0002
PG-AC-0006
PG-AC-0003
PART # DESCRIPTION QTY.

PICNIC TABLE HARDWARE
5/16" Flat washer
5/16" x 3" Hex lag screw
#8 x 2 PH Flat HD WDSCR
#8 x 1.5 screw
38
39
40
55
PG-HW-W003
PG-HW-L004
PG-HW-S004
PG-HW-S003
6
6
34
4
PART # DESCRIPTION QTY.
ITEM #
TIGER TOWER PICNIC TABLE
4
3
2
1
2
2
13
9
10
14
12
11
PG-16-0002
PG-24-0020
PG-24-0027
PG-24-0028
PG-24-0029
PG-26-0016
PART # DESCRIPTION QTY.
ITEM #
47-1/2" Table board
52" 2 hole facia
45-1/4" Seat board
20" table runner
8" seat runner
50" seat board
S T A N D A R D P A R T S L I S T
SWING BEAM
136" 3 Position Head Beam
104" 2 Position Head Beam
112" A Frame Leg
65"a-frame Cross Brace
U-joint Center Space Block
U-joint Outside
3/8" Flat Washer
3/8" Nylon Locknut
3/8" Standard Nut
3/8" Lock Washer
3/8"-16x6.5" Hex Bolt
3/8-16 X 6.5 Carriage Bolt
1/2"-13 Acorn Nut
1/2"-13x11.5" Hex Bolt
1/2" Flat Washer
1/2"-13x10" Hex Bolt
1/2"-13 Nylon Locknut
5/16" Flat Washer
5/16"x5" Lag Screw
3/8"-16 Acorn Nut
5/16"x2.5" Lag Screw
3/8"-16x9" Hex Bolt
Belt Swing Green W/chain
Belt Swing Yellow W/chain
Angle Bracket
Triangle Swing Beam Plate
Ductile Swing Hanger
Trapeze Set
Spring Clip
30
30
33
32
35
34
47
50
76
74
48
75
68
67
65
66
49
38
63
51
62
64
73
73
31
37
36
72
71
PG-46-0004
PG-46-0005
PG-44-0006
PG-44-0005
PG-44-0008
PG-44-0007
PG-HW-W004
PG-HW-N001
PG-HW-N008
PG-HW-W007
PG-HW-B001
PG-HW-B011
PG-HW-N005
PG-HW-B005
PG-HW-W005
PG-HW-B004
PG-HW-N004
PG-HW-W003
PG-HW-L006
PG-HW-N003
PG-HW-L003
PG-HW-B003
PG-AC-0008
PG-AC-0009
PG-HW-M003
PG-HW-M004
PG-HW-M002
PG-AC-0010
PG-HW-M008
PART # DESCRIPTION
1
2
1
1
2
24
11
2
2
10
2
2
1
6
1
2
7
4
2
3
1
1
1
2
1
4
4
ITEM #
1
2
1
1
2
32
15
2
2
14
2
2
1
6
1
2
7
4
2
3
1
1
1
2
1
6
1
6
6
QTY.
PG204
QTY.
PG205

H A R D W A R E I D E N T I F I C A T I O N
7
Measurement taken from bottom of bolt head to the bottom of bolt
#53 - 1/4 x 4.5 Lag Screw QTY (6)
3/8” Nylon Locknut
QTY (17)
QTY (4)
#43 - 3/8-16 X 1” Socket Head Screw
QTY (14)
#48 - 3/8" -16 X 6 1/2"Machine Bolt
QTY (16)
1/4" Flat Washer 5/16” Flat Washer
3/8" Flat Washer
QTY (36) QTY (105)
QTY (6)
3/8” -16 Acorn Nut
QTY (4)
#10 Flat Washer
QTY (56)
3/8”-16 x 1/2” T-Nut
QTY (14)
#39 - 5/16 x 3” Lag Screw QTY (98)
#62 - 5/16 x 2.5” Lag Screw
1/2 Nylon Locknut
QTY (2)
1/2 Flatwasher
QTY (6)
#63 - 5/16 x 5" Lag Screw QTY (4)
1/2-13 Acorn Nut
QTY (2)
#68
#65 #49 #41 #50
#47 #52 #38 #44 #51
0
1
2
3
4
5
6
7
8
9
QTY (56)
#10 x 1” Round Head Screw
#45
QTY (16)
#8 x 1.25” Round Head Screw
#57
QTY (56)
#8 x 1.5” Flat Head Wood Screw
#55
#75 - 3/8 X 6.5” Carriage Bolt (2)

#76 (3/8” Standard Nut )
2 Pcs.
H A R D W A R E I D E N T I F I C A T I O N
0
1
2
3
4
5
6
7
8
9
8
Ductile Swing Hanger
QTY (6)
#36
Angle Bracket
QTY (2)
#31
Triangle Swing Beam Plate
QTY (1)
#37
#67 1/2"-13 X 11.5" HEX BOLT QTY (1)
#66 1/2"-13 X 10" HEX BOLT QTY (1)
#64 3/8"-16 X 9" HEX BOLT QTY (1)
#8 x 3” Phillips Flat
QTY: (8)
#46
QTY: (162)
#8 x 2” Phillips Flat
#40
T-Bracket
QTY: (2)
#56
#71
SPRING CLIP
PG-HW-M008
QTY (6)
PG-AC-0011
NAME PLATE
#70
(1)
3/8” STANDARD
WASHER
#69
QTY (1)
Head Wood Screw
Head Wood Screw
#74 (3/8” Lock Washer)
2 pcs

#15
45 1/4”
SHORT DECK BOARD
PG-14-0018
QTY. (2)
#20
27 1/2”
RAIL UPRIGHT SLAT
PG-14-0020
QTY. (13)
#16
52”
DECK BOARD
PG-14-0019
QTY. (4)
#17
52”
DECK BOARD
PG-16-0001
QTY. (6)
#13
47 1/2”
TABLE BOARD
PG-16-0002
QTY. (4)
#24
34 1/2”
2 HOLE ROCK WALL BOARD
PG-16-0003
QTY. (4)
#25
34 1/2”
1 HOLE ROCK WALL BOARD
PG-16-0004
QTY. (6)
#23
34 1/2”
ROCK WALL BOARD WITH ROPE HOLE
PG-16-0005
QTY. (1)
9
#09
52”
2 HOLE FASCIA BOARD
PG-24-0020
QTY (8)
#21
27 1/2”
RAIL UPRIGHT
PG-24-0019
QTY (6)
#10
45 1/4”
SHORT SEAT BOARD
PG-24-0027
QTY. (2)
#18
52”
DECK JOIST
PG-24-0030
QTY. (2)
P A R T S I D E N T I F I C A T I O N
#08
ANGLE BRACE
PG-44-0018
QTY. (8)

#22
59 3/8”
ROCK WALL SUPPORT
PG-24-0032
QTY. (2)
#27
55 3/8”
LADDER SIDE
PG-24-0031
QTY. (2)
10
#03
52”
4 HOLE FASCIA BOARDS
PG-26-0014
QTY. (6)
#26
44”
VERTICAL ROOF SUPPORT
PG-44-0028
QTY. (2)
#02
52”
4 HOLE FASCIA BOARD WITH ROPE HOLE
PG-26-0015
QTY. (1)
#07
52”
MAIN BEAM
PG-26-0018
QTY. (4)
#05
52”
6 HOLE FASCIA BOARDS
PG-26-0017
QTY. (2)
#11
50”
LONG SEAT BOARD
PG-26-0016
QTY. (2)
#06
52”
TOP JOIST WITH SWING HOLES
PG-44-0013
QTY. (1)
#01
93”
CORNER UPRIGHT
PG-44-0024
QTY. (2)
#04
52”
CORNER UPRIGHT WITH TOP JOIST HOLE
PG-44-0016
QTY. (2)
P A R T S I D E N T I F I C A T I O N

P A R T S I D E N T I F I C A T I O N
3 POSITION HEADBEAM
PG-46-0004
QTY (1)
A-FRAME LEG
PG-44-0006
QTY (2)
A-FRAME CROSSBRACE
PG-44-0005
QTY (1)
U-JOINT CENTER SPACE BLOCK
PG-44-0008
QTY (1)
11
#30 #32
#33
#35
U-Joint Outside
PG-44-0007
QTY (2)
#34
#28
LADDER TREAD
PG-AC-0001
QTY. (4)
#29
SMALL HANDLE
PG-AC-0002
QTY. (4)
#42
CLIMBING ROCK
PG-AC-0003
QTY. (14)
#60
TELESCOPE
PG-AC-0004
QTY. (1)
#61
SHIPS WHEEL
PG-AC-0005
QTY. (1)
#58
CANOPY
PG-AC-0007
QTY. (1)
#59
ROPE
PG-AC-0006
QTY. (1)
#12
8”
SEAT RUNNER
PG-24-0029
QTY (2)
#19
13 3/4”
CORNER FASCIA BOARD
PG-24-0026
QTY (6)
#14
20”
TABLE RUNNER
PG-24-0028
QTY (1)
136” 65”
112”112”
#73
Belt swing green w/chain
PG-AC-0008 (1)
Belt swing Yellow w/chain
PG-AC-0009 (1)
#72
TRAPEZE SET
PG-AC-0010
(1)
OR
#30
104” 2 POSITION
HEADBEAM
PG-46-0005
QTY (1)

12
C O R N E R - U P R I G H T - A S S E M B L Y “ A ”
1. Lay Corner Uprights #01 on the ground and attach 4 Hole Fascia Board #03 flush w/bottom and sides of corner
uprights using Lag Bolt #39, and Flat Washer #38.
2. From bottom of 4 Hole Fascia Board #03 measure up 82 5/8” and attach 4 Hole Fascia Board W/Rope #02 Hole using
Lag Bolt #39 and Flat Washer #38.
NOTE: Make sure parts are flush and square.
#38
#39
#03
#02
#01
82 5/8”
PARTS NEEDED
#01 93” CORNER UPRIGHT (2)
#02 52” 4 HOLE FASCIA BOARD WITH ROPE HOLE (1)
#03 52” 4 HOLE FASCIA BOARD (1)
HARDWARE NEEDED
#38 5/16” FLAT WASHER (8)
#39 5/16” X 3” LAG SCREW (8)
FLUSH

13
C O R N E R - U P R I G H T - A S S E M B L Y “ B ”
1. Lay Corner Uprights #04 on the ground and attach 4 Hole Fascia Board #03 flush w/bottom and sides of Corner Uprights #04 using
Lag Bolt #39 and Flat Washer #38.
2. From bottom of 4 Hole Fascia Board #03 measure up 80 3/4" and attach Top Joist W/Swing Holes Board #06 using Bolt #48,
Flat Washer #47, Hex Nut #50, and Acorn Nut #51.
Note: Make sure parts are flush and square.
#47
#50
#51
#39
#38
#48
#03
#04
#06
PARTS NEEDED
#03 52” 4 HOLE FASCIA BOARD (1)
#04 93” CORNER UPRIGHT WITH TOP JOIST HOLE (2)
#06 52” TOP JOIST WITH SWING HOLES BOARD (1)
HARDWARE NEEDED
#38 5/16” FLAT WASHER (4)
#39 5/16” X 3” LAG SCREW (4)
#47 3/8” FLAT WASHER
(4)
#48 3/8”-16 X 6.5” HEX BOLT (2)
#50 3/8” NYLON LOCKNUT (2)
#51 3/8” ACORN NUT (2)
COUNTER SINK
DOWN

U P R I G H T - A S S E M B L Y
1. Stand up each Assembly from steps 1, and 2 and attach 4 Hole Fascia Board #03 and 6 Hole Fascia Boards #05 to Corner Uprights
using Lag Bolt #39, and Flat Washer #38.
2.Bottoms of 6 Hole Fascia Boards #05 should be flush with the bottoms of 4 Hole Fascia Board w/Rope Hole #02. As shown.
3. 4 Hole Fascia Boards #03 must be flush w/Bottoms of and Sides of Corner Uprights and they must be oriented as shown.
4. Check that assembly is square w/carpenters square .
5. Tighten all hardware.
80 5/8 "
#38
#39
#03
#05
FLUSH
FLUSH
NOT
FLUSH
PARTS NEEDED
#03 52” 4 HOLE FASCIA BOARD (2)
#05 52” 6 HOLE FASCIA BOARD (2)
HARDWARE NEEDED
#38 5/16” FLAT WASHER (16)
#39 5/16” X 3” LAG SCREW (16)
14
#05
#03

15
M A I N - B E A M - I N S T A L L A T I O N
1. Orient Main Beams #07 and attach to Corner Uprights using Lag Bolts #39, and Flat
OFFSET COUNTERSUNK HOLES IN MAIN BEAM
TOWARD BOTTOM (AS SHOWN)
46 1/8"
#07
#38
#39
PARTS NEEDED
CORNER UPRIGHT ASSEMBLY (1)
#07 52” MAIN BEAM (2)
HARDWARE NEEDED
#38 5/16” FLAT WASHER (8)
#39 5/16” X 3” LAG SCREW (8)
Washer #38.

HARDWARE NEEDED
#38 5/16” FLAT WASHER (4)
#39 5/16” X 3” LAG SCREW (4)
#40 #8 X 2” FLAT HEAD WOOD SCREW (18)
16
P I C N I C - T A B L E - A S S E M B L Y
1. Attach 2 Hole Fascia Boards #09 to inside of Corner Uprights #01, and # 04 using Lag Screw #39, and Flat Washer #38.
2. Center and attach Seat Boards #10, and #11 to 2 Hole Fascia Boards #09 using Phillips Flat Head Woodscrew #40.
3. Center and attach Seat Runners #12 to the under side of Seat Boards #10, and #11 using Phillips Flat Head Woodscrew
#40.
3 1/4”
#40
#10
#12
#09
#39
#38
#04
PARTS NEEDED
#09 52” 2 HOLE FASCIA BOARD (2)
#10 45 1/4"” SHORT SEAT BOARD (2)
#11 50” LONG SEAT BOARD (2)
#12 8” SEAT RUNNER (2)
#11
#11
#10
IF YOU ARE INSTALLING THE OPTIONAL PICNIC TABLE CONTINUE WITH THIS STEP. IF THE PICNIC
TABLE WILL NOT BE INSTALLED GO TO PAGE 18 TO CONTINUE WITH PLAYSET ASSEMBLY.

17
P I C N I C - T A B L E - A S S E M B L Y “ B ”
15 3/8"
15 3/8"
#38
#39
#40
#13
#09
#14
9 1/4”
#55
PARTS NEEDED
#09 52” 2 HOLE FASCIA BOARD (2)
#13 47 1/2” TABLE BOARD (4)
#14 20” TABLE RUNNER (1)
HARDWARE NEEDED
#38 5/16” FLAT WASHER (4)
#39 5/16” X 3” LAG SCREW (4)
#40 #8 X 2” FLAT HEAD WOOD SCREW (16)
#55 #8 X 1.5” FLAT HEAD WOOD SCREW (4)
1. Attach 2 Hole Fascia
Boards #09 to inside
of Corner Uprights #01
and #04, 9 1/4" from top
of 2 Hole Fascia Boards #09
using Lag Screw #39 and
Flat Washer #38.
2. Attach 2 Table Boards #13
to 2 Hole Fascia Boards #09,
15 3/8” from of each side as
shown using Phillips Flat Head
Woodscrew #40.
3. Evenly space the
remaining Table Boards #13
between the 2 attached Table
Boards #13 and attach using Phillips
Flat Head Woodscrew #40.
4. Center and attach Table Runner #14
to the underside of Table Boards #13
using Phillips Flat Head
Woodscrew #55.
#40

18
D E C K - A S S E M B L Y
# 18
# 40
# 17
# 16
# 15
1. Center and evenly space Deck Boards #16, and #17 between Corner Uprights #01, and #04
and attach Deck Boards #16, and #17 to Main Beams #07 using Phillips Flat Head Woodscrews #40.
NOTE: Deck Boards must be evenly spaced.
2. Center and attach Deck Joist #18 to the underside of Deck Boards #16, and #17 using Phillips
Flat Head Woodscrew #40.
PARTS NEEDED
#15 45 1/4” SHORT DECK BOARD (2)
#16 52” THIN DECK BOARD (4)
#17 52” WIDE DECK BOARD (6)
#18 52” DECK JOIST (2)
HARDWARE NEEDED
#40 #8 X 2” FLAT HEAD WOOD SCREW (60)

19
DECK BOARDS NOT SHOWN FOR CLARITY
Attach Angled Braces #08 to Corner Uprights #01, and 04 using Lag Screw #39, and Flat Washer #38. 1.
NOTE: Tops of Angled Braces should be touching the bottom of the Deck Boards
2. Attach Angled Braces #08 to Main Beams #07 using Lag Screw #39, and Flat Washer #38 .
#38
#39
#08
A N G L E D - B R A C E - I N S T A L L A T I O N
PARTS NEEDED
#08 ANGLED BRACE (8)
HARDWARE NEEDED
#38 5/16” FLAT WASHER (12)
#39 5/16” X 3” LAG SCREW (12)
#01
#07

F A S C I A - B O A R D - I N S T A L L A T I O N
20
#09
#03
#07
#38
#39
FLUSH
1. Attach 4 Hole Fascia Board #03 and Main Beam #07 to Corner Uprights #01, and #04 using Flat Washer #38
Hex Lag Screw #39. Tops of the Fascia Boards #02, and #09 and Main Beam Boards should be flush with the
3. Attach Main Beams #07 to Angled Braces #08 using Flat Washer #38, Lag Screw #39, and Flat Head Woodscrew #46.
4. Attach Corner Fascia Board #19 to Corner Uprights #01, and #04 using Flat Washer #38, and Hex Lag Screw #39.
Corner Fascia Boards #19 should rest on top of 4 Hole Fascia Boards #02, and #03,and Main Beams #07
attached with Flat Washer #52, and Hex Lag Screw #53.
5. Attach 2 Hole Fascia Board #09 to Corner Uprights #01, and #04 using Flat Washer #38, and Lag Screw #39.
tops of Deck Boards #16, and #17.
*Note: Main Beams must be oriented with the offset counter-sunk toward bottom.
PARTS NEEDED
#03 52” 4 HOLE FASCIA BOARD (2)
#07 52” MAIN BEAM (2)
#09 52” 2 HOLE FASCIA BOARD (1)
#19 13 3/4” CORNER FASCIA BOARD (4)
HARDWARE NEEDED
#38 5/16” FLAT WASHER (27)
#39 5/16” X 3” LAG SCREW (27)
#46 #8 X 3” FLAT HEAD WOODSCREW (8)
#52 1/4” FLAT WASHER
(4)
#53 1/4” X 4.5” LAG SCREW (4)
TOPS FLUSH
COUNTER SUNK HOLES
TOWARD BOTTOM
#46
#19
#38
#39
#53
#52
#38
#39
2. Secure Deck Joist #18 to Main Beam #07 using wood screw #46