EUCHIPS EUP10D-1HMC-0-120 User manual

EUP10D-1HMC-0-120(Product No.: 3.04.001575)
DALI Constant Current Dimming Driver
Summary
Product Feature
Touch DIM(Push DIM)
200VAC-240VAC
50/60Hz
82%@230VAC, Full load
0.95@230VAC, Full load
<0.5W
cold start,10A(twidth=10us measured at 50% Ipeak@230VACC
0.06Amax@230VAC, Full load
110*30*22.5mm(L*W*H)
60g
IP20
-20℃~50℃
-40℃~85℃, 20-90%RH
75℃
L-N:500V
I/P-O/P: 1500VAC
PC
50,000h@tc:75℃
1%-100%
50VDC
±5%
<3%
DALI /
>100,000 times
1
120mA/9-45VDC/5.4W
220mA/9-45VDC/9.9W
150mA/9-45VDC/6.75W
250mA/9-40VDC/10W
170mA/9-45VDC/9.9W
270mA/9-37VDC/9.99W
200mA/9-45VDC/9W
300mA/9-33VDC/9.9W
<10%@230VAC, Full load
EUP10D-1HMC-0-120
Surge
Withstand Voltage
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI Standrad
tc
Lifetime
Material
Dimming Range
Dimension
515*235*140mm(L*W*H), 9.5Kg/Carton/100PCS
Packing Size
G.W
IP Rating
Working Temp.
Storage Temp.; Humidity
Dimming Mode
Switch Cycle
5 yearsWarranty Condition
No Load Output Voltage
Turn On Delay Time <1s, at 230Vac
Efficiency
Standby Power
Current
Inrush Current
THD
Current/voltage/power
Ripple Current
Channel
Current Tolerance
Voltage
Frequency
Power Factor
No Load
Short Circuit
Over Load
The LED Driver will not be damaged.
Hiccup mode, recovers automatically after fault condition is removed
No Output, recovers automatically after fault condition is removed
Safety
Others
Function
Model
Output
Input
Protection
Technical Parameters
1/2
User’s manual: 2019-8 www.euchips.com
Current Selection Table
Remark: Function default setting is: 120mA (@switch are all OFF state)
120mA 150mA 170mA
9-45V 9-45V
220mA
9-45V9-45V
ON OFF 220mA
9-45V
250mA
9-40V
270mA
9-37V
300mA
9-33V
EUP10D-1HMC-0-120 is a 10W AC/DC constant current mode output LED driver featuring the multiple levels
selectable by DIP switch and complies with DALI standard protocol IEC 62386. EUP10D-1HMC-0-120 can be
connected to DALI main controller or Touch DIM(Push DIM) to achieve a smooth dimming effect.
·Single channel output, output current level selectable by DIP S.W.
·Meet DALI Protocol IEC 62386-207
·Support Touch DIM (Push DIM)function
·High efficiency up to 82%
·Built-in active PFC function
·Dimming effect smooth, no flicker
·Protections: Short circuit, over load, no load
·Suitable for indoor LED lighting application, such as down light, spot light, and so on

Dimension(mm) Wiring Diagram
22.6
110.0
29.6
EUP10D-1HMC-0-120
L
N
DA1
DA2
OUTPUT
LED -
LED+
220-240VAC
Input
DALI Master
Lamp
DALI Constant Current Dimming Driver
2/2
User’s manual: 2019-8 www.euchips.com
Push DIM(Touch DIM) Diagram
Push DIM Function
1. Press the Touch DIM switch for 8s or more,the driver can be controlled via Touch DIM switch.
2. Short press the Touch DIM switch (<0.5s) to control the lamp on or off.
3. Long press the Touch DIM switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Touch DIM switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long
pressing Touch DIM switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
DALI Wiring Diagram
Remarks: use only open push switch (without indicator light). When using synchronous connection, the line length between each device and equipment shall not exceed 20 meters.
DALI Driver 1
DA
DA LED-
LED+
L
N
DALI Driver 2
DA
DA LED-
LED+
L
N
L
N
DALI Controller
DALI Driver 1
DA
DA LED-
LED+
L
N
DALI Driver 2
DA
DA LED-
LED+
L
N
Push DIM Pannel(Touch DIM)
LN
※The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions, the function of the product shall prevail.Please contact us if you have any
questions .
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75- 1.5mm²is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
Derating CurveDimming Curve PF VS Load
Eff. VS LoadTHD VS load
Ambient Temperature(℃)
Load (%)
0
20
40
60
80
100
-20 -10 10 20 30 40 50 600
Output (%)
Input signal(%)
0
0
4
14
2 1 29
36 43
50 5 7
64
7 1 78
85
92
100
20
40
60
80
100
Load (%)
THD(%)
THD
060 70 80 90 100
2
4
6
8
10
12
Load (%)
PF
0.97
0.965
0.96
0.955
0.95
0.945
60 70 80 90 100
230Vac
Load (%)
Efficiency(%)
70.00
75.00
80.00
85.00
90.00
95.00
60 70 80 90 100

EUP10D-1HMC-0-120(产品代码: 102100201)
DALI恒流调光驱动器
概述
产品特点
Touch DIM(Push DIM)
200VAC-240VAC
50/60Hz
82%@230VAC, 满载
0.95@230VAC, 满载
<0.5W
冷启动,10A(在50%Ipeak下测twidth=10us)@230VACC
0.06Amax@230VAC, 满载
110*30*22.5mm（长*宽*高）
90克
IP20
-20℃~50℃
-40℃~85℃, 20-90%RH
75℃
L-N:500V
I/P-O/P: 1500VAC
PC
50,000小时@tc:75℃
1%-100%
50VDC
±5%
<3%
DALI /
>100,000次
1
<10%@230VAC, 满载
EUP10D-1HMC-0-120
浪涌
耐压标准
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI 标准
tc
寿命
材质
调光范围
尺寸
515*235*140mm(长*宽*高), 9.5Kg/箱/100PCS
包装尺寸
毛重
防水等级
工作温度
储存温度、湿度
调光方式
开关周期
5年质保
空载输出电压
启动延时 <1s, at230Vac
效率
待机功耗
电流
浪涌电流
THD
电流/电压/功率
波纹电流
通道
电流公差
电压
频率
功率因素
空载
短路
过载
驱动不会损坏
打嗝，移除故障后自恢复
无输出，移除故障后自恢复
安全
其它
功能
型号
输出
输入
保护
技术参数
1/2
用户手册: 2019-8 www.euchips.com
电流选择表
备注：出厂默认设置电流为120mA(1,2,3在OFF状态)
EUP10D-1HMC-0-120是一款可以提供120/150/170/200/220/250/270/300mA 8档电流的LED
驱动器。输出电流可以过DIP拨码开关简易设置, 符合DALI标准协议IEC62386. 用DALI主控/
Touch DIM(PushDIM)开关调光，曲线平滑、无闪烁。
·单通道输出，输出电流可通过DIP拨码开关选择
·遵循DALI协议标准 IEC62386-207
·支持Touch DIM(Push DIM)功能
·效率高达 82%
·内建主动式PFC功能
·调光效果平滑，无闪烁
·保护：短路保护，过载保护，空载保护
·适用于LED室内灯具,比如筒灯，射灯等
120mA/9-45VDC/5.4W
220mA/9-45VDC/9.9W
150mA/9-45VDC/6.75W
250mA/9-40VDC/10W
170mA/9-45VDC/9.9W
270mA/9-37VDC/9.99W
200mA/9-45VDC/9W
300mA/9-33VDC/9.9W
120mA 150mA 170mA
9-45V 9-45V
220mA
9-45V9-45V
ON OFF 220mA
9-45V
250mA
9-40V
270mA
9-37V
300mA
9-33V

产品尺寸 应用接线图
22.6
110.0
29.6
EUP10D-1HMC-0-350
L
N
DA1
DA2
OUTPUT
LED -
LED+
220-240VAC
输入
DALI 主控
灯具
DALI恒流调光驱动器
2/2
用户手册: 2019-8 www.euchips.com
Push DIM(Touch DIM) 接线图
Push DIM 功能
1.长按8s进入Touch DIM模式。
2.短按Touch DIM 开关 (<0.5秒) 进行灯的亮暗控制。
3.长按Touch DIM 开关 (>0.5秒) 进行灯具的亮度调节，光是调亮还是调暗，随着每次按压的开关变化而变换。
4.双击Touch DIM 开关 (<0.3秒) ，连接的所有灯具将达到最亮状态。
5.亮度调节范围为1%-100%。
6.具有断电记忆功能，重新上电将恢复到上一次断电的状态。
DALI应用接线图
备注: 只能使用开路的按压式开关(不带指示灯)。采用同步连线时每个设备和设备之间的线长不超过20米。
DALI 驱动 1
DA
DA LED-
LED+
L
N
DALI 驱动 2
DA
DA LED-
LED+
L
N
L
N
DALI控制器
DALI 驱动 1
DA
DA LED-
LED+
L
N
DALI 驱动 2
DA
DA LED-
LED+
L
N
Push DIM 面板(Touch DIM)
LN
※ 本说明书内容如有更新，恕不另行通知。若您使用的产品功能与说明书不一致时，请以产品为准。如有疑问请与我们联系。
注意事项:
1、本产品请由具有专业资格的人员进行调试安装。
2、本产品不能防水，需避免日晒雨淋，如安装在户外，请用防水箱。
3、良好的散热条件会延长产品的使用寿命，请把产品安装在通风良好的环境。
4、请检查使用的LED电源输出电压电流，是否符合产品要求。
5、出于安全考虑，推荐输入和输出（信号端除外）用0.75-1.5mm² PVC或橡胶线缆，并确保接线牢固，以免电线过热或接触不良触发事故。扁平电源线不适用。
6、通电调试前，应确保所有接线正确，以避免因接线错误而导致灯具损坏。
7、如果发生故障，请勿私自维修；如果有疑问，请联系供应商。
调光曲线 降额曲线
THD VS 负载
PF VS 负载
效率 VS 负载
环境温度（℃）
负载 (%)
0
20
40
60
80
100
-20 -10 10 20 30 40 50 600
输出 (%)
输入信号(%)
0
0
4
14
2 1 29
36 43
50 5 7
64
7 1 78
85
92
100
20
40
60
80
100
负载(%)
THD(%)
THD
060 70 80 90 100
2
4
6
8
10
12
230Vac
0.97
0.965
0.96
0.955
0.95
0.945
60 70 80 90 100
负载(%)
PF
230Vac
70.00
75.00
80.00
85.00
90.00
95.00
60 70 80 90 100
负载(%)
效率(%)