EUROLAIKAS BC Series User manual
BC Series DC Brushless
Barrier Gate
Instruction Manual
Warning:
Please read this instruction manual carefully before installation, in which involves with
some important information about installation, usage, maintenance and safety.
Any undefined operation under this instruction is not allowed. Improper usage of the
barrier gate will result in damage to the product and cause serious injury or property
losses.
Please keep this instruction manual properly for future reference.
The design and manufacture of the barrier gate is totally complied with the current
regulations.
Considering the possibility of danger, the installation must strictly comply with the
construction standards and electrical operation procedures as following
Before installation, please check if additional equipment or materials are needed in
order to meet specific requirements.
The handling of packing materials must comply with local regulations.
Please do not modify any parts, except for those defined under this instruction manual.
Any undefined modification may cause troubles. Any damages to the product arising
therefrom shall be beyond the liability of the company.
Please do not leak water or any liquid into the controller or any other open devices.
Please disconnect the power immediately if any mentioned cases happened.
Please keep this product away from heat and open fire. Or it may damage the
components; cause the failure or other hazards.
Nobody is allowed to stand or walk under the barrier boom, especially when it’s on
moving. Please do not stand or leave any objects within the boom rotation range of
90
°
due to the collision by cars.
Spring adjustment, operation mode setting, induction devices installation must be
operated by qualified professionals.
Table of Contents:
1. Product Outline..4
2. Functions and Features4
3. Technical Parameter List..5
4. Machine Core Components.6
5. Installation Direction Definition6
6. Assembly and Installation7
6.1. Pre-Installation Check..7
6.2. Basic Structure Installation.....7
6.3. Boom Balance Adjustment..8
6.4. Power Wiring.9
6.5. Electrify Check.......10
6.6. Adjust the Place of Barrier Boom.10
6.7. Manually Open/Close.11
6.8. Spring Configuration..12
7. Control Board Wiring..12
7.1 Wiring Instruction13
7.2 Parameter Adjustment14
8. Technical Support15
9. Packing List..16
10. Terms of Service..16
1. Product Outline
On the basis of absorbing essence of similar products at home and abroad, the company has
researched and developed this BC series DC brushless barrier gate. This product adopts international
advanced technology, with mechanical and electrical integrated design, which fully realizes automation
and intelligence of operating, brings convenience、safety and speed for using.
. Functions and Features
1. Efficient DC brushless motor and precise gear reducer drive with mechanical and electrical control
integrated. More flexible and convenient operation, safe and reliable for using, completely maintenance
free during its service time.
2. Adopts precise four-bar linkage mechanism and spring balance device which enable the barrier boom
work with soft start-slow stop function in fast and stable without any impact. Reduces the driving power in
maximum, extends its service life.
3. Integrated machine core, small size with large power, wall-mounted installation, easy for assembling
and disassembling.
4. DC 24V low voltage brushless motor, adapts to global voltage (110~220±15%). It highlights for safer
use, less noise, low heat output, frequently use, energy conservation and environmental protection.
5. The combination of motor hall encoder and control unit ensures the control to mechanism moving
position at the utmost.
6. The dedicated controller system has high integration and strong logic performance. It can be
connected with any toll system of roads and bridges、parking lots and so on.
7. Intelligent speed adjustment efficiently reduces the trembling of the barrier boom, suitable for different
occasions.
8. High-sensitivity Auto-reverse function will prevent incorrect operation and other crash or hitting
accidents.
9. Open first anti-smash function barrier boom will perform opening action once received an opening
signal during the closing process.
10. Humanized anti-collision boom dropping-out mechanism, when the vehicle accidently hits the barrier
boom, the anti-collision mechanism will rotate the boom to avoid damage to the vehicle and the barrier
gate.
11. High-strength precision cast steel machine case, with outdoor metal powder electrostatic spraying
surface treatment, waterproof and dustproof, protection class up to IP54.
3. Technical Parameter List
Barrier Gate BC3015 BC4020 BC5035 BC6050
Boom Length
Round boom
φ75, ≤3m;
Octagonal boom
80×46, ≤3m
Round boom
φ75, ≤4m;
Octagonal boom
80×46, ≤4m
Octagonal
boom 100×45,
≤5m
Octagonal
boom
100×45, ≤6m
Open/Close Time 1.5 sec 2.0 sec 3.5 sec 5.0 sec
Transmission Ratio
1 60 1 120
Max. Power 140w
Power Supply AC110-240V
±15%
Machine Case 1.5mm Steel Plate
Machine Case Size
（W×D×H） 332 × 325 × 962mm
Net Weight 42kg
Operating Temperature
Range
-40~+60 ℃ (temperature under -20℃ should be equipped with
electric heating plate)
Driving Method Brushless DC motor + Helical gear reducer
Protection System(IP) 54
Insulation Class F
Relative Humidity ≤85%
Motor Unload Speed 1500r/min
Service Life 5 million times
Remote Control Distance ≤30m (empty environment, sunny weather)
Running Noise ＜50dB
Surface Treatment Outdoor metal powder electrostatic spraying
4. Machine Core Components
1
2
3
4
5 6 7 8 9
1010
1111
1
2
3
4
5
6
7
8
9
1010
MotorMotor
LinkLink rodrod
CrankCrank armarm
RockerRocker springspring armarm
SpringSpring
SpringSpring rod(upper)rod(upper)
ReductionReduction gearboxgearbox
OutputOutput shaftshaft
BoomBoom traytray headhead
BoomBoom
Machine Core Drawing
5. Installation Direction Definition
Leftward Fixed Rightward Fixed
6. Assembly and Installation
6.1 Pre-Installation Check
Note:
Barrier gate installation must be carried out by qualified technician; Installation must comply with relevant
regulations. Before installation, please read this instruction manual carefully.
Meanwhile, please definite the installation direction of barrier gate boom to be leftward or rightward fixed.
Please make sure that the boom will operate freely without any impediment.
Please make sure the mounting base is strong enough and the size is suitable.
Please make the installation spots for all the relative equipments are suitable to avoid any collision.
6. Basic Structure Installation
Please check the accessories according to the packing list (Packing list shown in this instruction)
Please determine the place of anchor bolt holes and control cable according to the installation of barrier
gate, drill 4 holes for expansion bolt M12 or embed 4pcs of M12 anchor bolts based on the press board.
Separately wire the power cable and control line with conductors and bury them to its corresponding
place, leave enough cable on the ground.
Put the barrier gate in the right place (Keep the boom dropping-out and vehicle passing on the same
direction), make sure the barrier gate is vertical to the ground, align the press board to the anchor bolts,
lock and fasten them.
Put the boom into boom tray, add plastic gasket on both sides, use the spanner to clamp the boom by
screws nuts.
6.3 Boom Balance Adjustment
The tension of the spring is relative to the boom length, the spring has been assembled in the factory
according to the different boom length, also the relative adjustments on boom operating speed、
operating balance during opening/closing process has been set up before delivery. Spring tense must be
re-adjusted by professionals if there were any changes on the boom length or weight. Please check and
adjust according to the following steps.
1. Open the barrier gate side door and remove the upper cover.
2. Unplug the power cord.
3. Toggle the crank from the side door to unlock it, manually adjust the boom to the place of 45 degrees
then release the hand. If the boom keeps stable on the place of 45 degrees’ angle, indicating that it is
with the best spring force.
4. If the spring force is too large or too small, then should be adjusted. First, loosen the double nuts on
the top of the spring, rotating the double nuts to increase or decrease the tension of the spring, then
adjust the barrier boom again to its 45 degrees’ angle position to check the spring tension.
5. Through repeating the above forth step to adjust the boom to its best balance, then fasten the double
nuts, adjustment is complete.
NutNut
ScrewScrew
PressPress downdown toto unlockunlock
6.4 Power Wiring
The power module of the barrier gate has been connected to the control board before delivery. To ensure
operational safety and avoid damage to the components, please disconnect the circuit breaker first, and
then connect the L and N of AC power into the input port of circuit breaker.
AC110-220AC110-220
InputInput
ONON
OFFOFF
I
O
LNCOMCOM +V+V +V+V +V+V
COMCOMCOMCOM
ConnectConnect toto controllercontroller
GNDGND +24V+24V
Note: Only professional technicians can engage in the installation and after sales maintenance
for this product and are responsible for any damage caused by improper operation.
6.5 Electrify Check
Please close the circuit breaker to connect the power after correctly wired. The indicator light on the
control board will be on once the power is connected; After powering on, please press the open/close
button on the remote control, barrier gate will automatically detect the opening/closing limit switch (both
limit switches are required to be detected). After detecting the opening/closing limit switch, the
auto-detecting data will be saved automatically with a long sound of the buzzer, after which, the barrier
gate will work normally.
6.6 Vertical adjustment of barrier boom
If the barrier gate boom cannot open to its vertical position or close to its horizontal position. Please take
the following steps to adjust it
1. Open the barrier gate door, unplug the power cord.
2. Open and remove the upper cover.
3. Loosen the two fasten screws on rocker spring arm when the barrier boom is in erect. Adjust the
boom to its horizontal position manually. Use the torque wrench to tighten the two fastening
screws (locking force is 72 N·m)
4. Connect the power to work, check whether the boom opens/closes in place. If not, please
re-adjust it after power off until the performance achieving the ideal state.
ScrewScrew
6.7 Manually Open/Close
The barrier gate may stay in the vertical or horizontal mechanical self-locking position when power off, if
to manually open/close the boom at this time, please follow the steps as below
1. Open the barrier gate door.
2. Unplug the power cord
3. To close when boom in vertical position Use a specific tool to lever the crank away from its
self-locking position, manually press down the barrier boom to its horizontal position to finalize
the closing action.
4. To open when boom in horizontal position Use a specific tool to lever the crank away from its
self-locking position, barrier boom can be manually lifted by this time.
Note Please stabilize the boom when manually open it, in order to avoid any unnecessary damage
caused by the spring tension.
Downward
lever the crank
to unlock
Downward
lever the crank
to unlock
Crank
Crank
6.8 Spring Configuration
Boom Length Spring
3M Octagonal Boom 80x46 mm φ3.5x2pcs
4M Octagonal Boom 80x46 mm φ3.5x1pc; φ4x1pc
5M Octagonal Boom 100x45 mm φ4 x1pc; φ4.5 x1pc
6M Octagonal Boom 100x45 mm φ5x2pcs
7. Control Board Wiring
U
W
GND
V
Ha
Hb
Hc
VCC
GND
24V
Screen
Completely Open
GND
24V
12V
Open
Close
Stop
GND
IR
Vehicles Detector
12V
/
-
/
+
C
B-
A+
5
V
G
N
D
D
A
T
A
5
V
G
N
D
o
n
f
i
r
m
CL OP
M
e
n
u
E
x
t
e
r
n
a
l
Completely Close
A
n
t
e
n
n
a
Warning!
The controller for DC brushless barrier gate is specially designed for the use of low speed and medium
speed barrier gates. The place of the running barrier boom is continuously detected by the motor hall,
which replaces the limit switches used in conventional barrier control systems.
The combination of the hall encoder and the controller unit ensures the maximum control to the boom
optimum running place.
Note!
If some special functions are required, the controller's connection may differ from which shown in this
wiring illustration.
Important Note:
All input signals (like push buttons, limit switches, etc.) must be connected in the volt-free contact way.
7.1 Wiring Instruction
Motor Port Insert an 8 ends motor cable port;
Power Port Insert a 2 ends power cable port;
Close in Place When the barrier boom is closed in place, the 2 ports will be NC;
Open in Place When the barrier boom is opened in place, the 2 ports will be NC;
12V+ Output +12V;
GND Ground;
12V+ Output +12V;
OPEN OPEN signal input port (another end connects with +12V port);
CLOSE CLOSE signal input port (another end connects to +12V port);
STOP Halfway stop during opening or closing signal input port (another end connects to +12V port);
Loop Detector Loop detector signal input port (NC, automatically close after powering off);
Open in Place Signal NC Open in place output normal close signal NC;
Close in Place Signal NC Close in place output normal close signal NC;
Specific Function Description:
1. Travel learning after powering on, press the “close” button on the remote control, after barrier boom
closed in place, the buzzer will ring a long beep; then press “open” button on the remote control, after
opened in place, the buzzer will ring a long beep again, after which the travel learning is complete. The
barrier gate will operate in proper condition.
2. Open/Close function connect +12V and open input ports to send open signal; connect +12V and
close input ports to send close signal; connect +12V and stop input ports to send stop signal.
3. Loop detector function connect signal line to the 2 loop detector line ports, after loop detector coil
detecting the passing of vehicles, the barrier gate will automatically close.
4. Remote control learning Long press the “menu” button to enter into L mode, press “+” or “-” button to
select L-F option, press “menu” button to enter into L-F, then press any buttons on the remote control,
after the buzzer rings a long beep, learning is complete. If more remote controls are required to be
added, please press “menu” button again after the first remote control is paired, press any buttons on the
remote control and after the buzzer rings, learning will be complete.
7. Parameter Adjustment
Long press “menu” button on the control board to enter into L mode, press “+” or “-” button to select
corresponding Alphabet menu or Number menu, press “menu” to enter into, to adjust the parameters
through “+” or “-” buttons, press “menu” again to back to previous menu, after all parameters are set
please press “confirm” to finish the adjustment.
Parameter adjustment—3m boom
Function Alphabet menu Number menu Parameter setting
Opening speed L-1 L01 80
Closing speed L-2 L02 75
Opening deceleration travel L-L L10 45
Closing deceleration travel L-B L11 45
Automatic closing L20
Parameter adjustment—4m boom
Function Alphabet menu Number menu Parameter setting
Opening speed L-1 L01 65
Closing speed L-2 L02 60
Opening deceleration travel L-L L10 45
Closing deceleration travel L-B L11 45
Automatic closing L20
Parameter adjustment—5m boom
Function Alphabet menu Number menu Parameter setting
Opening speed L-1 L01 45
Closing speed L-2 L02 40
Opening deceleration travel L-L L10 45
Closing deceleration travel L-B L11 45
Automatic closing L20
Parameter adjustment—6m boom
Function Alphabet menu Number menu Parameter setting
Opening speed L-1 L01 35
Closing speed L-2 L02 30
Opening deceleration travel L-L L10 45
Closing deceleration travel L-B L11 45
Automatic closing L20
8. Technical Support
If there is any operation failure that can’t be handled by your technical staff, please contact our
authorized service representative or professional assistance.
Please provide the barrier gate model, product serial number, controller version and other information
when contact us for technical support services, which you can find in the barrier gate machine case
model plate.
9. Packing List
10. Terms of Service
1. Two-year free maintenance for the system(barrier gate boom、remote control is not covered by this
warranty)
2. Lifetime repair guarantee.
3. Technical support.
* The following situations are not covered by free maintenance (or replacement)
1. Damages to this product caused by installation which is not complied with the instructions under this
manual.
2. Unstable power supply, the using power supply exceeds the system specified voltage range, and
doesn’t meet the national safety power standard, therefore causing the damages to the product.
3. Damage to the system appearance due to improper installation or usage.
4. Damage to the product due to force majeure such as natural disasters.
5. Beyond the warranty period.
6. Service items not promised by manufacturer.
The manufacturer reserves the right to modify the technical specifications of the product to meet
the latest technological developments with prior notice.
This instruction and service terms involved are to the final interpretation of the product
manufacturer.
Number Title Qty Unit Note
1 Barrier gate machine 1 Unit
2 Machine case press board
2 Piece
3 Expansion bolt M12 4 Set
4 Remote control 2 Unit
5 Case Key 2 Unit
6 Instruction 1 Piece
Included in machine
package
7 Barrier gate boom 1 unit Optional, separate
package
8 Boom holder 1 unit Optional
9 Expansion bolt M8 4 Set Optional, for fixing boom
holder
10 Plug-in Machine control 1 unit Optional
Table of contents
