Jegs 81503 User manual

Installation Guide for 81503
Sandblast Cabinet Dust Collection System
Universal Fitment

Parts List
1Vacuum Motor [120 VAC, 60Hz, 12 Amp]
2
Filter
Collector [1.75 gal.]
3
4
Shaker Knob Assembly
Collector Trap Door
7
5
6
Vacuum to Collector Latch
Power Cord
1
1
2
3
45
6
7

2
Read Before Installation Warning
Thank you for your purchase of this JEGS Sandblast
Cabinet Dust Collection System.
Before installation, please be sure to verify that all of
the kit components have been received. Reference the
parts list on the previous page. If any components are
missing or damaged please contact customer service
at: 1.800.345.4545.
Installation of this dust collection system can be
completed with basic hand tools. If you are not
comfortable with this process please contact a trusted
service shop to perform the installation.
If you are having issues, or have questions
regarding the installation of this dust collection
system, please contact our technical support
department at: 1.800.345.4545.
Return Information: Before modifying any of the parts
in this system, please trial fit. Once this kit has been
modified it will not be accepted for return.
• Use caution when sandblasting parts that are
exposed to flammable materials. Do not al-
low fumes to enter the vacuum motor; this is an
explosion hazard.
• Wear a respirator when cleaning or emptying the dust
collection system. Avoid breathing the dust produced.
• Wear ear protection. This unit produces a high level
of noise.
• Do not operate the dust collection system if the inlet
is blocked.
• Do not operate in wet conditions.
• This unit is equipped with a 56 in. cord. If an ex-
tension cord must be used, do not exceed
50 ft. total length. An 18 AWG gauge wire or larger
extension cord is necessary.
• Uplug the dust collector when cleaning, changing
filter, or servicing.

3
Assembly
Shaker Knob
Installation
1. Disconnect the retainer clips and lift the upper portion,
containing the vacuum motor and filter, away from
the lower collector.
2. Disassemble the shaker knob by unscrewing the inner
strike plate and nut.
3. Slide the threaded end through the hole on the side
of the collector. Keep the spring on the outside of
collector.
4. Reattach the nut and inner striker plate inside the
collector. Tighten the nut against the striker plate to
ensure a secure attachment.
Mounting
Installation
1. Align the collector hose outlet to vacuum port
at rear of sandblaster cabinet. To ensure prop-
er fitment, check the sandblast cabinet’s vacuum
outlet diameter. This unit features a 2
1
/
8
in.
diameter outlet. Some units may require an adapter
to fit.
2. When positioning this dust collect unit, check for
clearance between the collector hose outlet and the
sandblast cabinet’s vacuum port shield. Minimal, or
no clearance will restrict flow and can lead to vacuum
motor damage.
3. With the unit in position, mark the dust collector’s
mounting bracket holes on the back of the sandblast
cabinet. With the holes marked, set the dust collector
aside and drill the holes.
4. Align the dust collector unit mounting brackets with
the drilled holes and bolt into place.
• Note: Mounting hardware is not included with
this kit.
Use
Dust Collector System
1. To use this system, after installation, connect to a
120V power source.
2. When using the sand blasting cabinet this unit will
remove dust allowing for better visibility.
• Note: This dust collection system does not feature
an On/Off switch. It turns once when plugged into
a wall outlet. Some sandblast cabinets feature an
outlet that can be used to power this unit.
Shaker Knob
• Push the shaker into the collector. Doing this will
cause the shaker to hit the filter and break loose im-
pacted debris. The spring will retract it to the original
position.
Maintenance
Filter Remove & Replacement
1. Unplug the vacuum.
2. Disconnect the two clasps connecting the vacuum
motor to the collector.
3. Lift the upper assembly away, making sure to take into
account the length of the filter to clear the collector.
4. Remove the wing nut to remove the filter.
5. Reverse steps to reinstall.
Emptying the Collector
1. Position a bucket, or trash can, underneath the dust
collector.
1. Disconnect the clasp at the bottom of the collector.
2. Open the trapdoor
3. Hit the shaker knob to break debris loose.
Use & Maintenance