Siemens SIMATIC ET 200SP Technical Document

CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
SIMATIC
ET 200SP
CPU 1510SP
-1 PN
(6ES7510
-1DJ01-0AB0)
Equipment Manual
05/2021
A5E03506268
-AD
Preface
ET 200SP Documentation
Guide
1
Product overview
2
Wiring
3
Interrupts, error messages,
diagnostics and system
alarms
4
Technical specifications
5
Dimension drawing
A

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E03506268-AD
Ⓟ
05/2021 Subject to change
Copyright © Siemens AG 2014 - 2021.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 3
Preface
Purpose of the documentation
This manual supplements the ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293) system manual as well as
the function manuals. This manual contains a description of the module-specific information.
The system-related functions are described in the system manual. All system-spanning
functions are described in the function manuals.
The information provided in this manual and the system manual allows you to commission
the CPU 1510SP-1 PN.
Conventions
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
Please also observe the notes marked as follows:
Note
A note con
tains important information on the product described in the documentation, on
the handling of the product or on the section of the documentation to which particular
attention should be paid.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (https://www.siemens.com/industrialsecurity).

Preface
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
4Equipment Manual, 05/2021, A5E03506268-AD
Siemens Industry Online Support
You can find current information on the following topics quickly and easily here:
•Product support
All the information and extensive know-how on your product, technical specifications,
FAQs, certificates, downloads, and manuals.
•Application examples
Tools and examples to solve your automation tasks – as well as function blocks,
performance information and videos.
•Services
Information about Industry Services, Field Services, Technical Support, spare parts and
training offers.
•Forums
For answers and solutions concerning automation technology.
•mySupport
Your personal working area in Industry Online Support for messages, support queries, and
configurable documents.
This information is provided by the Siemens Industry Online Support in the Internet
(http://www.siemens.com/automation/service&support).
Industry Mall
The Industry Mall is the catalog and order system of Siemens AG for automation and drive
solutions on the basis of Totally Integrated Automation (TIA) and Totally Integrated Power
(TIP).
Catalogs for all the products in automation and drives are available on the Internet
(https://mall.industry.siemens.com).

CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 5
Table of contents
Preface ................................................................................................................................................... 3
1 ET 200SP Documentation Guide ............................................................................................................ 6
2 Product overview................................................................................................................................. 11
2.1 New functions ................................................................................................................... 11
2.2 Operating principle............................................................................................................ 13
2.3 Properties.......................................................................................................................... 14
2.4 Operating and display elements ......................................................................................... 19
2.4.1 Front view of the module with BusAdapter......................................................................... 19
2.5 Mode switch...................................................................................................................... 20
3 Wiring .................................................................................................................................................. 21
4 Interrupts, error messages, diagnostics and system alarms ............................................................... 25
4.1 Status and error display of the CPU..................................................................................... 25
5 Technical specifications....................................................................................................................... 28
A Dimension drawing ............................................................................................................................. 42

CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
6Equipment Manual, 05/2021, A5E03506268-AD
ET 200SP Documentation Guide
1
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
Basic information
The System Manual and Getting Started describe in detail the configuration, installation,
wiring and commissioning of the SIMATIC ET 200SP distributed I/O system. The STEP 7 online
help supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.

ET 200SP Documentation Guide
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 7
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, motion
control and OPC UA.
You can download the documentation free of charge from the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109742709).
Changes and supplements to the manuals are documented in a Product Information.
You can download the product information free of charge from the Internet
(https://support.industry.siemens.com/cs/us/en/view/73021864).
Manual Collection ET 200SP
The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(https://support.automation.siemens.com/WW/view/en/84133942).
"mySupport"
With "mySupport", your personal workspace, you make the best out of your Industry Online
Support.
In "mySupport", you can save filters, favorites and tags, request CAx data and compile your
personal library in the Documentation area. In addition, your data is already filled out in
support requests and you can get an overview of your current requests at any time.
You must register once to use the full functionality of "mySupport".
You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en).
"mySupport" - Documentation
With "mySupport", your personal workspace, you make the best out of your Industry Online
Support.
In "mySupport", you can save filters, favorites and tags, request CAx data and compile your
personal library in the Documentation area. In addition, your data is already filled out in
support requests and you can get an overview of your current requests at any time.
You must register once to use the full functionality of "mySupport".
You can find "mySupport" on the Internet
(https://support.industry.siemens.com/My/ww/en/documentation).

ET 200SP Documentation Guide
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
8Equipment Manual, 05/2021, A5E03506268-AD
"mySupport" - CAx data
In the CAx data area of "mySupport", you can access the latest product data for your CAx or
CAe system.
You configure your own download package with a few clicks.
In doing so you can select:
•Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
•Manuals, characteristics, operating manuals, certificates
•Product master data
You can find "mySupport" - CAx data on the Internet
(https://support.industry.siemens.com/my/ww/en/CAxOnline).
Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus on individual products.
You will find the application examples on the Internet
(https://support.industry.siemens.com/cs/ww/en/ps/ae).
TIA Selection Tool
With the TIA Selection Tool, you can select, configure and order devices for Totally Integrated
Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109767888).

ET 200SP Documentation Guide
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 9
SIMATIC Automation Tool
You can use the SIMATIC Automation Tool to perform commissioning and maintenance
activities simultaneously on various SIMATIC S7 stations as a bulk operation independent of
TIA Portal.
The SIMATIC Automation Tool provides a multitude of functions:
•Scanning of a PROFINET/Ethernet system network and identification of all connected CPUs
•Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a CPU
•Transfer of the date and the programming device/PC time converted to UTC time to the
module
•Program download to CPU
•RUN/STOP mode switchover
•CPU localization by means of LED flashing
•Reading out of CPU error information
•Reading of the CPU diagnostics buffer
•Reset to factory settings
•Firmware update of the CPU and connected modules
You can find the SIMATIC Automation Tool on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/98161300).
PRONETA
SIEMENS PRONETA (PROFINET network analysis) allows you to analyze the plant network
during commissioning. PRONETA features two core functions:
•The topology overview automatically scans the PROFINET and all connected components.
•The IO check is a fast test of the wiring and the module configuration of a plant, incl. fail-
safe inputs and outputs.
You can find SIEMENS PRONETA on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/67460624).

ET 200SP Documentation Guide
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
10 Equipment Manual, 05/2021, A5E03506268-AD
SINETPLAN
SINETPLAN, the Siemens Network Planner, supports you in planning automation systems and
networks based on PROFINET. The tool facilitates professional and predictive dimensioning of
your PROFINET installation as early as in the planning stage. In addition, SINETPLAN supports
you during network optimization and helps you to exploit network resources optimally and to
plan reserves. This helps to prevent problems in commissioning or failures during productive
operation even in advance of a planned operation. This increases the availability of the
production plant and helps improve operational safety.
The advantages at a glance
•Network optimization thanks to port-specific calculation of the network load
•Increased production availability thanks to online scan and verification of existing systems
•Transparency before commissioning through importing and simulation of existing STEP 7
projects
•Efficiency through securing existing investments in the long term and the optimal use of
resources
You can find SINETPLAN on the Internet (https://www.siemens.com/sinetplan).

CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 11
Product overview
2
2.1 New functions
New functions of the CPU in firmware version V2.9
The following table provides an overview of the most important new functions of the CPU
with firmware version V2.9.
New functions Applications Customer benefits Where can I find in-
formation?
Communication of the CPU
Secure PG/HMI communi-
cation
With STEP 7 and WinCC as of Version
V17, SIMATIC S7-1500 CPUs and ET
200 CPUs from firmware version 2.9
support innovated and standardized
secure PG/PC and HMI communica-
tion – referred to as Secure PG/HMI
communication for short.
Secure and standardized crea-
tion or assignment of PLC
communication certificates
Communication func-
tion manual
(https://support.industr
y.siemens.com/cs/ww/
en/view/59192925)
Protection of confidential
configuration data
You have the option of assigning a
password for protecting confidential
configuration data of the respective
CPU. This refers to data such as pri-
vate keys that are required for the
proper functioning of certificate-
based protocols.
Additional password protec-
tion of confidential configura-
tion data
OPC UA: Alarms & Condi-
tions
OPC UA clients from any manufactur-
er can subscribe to alarms of the CPU
via OPC UA Alarms & Conditions.
Without further measures,
alarms created once via OPC
UA are available as events and
alarms. The alarms can be
displayed by any display de-
vice with corresponding OPC
UA client functionality.
OPC UA: Certificate man-
agement via Global Dis-
covery Server (GDS)
Via GDS push management func-
tions:
•Automated update of OPC UA
certificates of an S7-1500 CPU
•Transfer of updated certificates
and lists in RUN operating state of
the CPU
The automation of the certifi-
cate management eliminates
any manual work required for
reconfiguring the CPU, for
example, after a certificate has
expired, and a new download
to the CPU.

Product overview
2.1 New functions
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
12 Equipment Manual, 05/2021, A5E03506268-AD
New functions Applications Customer benefits Where can I find in-
formation?
DHCP (Dynamic Host
Configuration Protocol)
The CPU can use the DHCP communi-
cation protocol to assign the network
configuration via a DHCP server.
The CPU uses a client ID for identifi-
cation on the DHCP server.
The following parameters can be
obtained:
•IP Suite
•DNS server
•NTP server
The CPU can also send its host name
to the DHCP server.
With DHCP, you can integrate
the CPU into an existing IT
network without having to
make additional changes to
the PROFINET interface.
Communication func-
tion manual
(https://support.industr
y.siemens.com/cs/ww/
en/view/59192925)
MRP interconnection in
PROFINET networks
The MRP interconnection procedure
is an extension of MRP.
MRP interconnection enables the
redundant coupling of two or more
rings with MRP in PROFINET net-
works.
There is no limit to the maxi-
mum number of 50 devices in
a ring when setting up redun-
dant network topologies.
Monitoring of larger topolo-
gies with ring redundancy
PROFINET function
manual
(https://support.industr
y.siemens.com/cs/ww/
en/view/49948856)
Web server of the CPU
Web applications that can
be loaded by the user
Additional methods to manage web
applications via Web API
You can use all available Web API
methods within the web application
Web applications are also
available in STOP mode of the
CPU
Reduced development times
of web server user pages
Web server function
manual
(https://support.industr
y.siemens.com/cs/ww/
en/view/59193560)
New Web API methods
Reading and changing the CPU oper-
ating state via Web API
Ticket methods for transferring large
amounts of data outside of the JSON
RPC protocol
Additional applications for the
web server
Diagnostic information on
motion control
Diagnostic information is available
for all technology objects
Improved display and grouping of the
tags
Comprehensive diagnostic
options by means of motion
control applications are possi-
ble via the web server.
Optimizations to the DNS
(Domain Name System)
functionality with OPC
UA/Open User Communi-
cation and on the web
server
The feedback messages of the OPC
UA server with the "Application
Name" can be sent via DNS.
The NTP client of the CPU can address
its relevant NTP servers via DNS.
The Web server can be consistently
reached via DNS addressing. DNS is
taken into account during certificate
handling.
A pool of NTP servers can be
addressed.
Communication func-
tion manual
(https://support.industr
y.siemens.com/cs/ww/
en/view/59192925)
Web server function
manual
(https://support.industr
y.siemens.com/cs/ww/
en/view/59193560)
Technology functions of the CPU
Axis functions
•Backlash compensation
•Linear motor
The repeat accuracy of a
movement is increased by
compensation for the mechan-
ical play of the real axis.
Easier control of highly dy-
namic linear motors.
S7-1500T Motion Con-
trol function manuals
(https://support.industr
y.siemens.com/cs/ww/
en/view/109751049)

Product overview
2.2 Operating principle
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 13
Reference
You can find an overview of all new functions, improvements and revisions in the respective
firmware versions on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109478459).
2.2 Operating principle
The CPU contains the operating system and executes the user program. The user program is
located on the SIMATIC memory card and is processed in the work memory of the CPU.
The PROFINET interfaces on the CPU allow simultaneous communication with PROFINET
devices, PROFINET controllers, HMI devices, programming devices, other controllers and
other systems. The CPU 1510SP-1 PN supports operation as an IO controller, I-device or
standalone CPU.
With its optional PROFIBUS interface, CM DP, CPU 1510SP-1 PN supports the configuration of
PROFIBUS networks in addition to PROFINET IO. When you use the interface as a PROFIBUS DP
interface, you can configure the CPU 1510SP-1 PN as a DP master or as an intelligent DP slave
(I-slave).
IO controller
CPU 1510SP-1 PN sends and receives data from the connected IO devices within a
PROFINET IO system. You can operate the CPU with a maximum of 64 connected IO devices, a
maximum of 64 of which use IRT (Isochronous Real Time).
I-device
The "I-device" (intelligent IO device) functionality allows you to exchange data with an IO
controller. CPU 1510SP-1 PN thus fulfills the role of an intelligent distributed pre-processing
unit for sub-processes. The I-device is connected as an IO device to a higher-level IO
controller for this purpose.
Advantages:
•Interference-resistant configuration due to short signal and encoder wiring
•Reduced wiring requirements for transmission of the data via PROFINET
Standalone CPU
You can also use the CPU 1510SP-1 PN in the ET 200SP distributed I/O system as a "central
system" without a higher-level controller.
DP master
To use the ET 200SP as a DP master, you need the CPU and the optional communication
module, CM DP. When used as a DP master, ET 200SP exchanges data with the connected DP
slaves via PROFIBUS DP.

Product overview
2.3 Properties
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
14 Equipment Manual, 05/2021, A5E03506268-AD
Intelligent DP slave (I-slave)
To use the ET 200SP as an intelligent DP slave (I-slave), you need the CPU and the optional
communication module, CM DP. As an I-slave, the ET 200SP CPU is connected via PROFIBUS
DP to a higher-level DP master and exchanges data with it.
2.3 Properties
Article number
6ES7510-1DJ01-0AB0
View of the module
The following figure shows the CPU 1510SP-1 PN.
Figure 2-1 CPU 1510SP-1 PN

Product overview
2.3 Properties
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 15
Properties
The CPU 1510SP-1 PN has the following technical properties:
•Communication:
–Interfaces
The CPU 1510SP-1 PN has a PROFINET interface (X1 P3) with an integrated 3-port
switch. Port 1 and port 2 are located on the optionally pluggable BusAdapter. Port 3 is
integrated in the housing of the CPU. The CPU supports the BusAdapters BA 2xRJ45
and BA 2xFC. You connect the PROFINET IO to the CPU via the BusAdapter.
In addition to PROFINET basic functionality, the interface also supports PROFINET IO RT
(real-time) and IRT (isochronous real-time). PROFINET IO communication or real-time
settings can be configured. The basic functionality of PROFINET supports HMI
communication, communication with the configuration system, communication with a
higher-level network (backbone, router, Internet) and communication with another
machine or automation cell.
Port 1 and port 2 can also be used as ring ports for the configuration of redundant ring
structures in Ethernet.
Note
The CPU is delivered without a BusAdapter. You can find the article numbers of the
supported BusAdapters in the "Accessories/spare parts" section of the ET
200SP
distributed automation system
(http://support.automation.siemens.com/WW/view/en/58649293) system manual.
The CM DP is optionally available with a PROFIBUS interface (X2). You can find
additional information about this expansion module in the manual Communication
module CM DP (http://support.automation.siemens.com/WW/view/en/90156526).
You can find information about connecting the PROFINET IO BusAdapter to the CPU as
well as connecting the optional PROFIBUS interface to the interface module in the
system manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
–OPC UA
With OPC UA, data is exchanged via an open and vendor-neutral communication
protocol. The CPU, as OPC UA server, can communicate with OPC UA clients such as
HMI panels, SCADA systems, etc.
•Integrated Web server:
A Web server is integrated in the CPU. You can read out the following information with
the Web server:
–Start page with general CPU information
–Identification information
–Contents of the diagnostics buffer
–Query of module states
–Firmware update
–Alarms (without acknowledgment option)

Product overview
2.3 Properties
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
16 Equipment Manual, 05/2021, A5E03506268-AD
–Information about communication
–PROFINET topology
–Tag status, writing tags
–Watch tables
–Memory usage
–User pages
–Data logs (if used)
–Online backup and restoration of the configuration.
–Diagnostic information for the motion control technology objects
–Display of trace recordings stored on the SIMATIC memory card
–Readout service data
–Basic Web pages
–Display of the Web server in 3 project languages, for example, comments and message
texts
–Recipes
–User-defined Web pages
•Integrated technology:
–Motion Control
The Motion Control functionality uses technology objects to support speed-controlled
axes, positioning axes, synchronous axes, external encoders, cams, cam tracks and
measuring inputs, as well as PLCopen blocks for programming the motion control
functionality.
You can find a detailed description of the use of Motion Control and its configuration in
the S7-1500 Motion Control
(https://support.industry.siemens.com/cs/ww/en/view/109751049) function manuals.
–Integrated closed-loop control functionality
- PID Compact (continuous PID controller)
- PID 3Step (step controller for integrating actuators)
- PID Temp (temperature controller for heating and cooling with two separate
actuators)
•Trace functionality:
–Trace functionality supports you in troubleshooting and optimizing the user program,
especially for motion control or closed-loop control applications. Trace only supports
saves measurements on a SIMATIC memory card. You will find additional information
on "Trace" in the Using the trace and logic analyzer function
(http://support.automation.siemens.com/WW/view/en/64897128) function manual.

Product overview
2.3 Properties
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 17
•Integrated system diagnostics:
–The alarms for the system diagnostics are automatically created by the system and
displayed on a PG/PC, HMI device or the Web server. System diagnostics information is
also available when the CPU is in STOP mode.
•Integrated security:
–Know-how protection
The assignment of passwords protects user blocks against unauthorized access and
modifications.
–Copy protection
Copy protection links user blocks to the serial number of the SIMATIC memory card or
to the serial number of the CPU. User programs cannot run without the corresponding
SIMATIC memory card or CPU.
–Access protection
Extended access protection provides high-quality protection against unauthorized
configuration changes. You can use authorization levels to assign separate rights to
different user groups.
–Integrity protection
The system protects the data transferred to the CPU against manipulation. The CPU
detects erroneous or manipulated engineering data.
You can find additional information on the topic of "Protection" in the system manual
ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
•Support for ET 200AL
–Simple connection of IP 65/67 I/O modules to the CPU.
•Communication CPs
–CP 1542SP-1: Flexible expansion of the ET 200SP system with an additional Ethernet
interface; network separation.
–CP 1542SP-1 IRC: Seamless data recording with time stamping, support for
standardized telecontrol protocols DNP3 and IEC.
–CP 1543SP-1 ISEC: With the integrated security functions firewall (Stateful Inspection)
and VPN protocol (IPSec), the communications processor protects ET200SP stations
and subordinate networks against unauthorized access, and employs encryption to
protect data transmission against manipulation and espionage.

Product overview
2.3 Properties
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
18 Equipment Manual, 05/2021, A5E03506268-AD
•Address space
–A larger address space of 2560 bytes (2048 bytes for ET 200SP module + 512 bytes for
ET 200AL modules) is available within the station.
•CPU 1510SP-1 PN supports the following additional functions:
–PROFIenergy
You can find information on the topic of "PROFIenergy" in the PROFINET function
manual (https://support.industry.siemens.com/cs/ww/en/view/49948856) and in the
PROFINET specification on the Internet (http://www.profibus.com).
–Shared device
You can find information on the topic of "Shared device" in the PROFINET function
manual (https://support.industry.siemens.com/cs/ww/en/view/49948856).
–Configuration control
You can find information on the topic of "Configuration control" in the system manual
ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
–Isochronous mode
You can find information about the "Isochronous mode" topic in the PROFINET
(https://support.industry.siemens.com/cs/ww/en/view/49948856) function manual.

Product overview
2.4 Operating and display elements
CPU 1510SP-1 PN (6ES7510-1DJ01-0AB0)
Equipment Manual, 05/2021, A5E03506268-AD 19
2.4 Operating and display elements
2.4.1 Front view of the module with BusAdapter
The figure on the left shows the CPU 1510SP-1 PN including a plugged BA 2xRJ45
BusAdapter. The figure on the right shows a separate view of the BA 2xRJ45 BusAdapter.
①
Mounting rail release
②
Labeling strips
③
LEDs for status and error displays
④
LED for display of the supply voltage
⑤
Mode switch
⑥
Slot for the SIMATIC memory card
⑦
Connection for supply voltage (included in product package)
⑧
Cable support and attachment for port P3 of the PROFINET interface
⑨
LEDs for status displays of the PROFINET interface: LK1 and LK2 on BusAdapter, LK3 on CPU
⑩
Port P3 of the PROFINET interface: RJ45 socket
⑪
Separate view of the BusAdapter
⑫Port P1 R of the PROFINET interface: RJ45 socket on BusAdapter BA 2×RJ45
R: Ring port for configuring a ring topology with media redundancy
⑬Port P2 R of the PROFINET interface: RJ45 socket on BusAdapter BA 2×RJ45
R: Ring port for configuring a ring topology with media redundancy
Figure 2-2 Front view of the CPU 1510SP-1 PN with BusAdapter