Eurekazone EZ SMART User manual

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (877 681-7955 [e-mail] www.eurekazone.com
DUST PORT
v14-01
The EZ Smart Dust Port can easily be shaped and attached to the front of the blade housing on
most circular saws on the market to better extract saw dust with your vacuum.
Installing The Dust Port
Step . Set the saw on a solid work surface and
unplug the saw's electrical supply before beginning
the installation process. See fig.
Step 2. Remove the blade from the saw as show in
fig. 2
Step 3. Using a hot air gun or blow dryer, heat the
pre shaped dust port until the wings become
pliable. This will aid in shaping the dust port to your
saw. Use caution as the plastic begins to heat to
avoid injury or burns. See Fig. 3
Step 4. While the plastic is still pliable, place it over
your saw's housing in the desired position and form
it to the shape of the housing. Hold this shape for a
few moments while the plastic cools to retain the
shape. Note: Make sure the placement of the dust
port does not interfere with the saws beveling or
tilt. See Fig. 4- & Fig. 4-2
Fig.
Fig. 2
Fig. 3
Fig. 4-
Fig. 4-2
Parts Included
- Dust Port
2 - 8-32 Washers
2 - 8-32 machine screws
- Aluminum Dust Port Hose Adapter
Notice: Prior to installing your EZ Smart Dust Port, please
ensure that you have read and fully understand these
instructions and those provided for any power tools that you
may use during this installation. Disconnect your saw from
the power supply while completing this installation. When
required, use hearing and eye protection.

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (877 681-7955 [e-mail] www.eurekazone.com
DUST PORT
v14-01
Installing The Dust Port Continued
Step 5. Locate and mark the center of your saw's
housing where the dust port opening will be drilled.
See Fig. 5
Step 6. Using a ¼ drill bit, drill a starter hole in the
location of your mark from Step 5. See Fig. 6
Step 7. Using a 3/ 6 – 7/8” Step bit (Shown in Fig.7- )
to increase the starter hole to the full 7/8”. as shown in
Fig. 7-2
Step 8. Take a mill file and clean up the hole so no burrs
remain as shown in Fig. 8- & Fig. 8-2. Make sure to also
de burr the inside of the opening.
Step 9. Before installing the dust port you will need to
remove the front handle of your saw (If Applicable) in
order to have access to drill and tap the mounting holes
on the motor side of the housing. As Shown below in
Fig. 9- & Fig. 9-2.
Fig. 5
Fig. 6
Fig. 7-1
Fig. 7-2
Fig. 8-2
Fig 8-
Fig 9- Fig. 9-2

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (877 681-7955 [e-mail] www.eurekazone.com
DUST PORT
v14-01
Installing The Dust Port Continued
Step 0. Center mount the dust port over the hole
ensuring that it covers the opening entirely. Then
using a 5/32” drill bit, drill a mounting hole through
the dust port and outside wall of the housing as
shown in Fig. 0.
Step . Use an 8-32 tap to thread the mounting
hole as shown in Fig. .
Step 2. Place one of the provided washers over
the mounting screw and secure the dust port to the
housing as shown in Fig. 2- & Fig. 2-2
Step 3. Repeat steps 0 through 2 to secure the
opposite side of the dust port to the housing.
Step 4. The installation of the dust port is now
complete. Finish up by re installing the Saw's
handle which was removed in Step 9 as shown in
Fig. 3.
Note: Some dust collection hoses may require the
the use of the aluminum Dust Port hose adapter.
The adapter slides into the dust port as shown in
Fig. 4- & Fig. 4-2. Once inserted, your - /4”
vacuum hose should slide over the adapter
connecting the vacuum to the saw.
Fig. 0
Fig.
Fig. 12-1
Fig. 2-2
Fig. 3
Fig. 4- Fig. 4-2