Eubank V series Installation and operating instructions

Installation, Operation and Maintenance

V SERIES Wallmount Air

Conditioners R410A

Series

REV. 10/26/16

1

678628-W

Your equipment is covered by a LIMITED WARRANTY against

defects in material and workmanship.

This is a vertical, wallmount unit designed for many different

applications in both residential and commercial settings. It is self-

contained and arrives completely assembled, factory-charged and

wired. The unit is 100% run-tested at the factory to ensure proper

operation. Your unit is supplied with high-quality copper tubing and

enhanced aluminum-finned coils for high heat transfer efficiency

and long life. The unit cabinet is constructed of G-90 galvanized

steel. All exterior surfaces are finished with a baked-on polyester

coating. This will provide excellent corrosion protection in most

applications. However, if the unit is installed in an area with a

corrosive atmosphere, such as near an industrial plant or on the

seacoast, additional coating should be considered to extend the

life of the coils and cabinet.

This unit was designed for up to 105ºF of ambient temperature.

INSPECTION AND UNPACKING

A thorough inspection of the shipping container should be made

immediately upon receiving your unit. Look for any punctures or

openings. If it appears as if damage has occurred, it should be

noted on the freight bill before signing. The delivering carrier

should be contacted immediately to inspect damage, and no

installation work should begin until this inspection is completed.

DANGER: BEFORE PERFORMING ANY

WORK ON THIS EQUIPMENT, POWER SUPPLY

MUST BE TURNED OFF AT THE HOUSEHOLD

SERVICE BOX TO AVOID THE POSSIBILITY OF

SHOCK, INJURY, DEATH, OR DAMAGE TO EQUIPMENT.

SAFETY RULES

WARNING: FAILURE TO FOLLOW THESE

RULES AND INSTRUCTIONS COULD CAUSE A

MALFUNCION OR DESTRUCTION OF

EQUIPMENT WHICH COULD RESULT IN

PROPERTY DAMAGE, SERIOUS BODILY INJURY, OR

DEATH.

1. Installation and repair MUST be done by a qualified person.

The equipment should be inspected before use and at least

once annually by a professional service person.

2. AVOID ELECTRICAL SHOCK! Turn power OFF when

servicing. There may be more than one disconnect switch

to de-energize unit.

3.

C

l

o

se

cover(s)

b

e

f

o

r

e

r

e

t

u

r

n

i

ng

breaker(s)

to

“

O

N

”

position.

4. Please observe good safety practices by wearing personal

protective equipment such as gloves and safety glasses to

avoid injury.

5. Installation MUST conform to local codes. In the absence of

local codes, refer to the National Electrical Code (NEC),

ANS/NFPA No. 70-1993 and recommendations made by

the National Board of Fire Underwriters.

In our continuing effort to improve our product, specifications may

change without notice. If there are any questions, please see the

contact information on the last page of this manual.

In all cases, the equipment MUST be installed in accordance with

the installation instructions described in this manual.

WARNING: IMPROPER INSTALLATION MAY

DAMAGE EQUIPMENT, CAN CREATE A HAZARD,

AND WILL VOID THE WARRANTY

OPERATING INSTRUCTIONS

If heating and cooling functions are controlled by separate

thermostats,

turn the

f

u

r

n

a

c

e

thermostat

to the

“

OFF

”

position

during the cooling season to prevent simultaneous operation of the

heating and cooling systems. Reverse the procedure during the

heating season.

If the same thermostat controls both heating and cooling

functions, set the thermostat to either HEAT or COOL as desired.

Set the desired temperature on your thermostat and set the fan

s

w

i

t

ch

to

“

O

N

”

(for

continuous air circulation) or to

“

A

UT

O

MA

T

I

C

”

(for air circulation only when the air conditioning system is

operating).

IMPORTANT: Wait at least three (3) minutes after turning the air

conditioner off before trying to restart. If an attempt is made to start

the compressor before the refrigerant pressures are equalized, the

compressor motor may trip on its overload. An additional waiting

period will be required before restarting.

MAINTENANCE

1. Always install and keep filters clean. Check filters every 2

weeks. Clean or replace if necessary. The factory-installed filter is

located behind the center front access panel.

TO CHANGE SYSTEM FILTER:

A. Turn the power to the unit off at the unit disconnect. The

disconnect is located on the front of the T Series unit

behind a small access door.

B. Remove the front center access door from the unit.

C. Remove and replace the filter with the type and size

indicated in the table below.

D. Replace the access door and turn on the power to the unit.

NOTE: If your system has a filter grille installed in the return air

opening, the unit filter should have been discarded during

installation.

The filter installed into the return air grille assembly should be

replaced with the same size and type provided with the grille.

If your system is equipped with a fresh air intake, the filter for the

fresh air assembly is accessed through the front center panel. The

filter is a permanent washable type.

UN

I

T

M

ODE

L

Q

T

Y

.

F

I

L

T

E

R

S

I

Z

E

TY

P

E

18

,

24

,3

0

,

3

6

1

6

x

2

5

x 1

(st

anda

r

d

)

D

i

s

po

s

ab

le

18

,

24

,3

0

,

3

6

1

6

x

2

5

x 2

(

op

t

i

ona

l)

P

l

ea

t

e

d

48

,

6

0

1

2

0

x

3

0

x 1

(st

anda

r

d

)

D

i

s

po

s

ab

le

48

,

6

0

1

2

0

x

3

0

x 2

(

op

t

i

ona

l)

P

l

ea

t

e

d

WARNING: SERIOUS INJURY MAY RESULT IF

WATER SPRAY IS DIRECTED TOWARD LIVE

ELECTRICAL CONNECTIONS OR POWER

SOURCES.

TO CLEAN FRESH AIR INTAKE FILTER:

A. Follow steps A and B above.

“

T

O

CHANGE SYSTEM

F

I

L

T

ER

”

.

B. Gently pull out the filter from the bottom.

C. Wash the filter with water.

D. Reinstall the filter, by sliding it into the

retaining rail.

E. Replace the access door and turn the

power on to the unit.

2. Keep the outdoor coil clean. Wash it

down with a garden hose if necessary.

REV. 10/26/16

2

678628-W

BE SURE THE UNIT DISCONNECT IS IN THE “OFF” POSITION

AND THAT ALL ELECTRICAL POWER TO THE UNIT IS

TURNED OFF BEFORE CLEANING THE SYSTEM.

Remove any loose grass, leaves, papers, etc., from the area

around the condenser coil. These could reduce the air supply

through the coil and reduce the amount of cooling capacity.

3. Since the air conditioner is located outdoors, it is exposed to all

weather elements. Treat it with a good automobile paste wax

twice a year (in the spring and fall).

Check with your contractor if you have any questions regarding

the maintenance or operation of your unit.

INSTALLATION

A. CODES

The installer SHALL comply with all local, state, and federal codes

and/or regulations pertaining to this type of equipment and its

installation. Such codes and/or regulations should take

precedence over any recommendations contained herein.

Installations SHALL be made in accordance with the National

Electrical Code, local codes, and recommendations made by the

National Board of Fire Underwriters.

B. UNIT SITE SELECTION

1. To eliminate noise from being transmitted into noise

sensitive areas, the unit should NOT be installed on walls

adjoining bedrooms, sleeping quarters, or adjacent to

windows.

5. Return and supply grilles must be used when the return

and supply are not ducted. When a supply grille is used

in the installation, the louver spacing must be no greater

than 5/8 inch.

6. If the factory-installed filter is used on your installation,

access to the filter is made through the center panel on the

front of the unit.

IF A REMOTE FILTER IS USED, SUCH AS A FILTER GRILLE,

THE FACTORY-INSTALLED FILTER MUST BE REMOVED AND

DISCARDED.

D. DUCTWORK

1. Properly-sized duct systems are critical for satisfactory

operation of any air conditioning system. All ductwork

MUST be correctly sized for the design air flow requirement

of the equipment.

2. The recommended operation duct static is to deduct 0.07"

W.C. for any size of heater 5 kW to 20 kW on factory or

field-installed heaters.

3. Ductwork routed through wall cavities, as well as any duct

not in conditioned space, MUST be insulated. Supply

ducting routed through exterior walls MUST be insulated

with 1" insulation to the back of the unit.

4. Supply and return air ducts should be flush with the exterior

wall and sized to fit over the unit duct collars in order to

compress the collar air gasket.

5. If supply duct is flashed to the exterior of a building

constructed with combustible material, the flashing MUST

be insulated in order to maintain the required clearances

to combustible materials. Required clearance is 1/4" for

the first three (3) feet of supply duct.

E. FILTERS

2.

Lo

c

a

t

i

n

g

th

e

un

it

a

s

c

l

o

s

e

a

s

po

ss

i

b

le

t

o

t

h

e

m

a

in

d

u

c

t

system or area to be conditioned, will prevent lengthy duct 1. One-inch disposable filters are supplied standard in each

3.

runs and unnecessary thermal and air-pressure losses.

Th

e

c

l

ea

ra

n

c

e

t

o

c

o

m

b

u

st

i

b

l

e

s

is

0

"

o

n

a

ll

s

i

de

s

,

an

d

1

/

4

"

un

i

t

.

Tw

o

-

i

n

c

h

d

i

s

po

s

ab

le

f

il

t

e

r

s

c

a

n

a

l

s

o

b

e

u

s

e

d

an

d

a

r

e

available as an option. The filter rack is adjustable to

4.

for the first three (3) feet of supply duct.

Th

e

co

nd

e

n

s

e

r

a

ir

i

n

l

e

t

s

(

l

e

ft

,

r

i

gh

t

an

d

b

o

tt

o

m

i

n

l

e

ts

)

a

cc

o

m

moda

t

e

2

"

f

il

t

e

rs

.

T

h

e

f

i

l

t

e

r

ac

k

o

n

t

h

is

s

e

r

i

e

s

i

s

adapted by bending the retaining brackets. Refer to the

5.

SHALL be located at least 8" away from walls or other

obstructions for unrestricted airflow.

Th

e

c

on

d

en

s

e

r

a

i

r

ou

t

l

e

t

s

hou

l

d

b

e

l

o

c

a

t

e

d

a

t

l

ea

s

t

6

’

awa

y

2.

M

a

i

n

t

en

a

n

c

e

s

e

ct

i

o

n

f

o

r

t

h

e

p

r

o

c

edu

r

e

s

f

o

r

c

h

a

ng

i

n

g

t

h

e

filters.

If a filter grille is used in the installation, the filter should be

from any obstructions to prevent recirculation of condenser

p

r

ope

r

ly

s

i

ze

d

t

o

a

ll

o

w a m

a

x

i

m

u

m

ve

l

o

c

i

t

y

o

f

40

0

FP

M.

air.

6. Bottom of the unit SHALL be located at least 12" away from

the ground or other obstructions for unrestricted airflow.

W

HE

N

US

I

N

G

A

F

I

L

T

E

R

GR

I

LLE

,

T

H

E

F

A

C

T

OR

Y

-

I

NS

T

A

LL

E

D

FILTER MUST BE REMOVED.

7.

Se

r

v

i

c

e

c

l

ea

r

an

c

e is

28

"

fr

o

m

t

h

e

l

e

ctr

i

c

a

l

b

o

x

a

cc

e

s

panel located on the front of the unit and 28" from the F. ELECTRICAL POWER

c

en

t

e

r

,

uppe

r

,

an

d l

owe

r

fr

on

t

a

cc

e

s

pane

l

s

.

The installer MUST check available power to make certain it

8.

Th

e

w

a

ll

s

e

l

e

ct

e

d

f

o

r

un

it

i

n

s

t

a

ll

a

t

i

o

n M

US

T

b

e

ab

le

t

o

r

b

e

matches the unit nameplate rating and that constant voltage can

m

a

d

e

t

o

s

a

f

e

ly

s

uppo

r

t

h

e

we

i

g

h

t

o

f

t

h

e

un

i

t

.

be maintained to the unit. Unsatisfactory and unsafe performance

9.

D

o

NO

T

l

o

c

a

t

e

w

he

r

e

h

e

a

t

,

li

n

t

o

r

e

xhau

s

t

f

u

m

e

s

w

ill

b

e

could otherwise result. The local power company should be

d

i

sc

ha

r

ge

d

o

n

t

h

e

u

n

it

(

a

s

f

r

o

m

d

r

ye

r

ven

ts)

.

contacted about questions concerning power supply.

C. UNIT PREPARATION

1. The V Series model units have top rain flashing built onto

the unit. The bottom-mounting flange for all models is

shipped

se

p

a

r

a

t

e

l

y and

i

n p

l

a

c

e

. (

R

e

f

e

r to

“

S

e

c

t

i

on

J. U

n

i

t

I

n

s

t

a

ll

a

t

i

on

”

for

the

recommended use

of

the

bo

tt

o

m

flange.)

2. Electrical entrances are located on the right side, left side,

and back of all V

S

e

r

i

es

un

i

t

s

.

R

e

f

e

r to

“

Section H.

Electrical Hook-

up

”

for

d

e

t

a

il

s

.

3. Bend the lids of return and supply opening to form return

and supply air collars and install air gaskets.

4. The supply and return air ducts should be checked to be

sure they:

a. Match the openings on the unit to be installed.

b. Have the same distance between them vertically as

the openings on the unit to be installed.

G. BREAKER/DISCONNECT ASSEMBLY

These units are standard equipped from the factory with a unit

disconnect. This is in the form of a circuit breaker (230V models)

or disconnect (460V models). If an optional electric heat kit is to be

installed, follow the instructions included with the heater assembly.

See Figure 1 for reference.

REV. 10/26/16

3

678628-W

WARNING: ELECTRICAL EQUIPMENT

SHOULD BE INSTALLED BY A QUALIFIED,

LICENSED ELECTRICIAN. IMPROPER

ELECTRICAL HOOK-UP MAY DAMAGE

EQUIPMENT, CAN CREATE A HAZARD AND WILL VOID

WARRANTY.

H. ELECTRICAL HOOKUP

The line voltage electrical service can be routed through the right

side panel, the right side of the back panel, or left side panel. Each

area is supplied with two line voltage knock-outs (1/2" – 3/4" and

1" – 1¼"). Low voltage wiring can be routed through the right or left

side panel.

NOTE: When routing line voltage through the return air

compartment, conduit MUST be used (even though this is a dry

area) to comply with the NEC code. A 11/4" conduit is supplied

for this application. Refer to the ELECTRICAL DATA tables for

minimum wire size and maximum breaker size. All wire sizes listed

under the dual-feed circuit column are based on no more than

three (3) conductors in the same conduit. If two circuits or more

than three (3) conductors are to be routed in the same conduit, the

ampacity of the wire size listed MUST be derated. Refer to Article

310 of the NEC code for adjustment factors. Be sure to install a

ground wire of the proper

s

i

z

e

to the

un

i

t

’

s

e

qu

i

pmen

t ground

l

ug.

I. LOW VOLTAGE WIRING

230 volt, 1- and 3-phase units are equipped with dual-primary

voltage transformers for 208/240 volt operation. These models are

factory wired to the 240 volt tap. For 208 volt operation connect the

factory-installed black wires from the 240 volt tap to the 208 volt

tap. The acceptable voltage range of the tap is as follows.

Tap Voltage Range

240 Volt 253 - 216

208 Volt 220 - 187

Five (5) conductor thermostat wires should be run from the

thermostat location to the unit. Thermostat wire should be sized as

shown on the table below.

W

i

r

e

G

aug

e

M

a

x

im

u

m

L

e

ng

t

h

20

45'

18

60'

16

100'

14

160'

12

250'

Refer to wiring diagrams for connection details.

STAGING OF ELECTRIC HEAT

All V Series units with electric heat assemblies above 10 kW may

be wired for single or two-stage heat. These models come factory

wired for single-stage operation. For two-stage operation, remove

the jumper bar from between the W1 and E terminal. Wire the first-

stage heat to terminal W1. Wire the second-stage heat to terminal

E.

J. UNIT INSTALLATION

V SERIES UNITS ARE FOR USE IN SINGLE-STORY

BUILDINGS ONLY

1. As previously stated, the wall that the unit is to be installed

onto MUST be strong enough to support the unit under the

condition for which it will be used. For example, a unit to be

installed on a building that is intended to be transported will

require more wall strength than a unit installed at a

permanent site. Existing walls may need additional

reinforcement. NEVER RELY ON EXTERIOR SIDING OR

PLYWOOD TO SUPPORT THE UNIT. Figure 2 at right

represents a typical installation of a single-story stud wall at

a permanent site. Since building materials and techniques

vary with regions and intended use, a building contractor

and/or local building code official MUST be consulted for

suitable construction methods.

2. Locate and attach the lower mounting bracket in the

desired location on the building.

3. Apply a suitable amount of caulk or silicone across the

entire length of the top rain flashing and side mounting

flanges.

4. Remove the flanges on both ends of the pallet and slide the

un

i

t

a

pp

r

o

x

i

m

a

t

e

l

y

2

”

off

the rear

of

pallet. Lift unit gently

into location with fork truck, taking care to align unit with

lower mounting bracket.

5. While allowing a small portion of weight on the lower

bracket, push the unit against the wall and fasten

appropriately.

SPECIAL NOTES FOR UNIT INSTALLATION

1) Minimum 12” clearance at the bottom of the unit for

unrestricted airflow.

2)

Ensure the ambient temperature uniformity around unit

3)

Intake and discharge of the outdoor air flow must not be

restricted or altered.

4)

All insulation and sealing related to the installation must

be completed properly

K. CONDENSATE DRAIN

A

3

/

4

”

d

r

a

i

n

hose

i

s

l

oc

a

t

e

d

on the bottom

s

i

d

e

of

the unit. The

drain may be extended for condensate removal to comply with

local codes (use fitting size or larger). Install a condensate trap on

this line.

L. AVAILABLE OPTIONS

Eubank wallmount air conditioners and heat pumps have the

ability to equip a variety of options:

Electric Heat 5-20kW Energy

Recovery Ventilator Sound

Attenuation Module Powered

Ventilation Damper

Low Ambient Packages

Economizer

Lead Lag Controllers

Option kits must be installed according to the respective

installation manual to ensure safe and reliable operation.

Installation manuals are included with the option kit or can be

found on the Eubank website, www.EubankNCC.com.

REV. 10/26/16 4

678628-W

5) External Static pressure should not exceed the minimum

value in the AHRI Standard 390

EXPLODED PAATS DRAWi NG - 18 / 24 / 30 / 36

REV. 10/26/16

5

678628-W

EXPLODED PARTS DRAWING -

48/60

REV. 10/26/16

6

678628-W

V Series AC Electrical Data

MODEL NO.

& ELECTRIC

HEATER kW

[1]

VOLT/

PHAS

E 60

Hz

NO. OF

FIELD

POWER

CKTS.

SINGLE-FIELD CIRCUIT DUAL-FIELD CIRCUIT

MCA MOP

[2]

FIELD POWER

WIRE

SIZE

[3]

GROUND

WIRE

SIZE

[3]

MCA

MOP

[2]

FIELD

POWER

WIRE SIZE

[3]

GROUND

WIRE

SIZE

[2]

CKT1 CKT2 CKT1 CKT2 CKT1 CKT2 CKT1 CKT2

V418B00A

5

10 208-230/1 1

1

14

29

55

20

30

60

14

10

6

14

10

V424B00A

5

10

208-230/1 1

1

19

29

55

30

60

14

10

6

10

V424B00A

6

9

208-230/3 1

1

13

20

30

20

25

40

14

12

10

12

10

V430B00A

5

10

208-230/1

1

24

30

56

40

60

12

10

6

10

V430B00A

6

9

208-230/3

1

17

22

30

25

40

14

12

10

V436B00A

5

10

15

208-230/1

1

2

26

30

56

40

60

10

6

10

26 52 30 60 10 610 10

V436B00A

6

9

15

208/230/3

1

20

22

30

49

30

40

50

12

10

8

10

V436B00A

6

9

15

460/3

1

10

16

15

20

30

14

10

14

12

10

V448B00A

5

10

15

208-230/1

1

2

33

58

50

60

10

6

10

27

52 30 60 10 610 10

V448B00A

6

9

15

18

208-230/3

1

24

33

50

60

30

40

60

70

12

10

6

10

8

V448B00A

6

9

15

460/3

1

10

13

17

15

20

30

14

12

10

V460B00B

5

10

15 208-230/1

1

2

39

58

60

8

6

10

33

52

40

60 10 610 10

V460B00B

6

9

15

18

208-230/3

1

26

33

50

60

40

60

70

10

6

10

8

V460B00B

6

9

15

460/3

1

13

17

26

20

30

14

10

12

10

25

26

7

PART NUMBER DESCRIPTION V418B1 V424B1 V430B1 V430B3 V436B1 V436B3 V436B4 V448B1 V448B3 V448B4 V460B1 V460B3 V460B4

2 COMP-L18-001 H62J18BABCA

2 COMP-L24-001 H82J24BABCA

2 COMP-L30-001 H82J28BABCA

2 COMP-L36-001 H82J35BABCA

2 COMP-BZP16-001 ZP16K5EPFV130 X

2 COMP-BZP24-001 ZP24K5EPFV130 X

2 COMP-BZP28-001 ZP28K5EPFV130 X

2 COMP-BZP28-003 ZP28K5ETF5130 X

2 COMP-BZP34-001 ZP34K5EPFV130 X

2 COMP-BZP34-003 ZP34K5ETF5130 X

2 COMP-BZP34-004 ZP34K5ETFD130 X

2 COMP-BZP44-001 ZP44K5EPFV130 X

2 COMP-BZP44-003 ZP44K5ETF5130 X

2 COMP-BZP44-004 ZP44K5ETFD130 X

2 COMP-BZP54-001 ZP57K5EPFV130 X

2 COMP-BZP54-003 ZP57K5ETF5130 X

2 COMP-BZP54-004 ZP57K5ETFD130 X

7 COND-V424 COND COIL X X

7 COND-V436 COND COIL X X X X X

7 COND-V460 COND COIL X X X X X X

8 550510 FLOWRATOR 4 CIRCUIT-COND X

8 550505 FLOWRATOR 3 CIRCUIT-COND X X X X X X

8 550517 FLOWRATOR 6 CIRCUIT-COND X X X X X X

14 EVAP-VH424 EVAP COIL X X

14 EVAP-VH436 EVAP COIL X X X X X

14 EVAP-VH460 EVAP COIL X X X X X X

15 550510 FLOWRATOR 4 CIRCUIT-EVAP X

15 550517 FLOWRATOR 6 CIRCUIT-EVAP X X X X X X

15 550521 FLOWRATOR 9 CIRCUIT-EVAP X X X X X X

550536 RESTRICTOR .063 X X

550531 RESTRICTOR .065 X X

550538 RESTRICTOR .070 X X X

550550 RESTRICTOR .094 X X X

550548 RESTRICTOR .096 X X X

061507 FILTER DRIER X X X X X X X

061508 FILTER DRIER X X X X X X

3 2021-5008 FAN SHROUD V18-24 X X

3 2022-5008 FAN SHROUD V30-36 X X X X X

3 2023-5008 FAN SHROUD V48-60 X X X X X X

4 259108 MOTOR MOUNT CONDENSER FAN X X X X X X X

4 259109 MOTOR MOUNT CONDENSER FAN X X X X X X

5 0250-0025 MOTOR CONDENSER 230V 1/5 HP X X X X X X

5 351145 MOTOR CONDENSER 230V 1/2 HP X X X X

5 359100 MOTOR CONDENSER 460V 1/4 HP X

5 351146 MOTOR CONDENSER 460V 1/2 HP X X

6 0550-0009 FAN BLADE 20" V18-36 X X X X X X X

6 259114 FAN BLADE 22" V48-60 X X X X X X

9 2022-5000 ASSEMBLY LEFT SIDE PANEL V18-36 X X X X X X X

9 2023-5000 ASSEMBLY LEFT SIDE PANEL V48-60 X X X X X X

10 2021-5012 ASSEMBLY REAR PANEL V18-24 X X

10 2022-5012 ASSEMBLY REAR PANEL V30-36 X X X X X

10 2023-5012 ASSEMBLY REAR PANEL V48-60 X X X X X X

11 2021-5003 ASSEMBLY DIVIDER DECK V18-24 X X

11 2022-5003 ASSEMBLY DIVIDER DECK V30-36 X X X X X

11 2023-5003 ASSEMBLY DIVIDER DECK V48-60 X X X X X X

12 2021-5005 ASSEMBLY BLOWER PAN V18-24 X X

12 2022-5005 ASSEMBLY BLOWER PAN V30-36 X X X X X

12 2023-5005 ASSEMBLY BLOWER PAN V48-60 X X X X X X

13 2021-0006P ASSEMBLY DRAIN PAN V18-24 X X

13 2022-0006P ASSEMBLY DRAIN PAN V30-36 X X X X X

13 2023-5006 ASSEMBLY DRAIN PAN V48-60 X X X X X X

17 2021-5002 BASE PAN ASSEMBLY V18-24 X X

17 2022-5002 BASE PAN ASSEMBLY V30-36 X X X X X

17 2023-5002H BASE PAN ASSEMBLY V48-40 X X X X X X

22 2021-5018 BLOWER MNTG TRAY V18-24 X X

22 2022-5018 BLOWER MNTG TRAY V30-36 X X X X X

22 2023-5018-4 BLOWER MNTG TRAY V48 X X X

22 2023-5018-5 BLOWER MNTG TRAY V60 X X X

23 2022-5001 ASSEMBLY RIGHT SIDE V18-36 X X X X X X X

23 2023-5001 ASSEMBLY RIGHT SIDE V48-60 X X X X X X

23A 2023-5088 GRILL INLET RIGHT SIDE V48-60 X X X X X X

23B 2023-5089 GRILL INLET LEFT SIDE V48-60 X X X X X X

24 194700050002 BLOWER 9-7R DD 18, 24, & 48 CW RIGHT X X X X X

24 194700050004 BLOWER 10-7R DD 60 CW RIGHT X X X

24 0500-0010 BLOWER 10-10 DD 30 & 36 X X X X X

24A 1947000050001 BLOWER 9-7L DD 48 CCW LEFT X X X

24A 194700050003 BLOWER 10-7L DD 60 CCW LEFT X X X

25 351115 MOTOR BLOWER 1/6 HP 230V X X

25 194090000006 MOTOR BLOWER 1/3 HP 230V X X X X

25 020008 MOTOR BLOWER 1/2 HP double shaft 230V X X

25 351424 MOTOR BLOWER 3/4 HP double shaft 230V X X

25 359101 MOTOR BLOWER 1/3 HP 460V (2-3 ton) X

25 020005 MOTOR BLOWER 1/2 HP double shaft 460V X

25 351426 MOTOR BLOWER 3/4 HP double shaft 460V X

26 BLWR-MTG2B MOTOR MOUNT INDOOR ASSY V18-24 X X

26 258972 MOTOR MOUNT INDOOR ASSY V30-36 X X X X X

26 258976 MOTOR MOUNT INDOOR ASSY V48-60 X X X X X X

27 2021-5007 TOP V18-24 X X

27 2022-5007 TOP V30-36 X X X X X

27 2023-5007 TOP V48-60 X X X X X X

REPLACEMENT PARTS LIST - V SERIES WALLMOUNT A/C

8

2

8

2

0

2

1

-

5

010

T

OP

F

RONT

P

ANEL

V

l

B

-

2

4

x

)(

29

2021

-

5

011

T

OP

F

R

ONT

P

AN

E

L

Vt

B

-

2

5

)(

28 2

0

2

3-

5

0

1

0

T

O

P

F

RONTPAN

EL

V

48-60

x

29

2021

-

5

011

MI

D

DLE

F

RON

T

P

AN

EL

(no

fr

e

!h

aw

)

V

IB

-

2

4

x

29 2

0

2

1-

5

0

11EMIDDLE FRONT PANEL

(economizer I/a)

V

I

S

-

2

4

x

29

202

1-5

0

11F

MID

D

LEf

R

O

NT

PAN

E

L

(b

a

ro

m

et

ricf

/a)

VIB

-

24

x

2

9

2

022

-

5

011

M

I

D

DL

E

FRONT PANEL

{no

fre!h

airl

V3

0

-

3

6

x

2

9

2022

-

5

0

11

E

MID

D

LE

F

R

ONT

P

AN

EL

C

eco

n

om

iz

et

I

/

al

V3

0

-

36

)(

x

29

2022.50

u

FMIDDLE

F

R

ONT PANEL

(ba

ro

m

e

t

ricf

/a

)

V

30

·

36

x

)(

x

29

2023

-

5

011

MIDDLE

FRONT PANEL

(no fre!h alt)

V

48-60

x

29

2023

-

5011

EMIDDLE FRONT PANEL

(economi

z

or

f

/a

)

V

4

8

-60

x

29

2023

-

50

ll

F

MID

D

LE

F

R

ONT

P

AN

E

L

(ba

r

o

m

et

ri

c

I/

a

l

V

48

-

60

x

30

2021

-

5014

L

O

W

ER

COND

EN

SER

P

AN

EL

V

18

-

24

x

30

2022

-

5014 LOWER CONDENSERPANEL

V30-36

x

)(

3

0

2023

-

5014 LOWER CONDENSERPANEL V48-60

x

)(

31

2022

-

5062

DISCONNECT

ACCESS

DOO

R

V

lB-60

x

)(

x

)(

x

)(

31A

7

051

8

BREAXER

DOOR LATOi

V

I

B-60

x

32

659

94

2

AJ

R

FILTER

DISPOSABLE

1

6"2

Sx

l

V

lB

-

36

x

32 6

59

943

AIR

FILTER

DISPOSABLE

1

6"2

Sx

2

V

l

B-3

6

x

)(

x

)(

x

)(

32

6599

2

6

AJR

FILTER

D

ISPOSABLE

20.3

0.

1

V4

8-6

0

x

)(

x

)(

3

2

659924

AJR

FILTER

DISPOSABLE

20.30.2

V4

8-6

0

x

654

6

0

2

ALUMINUM FILTERSx30x.025

V

I

B-60

x

34

202

1

-

5

0

04 FILTERRAO(

V

lB-2

4

)(

x

34

2

022

-

5

0

04

FIL

T

ER

RA

O(

V30·

3

6

x

)(

x

)(

34

2

0

23

-

5

0

04

FIL

T

ER

RA

O(

V4

8

-

6

0

x

)(

3

5

2022

-

5

021

H

EA

T

ER

M

OU

N

TI

N

G

P

LA

TE

VlB

-

3

6

x

35

6

5

SM100

7

.f

HEATER MOUNTING PLATE

V4

8

-60

x

36

EG

A

05B

I

-A

C

FIELD

INSTAll

HEAT KIT 5KW I

P

H

A

SE

23

0V

x

)(

x

36

04

30

-

00

7

4

H

EAT

ER

5

K

W

I

P

2

4

0V

x

3

6

EG

A

IOB

I

-

A

C

F

I

ELD

I

NSTAil

H

EAT

K

I

T

I

OKW

I

PH

A

SE

230

V

x

36

04

3

0

.oon

HEA

T

ER

l

OK

W

I

P

2

4

0

V

x

36

EG

H

ISB

I

-

A

C

F

I

ELD

I

NSTAlLHEAT

K

IT

I

SK

Wl

PH

A

SE230

V

x

36

04

30

-

00

74

HEATER

5

KW

IP

240

V

x

36

04

3

0

.oon

HEATER

I

OK

W

I

P

2

40

V

x

36 EGH06B3..ACFIELDINSTAlL HEAT

K

I

T6

K

W

3

PHASE

230

V

x

36

4

580

0

9

HEATER 6KW 3P

240

V

x

36

E

G

H

11B3..AC

F

I

E

L

D

I

NS

T

All

HEAT

K

I

T

II

KW

3

PH

A

SE

230

V

x

36

4

58011

HEA

T

ER

ll

K

W

3P

2

4

0V

)(

x

3

6

EG

H

11!83

..A

C

F

I

E

L

D

INSTAll HEATKIT 18KW 3

PH

A

SE

2

3

0

V

x

36

4

58013

HEATER 18KW 3P 2

40

V

x

36

EGH

06

04

-AC FIELDINSTAil HEAT KIT 6KW3

P

H

A

SE

46

0

V

x

36

4

580

15

H

EA

TER

6

K

W

3

P

4

60

V

x

36

EG

H

11

D

4

-

AC

F

I

ELD

I

N

S

T

ALL

HEA

T

K

IT

II

KW3

P

H

ASE

4

6

0

V

x

36

4

5

80

1

7

H

EAT

ER

ll

K

W

3

P

4

60

V

x

36

EG

H

1504

-

AC

F

I

EL

D

I

N

S

T

ALL

HEAT

K

IT

15

K

W

3

PH

ASE

46

0

V

x

36

4

580

2

0

HEATER 15KW 3P

460V

x

37

2022

-H

EP

LHEATER

EXTENSION

PLATE

H

2

4

-36

x

37

20

23

-HEP

LHEATER EXTENSIONPLATE

H4

8

-60

x

38

4

543

3

2

SWITCH

ll

M

IT

245

F

ONE SHOT

x

3

8

4

54323

S

WIT

CH

LI

M

IT

1

60

-

30

F

2

40

W

/fUSE

x

39

2021

·

5009H

eo

x

CO

NT

ROL

V

IS

-

2

4

x

)(

39

2022

-

50

0

911

eox

CONTROL

V30

-

36

x

)(

x

39

2023

-

5009H

eox

CONTROL

V

48-60

x

40

2021

-

5017

COMP

R

ESSOR

A

CCESS

DOOR

V

l

S-2

4

x

)(

40

202

2-

5017

C

OMP

R

ESSOR

A

CCESS

DOOR

V30

·36

)(

40

2023

-

5017

COMP

R

ESSOR

A

CCESS

DOOR

V

4

8

-60

x

)(

x

4

1

2021

-

50

20

BL

OW

ER

OJT

OFF

SH

I

E

L

D

V

lB

-

2

4

x

41

2

022

-

50

20

BL

OW

ER

OJT

O

FF

SHIE

L

D

V30

-

3

6

)(

x

4

1

2023

-

5

0

20

-

4

B

L

O

W

ER

OUT

OFF

SHIELD

V48

)(

41

2023

-

5

0

20

-

5

BLOWER OUT OFF SHIELD

V6

0

x

)(

x

4

2

2022

-

0015

P

LA

T

E

TCP

I

NSUL

PR

DT

ECf

H/

V3

0

-

36

x

)(

x

)(

453

15

0

COMP

CONTACTOR

1POlf

!

P

25AMP

x

)(

453

770

COM

P

CON

T

Acr

O

R

2

P

Olf

IP

40AM

P

x

453

772

COMP

CON

TAcrOR 3 POlf 3P 25

AMP

x

)(

x

)(

x

)(

452

812

PHASE

M

O

NI

T

OR

x

)(

4

50362

CO

MP

CAP

A

OT

O

R

7

.S/3

5

@

3

7

0

040

0

-

00

3

1

CO

MP

CAPAO

TO

R

1

0/80

@3

7

0

x

4

5

0

36

8

COMP

CAPAOTOR 7

.

5/

4

0@

370

x

4

50

36

4

CO

M

P

CAPAOT

O

R

7

.

5/

4

0

@4

4

0

4

5

0

361

CO

MP

CAP

AO

TO

R

7

.

5/3

0@

3

7

0

x

450370

COMP CAP

AOT

O

R

7

.

5/

45

@3

70

x

450378

COMP CAPAOTOR 10

fl

0@3

7

0

x

4

50325

BLWR CAPAOTOR

10@3

7

0

)(

4

5

0

2

0

5

BL

WR

CAP

A

OTO

R

7

.5

@

370

x

)(

x

1605

00

7

301

4

5

BL

WR

CAP

A

O

T

O

R

7

.5@4

4

0

x

)(

4

510

0

T

ER

M

I

NAL Bl.CCX

)(

x

)(

x

4

52

7

52

TR

AN

SFOR

M

E

R

208/2

4

0

V

5

0

VA

2

4V

)(

4

52

75

6

T

RANS

FORME

R

4

80

V

SO

V

A

2

4V

)(

4

5

22

00

F

AN

R

E

LA

Y

)(

x

)(

x

0

82

lN

-

00

81A

F

AN

RE

LA

Y

)(

4

20

04

O

R

OJ

I

T BREAKER2 POLE IP 60 AMP

2

40V

x

)(

x

4

53

80

7

ORCU

I

T

BR

EAKE

R

3

P

O

LE

3

P

60

AM

P

)(

45

195

5

DISCONNECf

K

I

T

460V

x

4

519

5

6

OISCON

N

ECf

K

N

08

4

60

V

x

)(

0415

-002

8

LOW VOLTAGE

T

E

R

M

I

N

AL

B

O

AR

D

x

)(

x

)(

x

4

5

1

04

9

J

UM

P

ER

BAR

AS

SEMB

LY

O

PT

I

ON

AL

4

5

1

81

0

CP

TI

ON

S

ao.R

D

O

PT

I

ON

AL

4

54

3

8

LO

W

PRESSUR

E

SWITOi

ST

AN

D

AR

D

O

N

Al

l

U

N

I

T

S

45

1

98

8

HIGH

PRESSURE

S

WIT

CH STANDARD ON

Al

l

UN

ITS

4

51992

FAN

CYQ.E

S

WI

TCH

O

PT

I

ON

AL

REV. 10/26/16

9

678628-W

14

NOTES

REV. 10/26/16 15678628-W

The information in this manual supersedes and replaces the previous instruction/operation manual 678628V with regards to T

Series wallmount products. Illustrations, part numbers and others cover the general appearance of the units at the time of

publication and the Manufacturer reserves the right to make changes in design and construction at any time without notice.

For replacement parts contact:

National Coil Company

1998 FM 2011

Longview, TX 75603

Phone: 903-643-2261

Fax: 903-643-2222

www.EubankNCC.com

REV. 10/26/16 16 678628-W

Eubank V SERIES Installation and operating instructions

Popular Air Conditioner manuals by other brands