ESCALADE Stiga QUICK SERVE 3000 User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 7 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable
wrench may be substituted for the wrenches), Flat Blade Screw Driver
OWNER'S MANUAL
MODEL NO.
T8176T8176
T8176T8176
T8176
QUICK SERVE 3000
TABLE TENNIS TABLE
Please Do Not Return This Product To The Store!
Contact Escalade®Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [email protected]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®SPORTS PRODUCT INFORMATION
2L-6872-01
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2
5. Rotate U-support #7 until you see the screw holes in the slots
of U-clips # 6. Slide U-support #7 side to side if necessary. See
Figure 2.
6. Insert a screw #19 through slot in each U-clip #6 and into U-
support #7. Thread each screw all the way into U-support #7
until it touches the back of the tube. There should be about 3/
8 inch of screw #19 left sticking out.
7. Rotate U-leg #2 until you see the screw holes in the slots of U-
clips #3. Slide U-leg #2 side to side if necessary. See Figure 2.
8. Insert a screw #34 through slot in each U-clip #3 and into U-
leg #2. Thread each screw all the way into U-leg #2 until it
touches the back of the tube. There should be about 3/8 inch
of screw #19 left sticking out.
Figure 2
1. Gently tap four caster sockets #12 into Name Panel Assemblies until flange on sockets touches the edge of the tube. DO NOT HIT
CASTER SOCKET DIRECTLY! Place a block of wood on Caster Sockets and tap on wood with hammer. See Figure 1.
2. Insert casters #11 into caster sockets #12.
3. Connect the two Name Plate Assemblies to the Bottom Board #28, as shown in Figure 1, using four bolts #39 and four nuts #15.
4. Install a safety latch #8 into the right-hand hole on each name panel as shown in Figure 1. Use one screw #10 one washer #17 and one
hex nut #16. NOTE: Flange on safety latch must extend over top of name panel as shown in Figure 1. Safety latch must
pivot freely.
Figure 1
INSTALL SAFETY LATCHES #8 AS SHOWN BELOW FOR PROPER USE OF
TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY
LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!
CAUTION:

3
16. Prepare an area for the assembly of the second table top half. If
necessary, move the first table top half aside with the aid of a helper.
Be sure to place it in a location where it won't be disturbed or dam-
aged. If setting on its side, be sure to place the bottom edge no less
than 12 inches away from the wall. Also be sure to place carpet or
pieces of the shipping carton down to protect table top edges. If
floor is not carpeted, brace table top half with a heavy object to
keep it from sliding.
17. Repeat steps 5 thru 15 on second table half.
9. Lay table top #1 painted side down, on a smooth, flat surface. Use
the shipping container to protect the painted surface of the table
top.
10. Attach end of linkages #4 with two holes to INSIDE of U-leg #2 as
shown in Figure 3. Secure with bolts #14, locknuts #15 and plas-
tic spacers #37. Tighten hardware snug enough to keep table stable
but do not overtighten. Tubes must pivot freely. NOTE: Plastic spac-
ers go between linkages #4 and U-leg #2.
11. Attach other end of linkages #4 to OUTSIDE of U-support #7
with bolts #38, locknuts #15 and plastic washers #24. Tighten
hardware until snug but do not overtighten. Tubes must pivot freely.
12. Install leg cap #13 onto end of U-legs #2.
13. Snap Lower Paddle Box #32 to Upper Paddle Box #33.
AT LEAST TWO (2) ADULTS ARE NEEDED TO
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, U-
SUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN
LEGS AND TRY TO ASSEMBLE. TABLE TOPS ARE
HEAVY - DO NOT ATTEMPT TO ASSEMBLE
ALONE!
DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
Figure 5
18. With two adults, attach table top (#1) to table base, as shown in
Figure 5. With at least one adult on each side of table top, lift top
and align ends of "U"-support tube with top of upright tubes. Slide
tubes together.
19. With two adults, put other table top onto other pivot tubes following
instructions in previous step.
14. On one side of the table attach slotted end of safety strap #35 to
INSIDE of U-Leg #2 using one bolt #38, one spacer #36, one
washer #24, and one locknut #15. Tighten hardware until snug
but do not overtighten. Tubes must pivot freely. See Figure 4.
15. Attach other end of safety strap #35 to OUTSIDE of linkage #4
using one bolt #9, one washer #24, one spacer #36, and one
locknut #15.
Figure 4
Figure 3

4
TO OPEN:
1. Stand behind the table near the safety latch.
2. Hold table half with one hand and pivot safety latch enough to
allow the edge of the table half to pass over it.
3. While keeping an eye on the safety latch, pivot table half until it
moves past the safety latch. Once edge of table has passed over
safety latch, stop pivoting table half.
4. With both hands on the table half, center yourself along the table
half and lower the table half to the floor.
5. Repeat for the other table half.
6. Secure net posts to center of table and slide net down over posts.
NOTE: Net will be tight. It will be necessary to stretch net.
This will insure proper net tension.
TO CLOSE:
1. Remove net and net posts from table.
2. Lift table half upward and inward to vertical position.
3. Check to be sure that table half is locked in the safety latch.
4. Repeat for the other table half.
OPENING AND CLOSING INSTRUCTIONS
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO
NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND, SIT OR JUMP
ON TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE
IS TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
OR PROPERTY DAMAGE.
CAUTION:

5
90 DAY LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE®SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of
ninety (90) days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any
Product of its manufacture is free from defects in material and workmanship when used for the intended
purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAM-
AGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW
INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF
DEFECTS IN MATERIAL AND WORKMANSHIP.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS
shall repair or replace with a comparable model, and Product, or component thereof, which may prove
defective under normal use and proper care, and which our examination shall disclose to our satisfaction
to be thus defective, please contact our Warranty Dept.
1-800-426-1421 / Warranty Dept.
Or Write us at:
Escalade®Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty
Products. ESCALADE®SPORTS strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, ARE LIMITED IN DURATION TO THE ABOVE NINETY (90) DAY WARRANTY PE-
RIOD. ESCALADE®SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER
CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CON-
SUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights
which may vary from state to state.

6
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of
your new table.
THE TABLE TOP
The top (playing surface) of your table is made of particle board. Like all products made of wood, it can be affected by atmospheric changes in both
temperature and humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern
as it does not detract from the play or utility value of the table. After assembly of the table, you can minimize the effects of temperature and humidity
changes by storing the table in the folded up position in a dry area when table is not in use.
STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to
warp, swell, crack or blister. When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may
bow. Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
CLEANING YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS,
ABRASIVE OR CLEANING PRODUCTS on your table's playing surface.
MAINTENANCE OF YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or
similar areas can cause wood to warp, swell, crack or blister.
UNLEVEL FLOORS
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in
different directions to find the best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in
the center, shim up under the outer U-legs.

7
20 701-105 #8 x 9/16 Sheet Metal Screw 120
21 8S-6603-01 Upright Tube 4
22 3M-6483-00 Corner Cap 4
23 3M-6484-00 Side Cap 4
24 2B-6087-00 Plastic Washer 8
25 2S-6375-00 Side Rail 4
26 2S-6391-00 End Rail 4
27 2L-6872-01 Owner’s Manual 1
28 2W-6269-02 Bottom Board 1
30 5A-6700-00 Net and Post Kit 1
31 1B-6469-00 ¼-20 x 1-3/4 Hex Head Bolt 8
32 3M-6500-01 Storage Tray Bottom 2
33 3M-6500-00 Storage Tray Top 2
34 1B-6460-00 #8-32 X 1-3/4 Sheet Metal Screw 6
35 2S-6428M01 Safety Strap 2
36 7B-6257-00 5/16” Spacer 4
37 7B-6256-00 3/4” Spacer 4
38 701-142 ¼-20 x 2 ¼ Hex Head Bolt 6
39 1B-6475-00 ¼-20 x 1 ¼ Hex Head Bolt 4
1 4A-6508-00 3/4" Board 2
2 8S-6638-01 U-leg 2
3 2S-6319-03 1-¼ U-Clip 6
4 8S-6635-01 Linkage 4
5 2S-6419-02 Name Panel 2
6 2S-6381-01 1-1/2" U-clip 6
7 8S-6639-01 U-support 2
8 2S-6264-03 Safety Latch 2
9 701-47 ¼-20 x 1½ Hex Head Bolt 2
10 801-120B #10-24 x 3/4 Phil Rnd Hd Scr 2
11 2Q-6105-01 3" Caster 4
12 2Q-6104-01 Caster Socket 4
13 504-13 Leg Cap 4
14 1B-6477-00 ¼-20 x 3-1/4 Hex Head Bolt 4
15 701-26 ¼-20 Locknut 24
16 601-80B #10-24 Locknut 2
17 701-1B 3/16” Flatwasher 2
19 1B-6452-00 #8-32 x 1½ Sheet Metal Screw 6
PRODUCT PARTS LIST T8176
2L-6872-01
Key # Part # Description Qty. Key # Part # Description Qty.