ESCALADE Prince EVOLUTION User manual

MODEL NO.
T8860
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
A S S E M B L Y I N S T R U C T I O N S
Contact Escalade® Sports customer service department at:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [email protected]
Please Do Not Return This
Product to the Store!
2L-4240-01
2015 Escalade Sports
Ó
“ E V O L U T I O N ”
T A B L E T E N N I S T A B L E

Prince (tm) is a trademark of Prince Sports, LLC.
© 2015 Prince Sports, LLC.
www.princetennis.com
P R E - A S S E M B L Y T I P S
Contact Escalade® Sports customer service department at:
Phone: Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please Do Not Return This Product To The Store!
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
1-866-873-3528
2L-4240-01
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for
kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Tools required for assembly: Phillips Screwdriver, one 9/16” Wrenches, Two 7/16” Wrenches (Ratchet and 9/16”, 7/16” Sockets are
recommended and can be substituted for wrenches), Rubber Mallet or Hammer.
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could over-tighten the
and strip the screws out of the wooden table top.
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
P R E - A S S E M B L Y T I P S
2015 Escalade Sports
Ó

23
#10-24 X 1/2 Phillips
Pan Head Screw
1/4"
Plastic
Washer Washer
Plastic
3/8"
28 30
31
32 5
34
35 37
1/4-20 X 3 1/4 Carriage Bolt #8 X 9/16
SMS
#8-32 X 1 1/4
Sheet Metal Screw 3/8" Long Spacer
3/4" Long Spacer
39
36
1/4-20 X 2 3/4 Hex Head Bolt
29
HARDWARE IDENTIFIER
3/8-16
Nyloc
Locknut 1/4-20 X 1 1/2 Phillips
Truss Head Screw
1/4-20 Nyloc
Locknut
27
3/8-16 x 3 1/2 Hex Head Bolt
3/8-16X2 3/4 Hex Head Bolt
13
(Qty. 4) (Qty. 12)
(Qty. 8)
(Qty. 12)
(Qty. 4) (Qty. 4) (Qty. 176)
(Qty. 4) (Qty. 4) (Qty. 4) (Qty. 12) (Qty. 8)
(Qty. 8)
3/8 Push Nut
11
(Qty. 4)
38
(Qty. 4)
1/4-20 Wing Nut
(Qty. 4)
44
#10-24 Locknut
(Qty. 4)
Sorting your hardware ahead of time will speed up assembly time. Sort all your hardware now so it will be
ready before you start assembly.
NOTE:
3

1A. Attach Caster Wheels (#9 & #10) to Caster Beam. Slide a Caster Wheel with Lock (#10) through Caster Beam (#8) and
secure it with a Push Nut (#11) as shown in Figure 1. Gently tap the Push Nut (#11) with a hammer or rubber mallet to
secure it in place. On the other end of the Caster Beam attach a Caster Wheel without Lock (#9). Make sure you have one
Caster Wheel with Lock and a Caster Wheel without Lock for each Caster Beam. Repeat step for second Caster Beam.
1B. Attach Tube Plugs (#14) to Caster Beams (#8) as shown in Figure 1.
Caster
with
Lock
Caster
without
Lock
11
HARDWARE NEEDED
3/8 Push Nut
(Qty. 4)
NOTE: Make sure logo is
right side up and
facing as shown.
1
Figure
ASSEMBLY TIP
On the top of each page you will find a picture of the
Hardware Needed (to scale) along with the Quantity,
Key# and Description. You can lay the hardware on
the picture to identify and sort the hardware.
Having a second person sort hardware and
hold parts will speed up assembly time
and make it easier to assemble your table.
NOTE:
9
10
11
14
8
4

8
10
10
43
2. Lay Support Plates (#43) on Caster Beam (#8) to line up holes, the distance between middle
holes to side holes is different, see Front View of Figure 2. Attach Stop Spools (#12) and
Support Plates (#43) to side of Caster Beam without logo with Bolts (#13) and Nuts (#28)
but DO NOT tighten completely yet this will be done in a later step. See Figure 2.
Repeat step for second Caster Beam.
13
28
43
12
8
Longer
Shorter
Longer
Shorter
Match holes in Support Plate (#43)
with Caster Beam (#8).
2813 3/8-16 X 2 3/4 Hex Head Bolt
(Qty. 8) 3/8-16 Locknut
(Qty. 8)
Front View
HARDWARE NEEDED
Logo on
this side
2
Figure
5

Note: Support Plate (#43)
must be on inside of Caster
Rail (#8) as shown.
8
43
8
32
32
31
31
3. Attach Wood Bottom Board (#15) to Caster Beam
Assemblies (#8) as shown in Figure 3. Turn Caster Beams
as shown and attach board with four Carriage Bolts (#31)
and four Wing Nuts (#32). Tighten Wing Nuts securely.
32
31
(Qty. 4)
1/4-20 Wing Nut
HARDWARE NEEDED
1/4-20 X 3 1/4 Carriage Bolt
(Qty. 4)
NOTE: Make sure logos are right side up and
facing the outside as shown.
Caster
with
Lock
Caster
with
Lock
15
3
Figure
READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)
ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!
6
CAUTION

4. Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#8) as shown in Figure 4.
a) Loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43) and Caster Beam
(#8) as shown in the Top View and Figure 4.
b) Slide one Hex Bolt (#27) through Caster Beam (#8), one Plastic Washer (#39), Strut Tube (#17), Plastic Washer
(#39), Support Plate (#43) Spacer (#36), Linkage (#16) and Locknut (#28) as shown in Figure 4 and Top View.
c) Repeat on other end of Caster Beam (#8) and on second Caster Beam.
d) Tighten Bolts (#13) and Nuts (#28) (installed in Step 2) securely.
e) Tighten Nuts (#28) on Bolts (#27) securely but DO NOT over tighten, Strut Tube
must Pivot Freely.
3/8-16
Locknut
(Qty. 4)
28
HARDWARE NEEDED
27 3/8-16 x 3 1/2 Hex Head Bolt
(Qty. 4)
36 39
3/4" Long Spacer
(Qty. 4)
3/8" Plastic
Washer (Qty. 8)
Top View
27
39
36
28
17
43
12
16
13 13
8
Note: Linkages and Strut
tubes must be turned as
shown or table will not
operate correctly.
8
16
17
16
27
36
28
39
17
28
4
Figure
7

5. Lay Table Top (#1) painted side down, on a smooth, flat surface. Use the shipping
container to protect the painted surface of table top.
6. Align the ”U” Support (#21) on Table Top (#1) as shown in Figure 5.
7. Align all four holes in each U-Clip (#22) with the four Indentations in table top. Be sure that Slot
in the Three U-Clips (#22) all face the same direction toward the end of the table with no stripe
and no Indentations. Secure U-Clips (#22) with Screws (#5) as shown in Figure 5 & Detail A.
Note: All four holes in the U-Clip (#22) must align with four Indentations in table top. See Detail A.
Note: All Indentations
guides in table top are
small so look closely.
Note: End with no stripe
and no Indentations.
5
Figure
8. Rotate U-support (#21) that is on bottom of Table Top
until you see the screw holes in the slots of U-clips (#22).
If necessary Slide U-support (#21) side to side and back
and forth to see holes. See Figure 5 & Detail B.
9. Insert Screw (#35) through slot in U-clip (#22) and into U-support
(#21). See Figure 5 & Detail B. Thread screw all the way into U-
support until it touches the back of the tube. There should be about
3/8” of screw (#35) left sticking out. Repeat for second Screw (#35)
and U Clip (#22).
Note: To aid in assembly you can use a cordless drill and
Phillips bit. Wear safety glasses.
Or
Scan with your smartphone:
Detail A
21
22
35
1
5
21 22
Slot in
U-Clip
1
Detail B
35 #8-32 X 1 1/4
Sheet Metal Screw
(Qty. 2)
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 12)
If you want to see a video on how to insert Screw (#35) go to:
http://www.escaladesports.com/customer-service/instruction-videos
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS (#22) BE TURNED
AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY, YOU WILL DO IRREPARABLE DAMAGE
TO YOUR TABLE WHEN YOU ATTEMPT TO OPEN IT TO THE PLAYING POSITION.
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
8
NOTICE NOTICE

10. Assemble parts to the bottom of the table top with Screws (#5) as shown in Figure 6,
Detail C and Detail D.
a) Align the holes in the Mounting Brackets (#25) & (#20) with Indentations in table
top assembly and secure with screws (#5) as shown. All holes in each Mounting
Bracket must align with Indentations in the top. See Figure 6 and Detail C.
b) Align the holes in the two U-Support Clips (#6) with Indentations in table top. Be
sure that the two U-Support Clips (#6) are positioned exactly as shown in Figure 6 &
Detail D.
20
25
5 5
Detail C Note: Indentations
in table top are small
so look closely.
6
5
Detail D
6
6
Figure
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 28)
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE
AND USE CAUTION BECAUSE YOU COULD OVER-TIGHTEN THE
HARDWARE AND STRIP SCREW IN WOOD DOING IRREPARABLE
DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
9
NOTICE

7A
Figure
7B
Figure
Note: You Will Need one hinge in position A and one in position C for the next page. Hinges
are universal and can be rotated into either position A or C. See Figure 7A. Or
Scan with your Smartphone/Tablet:
If you want to see a video on how to rotate hinges go to:
http://www.escaladesports.com/customer-service/instruction-videos
1. Determine in which position your hinges are rotated, if you already have one hinge in Position
A and one in Position C continue to next page.
2. If you have two hinges in Position A rotate one hinge into position C as shown in Figure 7A.
3. If you have two hinges in Position C rotate one hinge into position A as shown in Figure 7B.
FLIP HINGE ASSEMBLY
180 DEGREES
ROTATE BRACKET
180 DEGREES.
NOTE MAKE SURE TO
ONLY ROTATE BRACKET
AND NOT THE ENTIRE
HINGE ASSEMBLY.
ABC
CB A
FLIP BRACKET 180
DEGREES.
NOTE MAKE SURE TO
ONLY FLIP BRACKET
AND NOT THE ENTIRE
HINGE ASSEMBLY.
FLIP HINGE ASSEMBLY
180 DEGREES
Rotating hinge from position A to position C.
Rotating hinge from position C to position A.
NOTE:
10

8
Figure
Note: Hinges must always be positioned as shown, with the “elbow” of the hinge pointing
toward the bottom of the table. In the correct position hinge will look like a “V“,
rotate hinges into position if necessary.
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREWS IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
11. Align the holes in the Hinge Bracket Assembly (#18) with indentations in table
top. Be sure that the straight part of the hinge is facing toward the middle of
the table and placed exactly as shown in Figure 8, Detail E1 & E2.
NOTE:
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 8)
18
Detail E1
The “elbow“
of the hinge should
be pointing towards
the bottom of the table
Hole on the straight
leg of hinge should
be facing up
18
5
Detail E2
Hole on the straight
leg of hinge should
be facing up
The “elbow“
of the hinge should
be pointing towards the
bottom of the table
11
NOTICE

5
47
Detail G1
Flush
Flush
No screw in
this hole
47
Detail G2
No screw in
this hole
19
29
20
34
44
23
38
25
Detail F
Leg Brace
24- Right Hand
Leg Assembly
19- Left Hand
Leg Assembly
26
*NOTE: Hinges not Shown
for clarity.
9
Figure
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 6)
1/4-20 X 2 3/4 Hex Head Bolt
29
(Qty. 2)
1/4"
Plastic
Washer
(Qty. 4)
38
34
1/4-20 Nyloc Locknut
(Qty. 2)
23
#10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 2)
44
#10-24
Locknut
(Qty. 2)
12. Attach legs (#19 & 24) to table top with Hex Bolt (#29), two Plastic Washers (#38)
and Locknut (#34). Attach leg brace to Leg Mounting Bracket (#25) with Phillips
Head Screw (#23) and #10-24 Locknut (#44) as shown in Detail F. Attach leg
levelers (#26) to bottom of the legs (#19 & 24) as shown in Figure 9.
13. Attach Net Plate (#47) as shown in Detail G1 & Detail G2. Make sure
the Nut Plate is flush with the corner of the table and make sure to use
the top three holes in the nut plates. Note: Nut Plates Mount to one
Table Top Only.
Note: There are no Indentations guides for
the nut plates on the table top.
12

5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 24)
3
5
5
Detail H
14. Lay out Rails (#2, #3, & #4) around edges of table
top and add Vinyl End Caps (#45 & 46) to ends of
Left and Right Side rails. See Figure 10.
15. Line up holes in rails with Indentations in table top and
secure using Screws (#5). See Figure 10 & Detail H.
2
44
*NOTE: Legs not
shown for clarity.
46
45
Note: The Prince logo must face out on both the Right hand
Rail (#2) and Left hand Rail (#3).
PRINCE LOGO
ON THIS SIDE
10
Figure
PRINCE LOGO
ON THIS SIDE
13

Detail J
Detail K
5
40
40
18. Repeat steps 5 through 17 for other
table top assembly. Second Table Top
Half does not get Nut Plates (#47),
skip step 12 on the Second Table Half.
17. Lay Corner Caps (#40) on table as shown in Figure 11.
Secure to bottom of table with three Screws (#5). See
Detail K & Detail J.
16. Line up holes in Storage Tray with Indentations in table
top and attach it to the bottom of the table with four
(#5) screws as shown in Figure 11 and Detail L.
NOTE: Prepare an area for the assembly of the second table top
half. If necessary, move the first table top half aside with the aid of a
helper. Be sure to place it in a location where it won't be disturbed
or damaged. If setting on its side, be sure to place the bottom edge
no less than 12 inches away form the wall. Also be sure to place
carpet or pieces of the shipping carton down to protect
table top edges. If floor is not carpeted, brace table
top half with a heavy object to keep it from sliding.
*NOTE: Legs not
shown for clarity.
7
Detail L
11
Figure
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 10)
14

19. Attach Table Top Assembly to Base Assembly (that you put
together in steps 1-4), as shown in Figure 12. Pivot Strut
Tubes (#17) up as shown; then, with at least one adult on
each side of Table Top, lift top and align ends of U-
support tube (#21) with tops of Strut Tubes (#17) on
Caster Beams (#8) as shown in Figure 12. Slide tubes
together.
With at least 2 adults,
slide Table Top Assembly
onto Strut Tubes
TUBES UP
PIVOT STRUT
8
17
8
21
U-Support
Table Top
Assembly
17
Strut Tube
12
Figure
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, U-
SUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN
Y TO ASSEMBLE. TABLE TOPS ARE
LEGS AND TR
HEAVY -
ALONE!
DO NOT ATTEMPT TO ASSEMBLE
HEAVY -
AT LEAST TWO (2) ADULTS ARE NEEDED TO DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
15

20. Secure U-support tube (#21) to Strut Tubes (#17) with two Screws (#5)
as shown in Figure 13. Align holes in U-support with holes in Strut
Tubes and thread screw (#5) into hole in Strut Tube (#17). Tighten
screws all the way but be careful not to over tighten as you could strip
threads on screws.
21. Attach Linkages (#16) to Leg (#19) as shown in Figure 13. Pivot Leg
(#19) out from the table top and pivot both linkages (#16) up and align
hole in Linkage with hole in Leg (#19). Attach Linkage (#16) to Leg
(#19) using Hex Head Bolt (#29), Spacer (#37) and Locknut (#34).
Spacer (#37) goes between Linkage and Leg. Attach other Linkage to
other Leg the same way. Tighten nuts securely.
DO NOT OPEN THE TABLE TO PLAYING
POSITION UNTIL BOTH TOPS ARE
INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD
BE KNOCKED OVER CAUSING SERIOUS
BODILY INJURY OR PROPERTY
DAMAGE.
16
34
37
29
29
37
34
17 5
5
19
24 16
21
Spacer (#37) goes
between Linkage (#16)
and Leg (#19 & #24)
13
Figure
Note: Make sure
to install #5
screws
Note: Make sure
to install #5
screws
34
29
HARDWARE NEEDED
1/4-20 Locknut
(Qty. 2)
37 5
1/4-20 X 2 3/4 Hex Head Bolt
(Qty. 2) 3/8" Long Spacer
(Qty. 2)
#8 X 9/16
Screw
(Qty. 2)
16

CAUTION: Position hinges exactly as
shown in Detail N or table will not
operate correctly and could be damaged.
34
38
30
18
17
18
17
Detail M
ATTENTION: If hinge is positioned as
shown below (Detail M), Rotate the
hinge as shown in Detail N. Do not take
the hinge off the table.
Detail N
Incorrect position
of hinge
Assembly
position of hinge
14
Figure
Or Scan QR code with
your smartphone:
DO NOT OPEN THE TABLE TO PLAYING
POSITION UNTIL BOTH TOPS ARE
INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS
BODILY INJURY OR PROPERTY DAMAGE.
34
HARDWARE NEEDED
30 38
1/4" Plastic
Washer
1/4-20 Locknut
(Qty. 2) (Qty. 2)
1/4-20 X 1 1/2 Phillips
Truss Head Screw
(Qty. 2)
If you want to see a video on how to attach hinges to Strut tube go to:
http://www.escaladesports.com/customer-service/instruction-videos
22. Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 14 & Detail N. With hinge
positioned as shown, align hole in hinge with hole in Strut Tube and attach with ¼” Screw (#30),
Plastic Washer (#38) and Locknut (#34). Plastic Washer (#38) goes between Strut Tube and
Hinge. Tighten nut securely. Repeat for other Hinge. CAUTION: Hinges must be positioned
exactly as shown or table will not operate correctly and could be damaged.
Note: If hinge (#18) is positioned as shown in Detail M, you will have to rotate the hinge
to the position shown in Detail N. DO NOT unscrew the hinge, you can rotate the hinge
without unscrewing it from the table.
23. With at least two adults, repeat steps 19 through 22 for other table top assembly.
17

TO CLOSE:
1. Pivot the net post toward side of the table.
2. Unlock all four hinges.
3. Lift one table half to midpoint until the
plastic clips are engaged. Then continue
lifting until closed.
4. Raise other table half in the same manner.
....as shown in Figure 17.
TO OPEN:
1. Hold center of top edge. Gently pull outward to midway position.
.... Continue to pull until disengaged from plastic clips and legs rest on the
....floor as shown in Figure 15A and 15B. Do not leave table partially
....opened at midway position.
2. Lower second top as described in step 1.
3. Lock all four center hinges. See Figure 16.
4. Attach net posts and net to table as shown in the next page.
PLAYING POSITION
IF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 18)
1. Set the table to the Playing Position and lock hinges as shown in
....Figure 16.
2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create
....enough slack to align table tops. See .Figure 3
3. With the help of two other adults, push the two table top halves so
.... they are in line with each other and re-tighten the Wing Nuts (#32) as
....shown in .Figure 18
OPENING AND CLOSING INSTRUCTIONS
Push to lock hinge.
Plastic
Clip
Midway
Position
PLAYBACK POSITION
Hinge
Locked
To lock hinge push up on
the table and push hinge
as shown in Figure 15B.
STORAGE POSITION
TOP VIEW
Figure 15A Figure 15B
Figure 16
Figure 17
Figure 18
Caution: To prevent damage to the net system
and/or table top, the post assembly must be
pivoted toward side of table before lifting table
tops to storage position. Loosen knob and
pivot net post toward table side as far as it will
go . Re-tighten knob.
EXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, OR CHILDREN NOT
PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE TABLE.
IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.
DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL
DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.
CAUTION
18

3. Storage
Caution: To prevent damage to the net system and/or
table top, the post assembly must be pivoted toward side
of table before lifting table tops to storage position.
Loosen knob and pivot net post toward table side as far
as it will go. Retighten Knob.
Knob
by firmly gripping the vertical net post within height adjustment slot
19

2L-4240-01
Replacement Parts List for Model Number T8860
*PARTS IDENTIFIER ON NEXT PAGE.
Key# DescriptionPart # Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
4A-5536-00
2S-6869-24
2S-6869-25
2S-4670-14
1B-4082-99
3M-6273-00
3M-4166-02
8S-6841-13
2Q-6459-01
2Q-6460-01
2B-4043-00
3M-6884-00
1B-6195-00
3M-6274-00
2W-5045-02
8S-6842-07
8S-6856-07
4A-5423-02
1A-4132-01
2S-4597-01
8S-4160-02
2S-6879-10
1B-4138-00
1A-4133-01
2S-6343-00
2Q-4028-00
1B-6495-00
2B-4053-00
1B-4135-00
1B-4097-01
1B-6459-00
1N-0001-00
NOT USED
2B-4047-98
1B-4089-00
7B-4061-00
7B-6161-00
2B-6087-00
2B-4054-00
3M-4167-00
5A-4243-00
2L-4240-01
2S-6875-01
WB-1007-99
3M-4150-00
3M-4151-00
1A-6285-00
1” BLACK TOP ONLY
2 ½” SIDE RAIL - RIGHT HAND
2 1/2” SIDE RAIL - LEFT HAND
END RAIL
#8 X 9/16 SHEET METAL SCREW
U-SUPPORT CLIP (PLASTIC)
STORAGE TRAY ASSEMBLY
CASTER BEAM ONLY
5" CASTER - NON LOCKING
5” CASTER - WITH LOCK
3/8" PUSH NUT
STOP SPOOL
3/8-16 X 2 3/4 HEX HEAD BOLT
TUBE PLUG - 1" X 2"
BOTTOM BOARD
LINKAGE - GREEN
STRUT TUBE - WHITE
HINGE & MOUNTING BRACKET ASSEMBLY
LEG ASSEMBLY - LEFT HAND
MOUNTING BRACKET ONLY
U SUPPORT
1" U-CLIP
#10-24 X ½ PHILLIPS PAN HEAD SCREW
LEG ASSEMBLY - RIGHT HAND
LEG MOUNTING BRACKET
5/16-18 x 2 1/2” LEG LEVELER
3/8-16 x 3 1/2 HEX HEAD BOLT
3/8-16 NYLOC JAM NUT
1/4-20 x 2 3/4 HEX HEAD BOLT
1/4-20 x 1 1/2 PHILLIPS HEAD SCREW
1/4-20 x 3 1/4 CARRIAGE BOLT
1/4-20 WING NUT
NOT USED
1/4-20 NYLOC JAM NUT
#8-32 x 1 1/4 SHEET METAL SCREW
3/4 OD X 13/32 ID X 3/4 LONG SPACER
1/2 OD X 9/32 ID X 3/8 LONG SPACER
1/4" PLASTIC WASHER
3/8" PLASTIC WASHER
CORNER PROTECTOR
PIVOT NET & POST SET (NOT SHOWN)
OWNERS MANUAL - T8860
SUPPORT PLATE
#10-24 LOCKNUT
RH VINYL END CAP
LH VINYL END CAP
NUT PLATE ASSEMBLY
2
2
2
4
176
8
2
2
2
2
4
8
8
4
1
4
4
4
2
4
2
6
4
2
4
4
4
12
8
4
4
4
12
4
4
4
12
8
4
1
1
4
4
2
2
2
20