EUCHIPS EUP10D-1HMC-0-120 User manual

EUP10D-1HMC-0-120(Product No.: 102100700201)
DALI Constant Current Dimming Driver
Summary
Product Feature
Touch DIM(Push DIM)
200VAC-240VAC
50/60Hz
82%@230VAC, Full load
0.95@230VAC, Full load
<0.5W
cold start,10A(twidth=10us measured at 50% Ipeak@230VACC
0.06Amax@230VAC, Full load
110*30*22.5mm(L*W*H)
60g
IP20
-20℃~50℃
-40℃~85℃, 20-90%RH
75℃
L-N:500V
I/P-O/P: 1500VAC
PC
50,000h@tc:75℃
1%-100%
50VDC
±5%
<3%
DALI /
>100,000 times
1
120mA/9-45VDC/5.4W
220mA/9-45VDC/9.9W
150mA/9-45VDC/6.75W
250mA/9-40VDC/10W
170mA/9-45VDC/9.9W
270mA/9-37VDC/9.99W
200mA/9-45VDC/9W
300mA/9-33VDC/9.9W
<10%@230VAC, Full load
EUP10D-1HMC-0-120
Surge
Withstand Voltage
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI Standrad
tc
Lifetime
Material
Dimming Range
Dimension
515*235*140mm(L*W*H), 9.5Kg/Carton/100PCS
Packing Size
G.W
IP Rating
Working Temp.
Storage Temp.; Humidity
Dimming Mode
Switch Cycle
5 yearsWarranty Condition
No Load Output Voltage
Turn On Delay Time <1s, at 230Vac
Efficiency
Standby Power
Current
Inrush Current
THD
Current/voltage/power
Ripple Current
Channel
Current Tolerance
Voltage
Frequency
Power Factor
No Load
Short Circuit
Over Load
The LED Driver will not be damaged.
Hiccup mode, recovers automatically after fault condition is removed
No Output, recovers automatically after fault condition is removed
Safety
Others
Function
Model
Output
Input
Protection
Technical Parameters
1/2
User’s manual: 2019-8 www.euchips.com
Current Selection Table
Remark: Function default setting is: 120mA (@switch are all OFF state)
120mA 150mA 170mA
9-45V 9-45V
200mA
9-45V9-45V
ON OFF 220mA
9-45V
250mA
9-40V
270mA
9-37V
300mA
9-33V
EUP10D-1HMC-0-120 is a 10W AC/DC constant current mode output LED driver featuring the multiple levels
selectable by DIP switch and complies with DALI standard protocol IEC 62386. EUP10D-1HMC-0-120 can be
connected to DALI main controller or Touch DIM(Push DIM) to achieve a smooth dimming effect.
·Single channel output, output current level selectable by DIP S.W.
·Meet DALI Protocol IEC 62386-207
·Support Touch DIM (Push DIM)function
·High efficiency up to 82%
·Built-in active PFC function
·Dimming effect smooth, no flicker
·Protections: Short circuit, over load, no load
·Suitable for indoor LED lighting application, such as down light, spot light, and so on

Dimension(mm) Wiring Diagram
22.6
110.0
29.6
EUP10D-1HMC-0-120
L
N
DA1
DA2
OUTPUT
LED -
LED+
220-240VAC
Input
DALI Master
Lamp
DALI Constant Current Dimming Driver
2/2
User’s manual: 2019-8 www.euchips.com
Push DIM(Touch DIM) Diagram
Push DIM Function
1. Press the Touch DIM switch for 8s or more,the driver can be controlled via Touch DIM switch.
2. Short press the Touch DIM switch (<0.5s) to control the lamp on or off.
3. Long press the Touch DIM switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Touch DIM switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long
pressing Touch DIM switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
DALI Wiring Diagram
Remarks: use only open push switch (without indicator light). When using synchronous connection, the line length between each device and equipment shall not exceed 20 meters.
DALI Driver 1
DA
DA LED-
LED+
L
N
DALI Driver 2
DA
DA LED-
LED+
L
N
L
N
DALI Controller
DALI Driver 1
DA
DA LED-
LED+
L
N
DALI Driver 2
DA
DA LED-
LED+
L
N
Push DIM Pannel(Touch DIM)
LN
※The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions, the function of the product shall prevail.Please contact us if you have any
questions .
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75- 1.5mm²is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
Derating CurveDimming Curve PF VS Load
Eff. VS LoadTHD VS load
Ambient Temperature(℃)
Load (%)
0
20
40
60
80
100
-20 -10 10 20 30 40 50 600
Output (%)
Input signal(%)
0
0
4
14
2 1 29
36 43
50 5 7
64
7 1 78
85
92
100
20
40
60
80
100
Load (%)
THD(%)
THD
060 70 80 90 100
2
4
6
8
10
12
Load (%)
PF
0.97
0.965
0.96
0.955
0.95
0.945
60 70 80 90 100
230Vac
Load (%)
Efficiency(%)
70.00
75.00
80.00
85.00
90.00
95.00
60 70 80 90 100