EVENING LIGHT PAN5x5x30 User manual

1
PANEL
PAN5x5x30 PAN4x4x30
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au V1.3

2
CONTENTS
Safety Instructions
- Power Input & Power Linking
Product Installation
- Fuse replacement
Product appearance
- Lux Chart
- Dimensions
Control Board Operation
- DMX Addressing
- DMX Modes
- Dimmer Speed Setting
- Sound Mode
- Setting Static Colors
- User Mode
- Automatic Mode
DMX Values
Technical Specifications
Warranty

3
Safety Instructions
WARNING
•Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
•Do not look at the light source when the device is on.
•CAUTION: This unit's housing may be hot during and after operation.
•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
•Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•ONLY connect this device to a grounded and protected circuit.
•ONLY use the hanging bracket to carry this device.
•In case of a serious operating problem, stop using immediately.
•The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.

4
PRODUCT APPEARANCE, LUX CHART, DIMENSIONS
1 2 3 4
56 7 8
910 11 12
13 14 15 16

5
CONTROL BOARD OPERATION
Press the Menu until one of the following displayed:
Display
Function
1.DMX Address
To set DMX
address
2.DMX Channel
To set DMX channel modes:
5x5 Model CH 03, CH 05, CH 09,CH 75, CH80
4x4 Model CH 03, CH 05, CH 09, CH 48, CH53
3.Dimmer Curve
To set dimmer speeds: 01, 02, 03, 04
4.Sound Mode
To set sound active mode and the sensitivity (Speed 000 ~ Speed 100)
5.Static Color
To set static colors: Static Color R, G, B, GB, RG, RB, RGB
6.Manual Color
To set user mode intensity of R, G, B separately for color mixing and strobe rate
7.Auto Program
To set built-in automatic programs: Pr 01 ~ Pr 10 and speeds 000 ~100
8.Master/Slave
To set Master/Slave modes
Use Up and Down button to select your desired operation, then press Enter to confirm.
DMX Addressing:
After select the "DMX Address" and press Enter, then use Up and Down to set the desired DMX address
(001~512), press "Enter" again to confirm.
DMX Modes
After select the "DMX Channel" and press Enter, then use Up and Down to set the desired DMX mode
(5x5 Model CH 03, CH 05, CH 09,CH 75, CH80
4x4 Model - CH 03, CH 05, CH 09, CH48, CH53
, press "Enter" again to confirm.
Dimmer Speed Setting:
After select the "Dimmer Curve" and press Enter, then use Up and Down to set the desired dimmer speed
(01, 02, 03, 04), press "Enter" again to confirm.
Sound Mode
Entered "Sound mode", use <UP> and <DOWN> to set the sensitivity Sen 000 ~ Sen 100, press Enter to confirm.
Setting Static Colors
Entered "Static Color", you can select the desired solid color via the UP or DOW N buttons and confirm by Enter
Mode:
Value:
Function:
Static Color
Static color <R>
Red
Static color <G>
Green
Static color <B>
Blue
Static color <RG>
Red + Green
Static color <BG>
Green + Blue
Static color <RB>
Red + Blue
Static color <RGB>
Red + Green + Blue

6
User Mode
This mode allows the user set intensity of R, G, B separately to get endless color mixing from the control
board without DMX controller to set the device to run strobe desired.
Entered user mode "Manual color", use <UP> and <DOWN> to select the “R / G / B" for Colors intensity or "S" for strobe.
Use <UP> and <DOWN> to set the colors intensity values " 0 ~ 255" or Strobe speed values "000 ~ 100"
(Freeze, Slow ~ Fast), then press "Enter" to confirm.
Automatic Mode
This fixture has a built-in automatic program.
Entered "Auto Program" mode, use <UP> and <DOW N> to select the built-in programs "Pr01 ~ Pr -12"
then press the "Enter" to confirm.
Use <UP> and <DOWN> to select the operating speed of the program(Value:Speed 000 ~ Speed100, Freeze,Slow ~ Fast),
Mode:
Value:
Function for 4x4 model:
Function for 5x5 model:
Auto
Program
Pr 01
R G B colors switching
R G B colors switching
Pr 02
7 colors switching
7 colors switching
Pr 03
R G B colors fading
Colors Macros Fading
Pr 04
7 colors Fading
Chase 1
Pr 05
Color Macros Fading
Chase 2
Pr 06
Chase 1
Chase 3
Pr 07
Chase 2
Chase 4
Pr 08
Chase 3
Chase 5
Pr 09
Chase 4
Chase 6
Pr 10
Chase 5
Chase 7
Pr 11
Chase 6
Chase 8
Pr 12
Chase 7
Chase 9
Pr 13
Chase 8
Chase 10
Pr 14
Chase 9
Chase 11
Pr 15
Loop above Pro 01~ Pr 14
Chase 12
Pr 16
NA
Loop above Pro 01~ Pr 15
Master/Slave Operation
This mode allows for multiple units slave fixtures to follow a single master fixture.
1) Set the master fixture to one of the standalone operating modes: automatic, sound, user mode or static color modes
2) For slave units, entered the Master/Slave mode, select "Slave", press Enter.

7
DMX VALUES
3 Channels Mode: ALL
CHANNEL
VALUE
FUNCTION
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
5 Channels Mode: ALL
CHANNEL
VALUE
FUNCTION
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
Master Dimmer 0% ~ 100%
5
000-009
No function
010-255
Strobe : Slow ~ Fast(1~30Hz)
9 Channels Mode: ALL
CHANNEL
VALUE
FUNCTION
1
000-255
Red 0% ~ 100%
Warm white 0% ~ 100%
When 169-208 set in CH. 9
2
000-255
Green 0% ~ 100%
Cool white 0% ~ 100%
When 169-208 set in CH. 9
3
000-255
Blue 0% ~ 100%
4
000-255
Master Dimmer 0% ~ 100%
5
000-009
No function
010-255
Strobe : Slow ~ Fast(1~30Hz)
6
000-019
No Function
020-039
RED 100% / GREEN 0% ~ 100% / BLUE 0%
040-059
RED 100% ~ 0% / GREEN 100% / BLUE 0%
060-079
RED 0% / GREEN 100% / BLUE 0% ~ 100%
080-099
RED 0% / GREEN 100% ~ 0% / BLUE 100%
100-119
RED 0% ~ 100% / GREEN 0% / BLUE 100%
120-139
RED 100% / GREEN 0% / BLUE 100% ~ 0%
140-159
RED 100% / GREEN 0% ~100% / BLUE 0%~100%
160-179
RED 100%~ 0% / GREEN 100% ~ 0% / BLUE 100%
180-199
RED 100% / GREEN 100% / BLUE 100%
200-204
White Color Temperature 1
WARM
205-209
White Color Temperature 2
210-214
White Color Temperature 3
215-219
White Color Temperature 4

8
220-224
White Color Temperature 5
225-229
White Color Temperature 6
230-234
White Color Temperature 7
235-239
White Color Temperature 8
240-244
White Color Temperature 9
245-249
White Color Temperature 10
250-255
White Color Temperature 11
COOL
7
000-009
No function
010-032
Auto Program PR 01
R G B colors switching
033-056
Auto Program PR 02
7 colors switching
057-080
Auto Program PR 03
R G B colors fading
081-104
Auto Program PR 04
7 colors Fading
105-128
Auto Program PR 05
Color Macros Fading
129-152
Auto Program PR 06
Chase 1
153-176
Auto Program PR 07
Chase 2
177-200
Auto Program PR 08
Chase 3
201-224
Auto Program PR 09
Chase 4
225-248
Auto Program PR 10
Loop above pr 01~pr 09
249-255
Sound active
8
000-255
Speed / Sensitivity of Auto / Sound Programs (Slow ~
Fast)
9
000-009
Default dimmer speed
010-048
Non-linear dimmer 1
049-088
Non-linear dimmer 2
089-128
Non-linear dimmer 3
129-168
Non-linear dimmer 4
169-208
WW/CW Mode ON
209-255
WW/CW Mode OFF
48 Channels Mode: 4x4
CHANNEL
VALUE
FUNCTION
1,4,7,10,13,16,19,22,25,28,
31,34,37,40,43,46,
000-255
Red 0% ~ 100%
LED 1 (1-3) , LED 2 (4-6), LED 3 (7-9)
LED 4 (10-12), LED 5 (13-15) , LED 6 (16-18)
2,5,8,11,14,17,20,23,26,29,
32,35,38,41,44,47
000-255
Green 0% ~ 100%
LED 7 (19-21) , LED 8 (22-24), LED 9 (25-27)
LED 10 (28-30) , LED 11 (31-33), LED 12 (34-36)
3,6,9,12,15,18,21,24,27,30,
33,36,39,42,45,48
000-255
Blue 0% ~ 100%
LED 13 (37-39) , LED 14 (40-42), LED 15 (43-45)
LED 16 (46-48)

9
53 Channels Mode: 4x4
CHANNEL
VALUE
FUNCTION
1,4,7,10,13,16,19,22,25,28,
31,34,37,40,43,46,
000-255
Red 0% ~ 100%
LED 1 (1-3) , LED 2 (4-6), LED 3 (7-9)
LED 4 (10-12), LED 5 (13-15) , LED 6 (16-18)
2,5,8,11,14,17,20,23,26,29,
32,35,38,41,44,47
000-255
Green 0% ~ 100%
LED 7 (19-21) , LED 8 (22-24), LED 9 (25-27)
LED 10 (28-30) , LED 11 (31-33), LED 12 (34-36)
3,6,9,12,15,18,21,24,27,30,
33,36,39,42,45,48
000-255
Blue 0% ~ 100%
LED 13 (37-39) , LED 14 (40-42), LED 15 (43-45)
LED 16 (46-48)
49
000-255
Master Dimmer 0% ~ 100%
50
000-009
No function
010-255
Strobe :
Slow ~ Fast(1~30Hz)
51
000-009
No function
010-023
Auto Program PR 01
R G B colours switching
024-038
Auto Program PR 02
7 colours switching
039-053
Auto Program PR 03
R G B colours fading
054-068
Auto Program PR 04
7 colours Fading
069-083
Auto Program PR 05
Colour Macros Fading
084-098
Auto Program PR 06
Chase 1
099-113
Auto Program PR 07
Chase 2
114-128
Auto Program PR 08
Chase 3
129-143
Auto Program PR 09
Chase 4
144-158
Auto Program PR 10
Chase 5
159-173
Auto Program PR 11
Chase 6
174-188
Auto Program PR 12
Chase 7
189-203
Auto Program PR 13
Chase 8
204-218
Auto Program PR 14
Chase 9
219-233
Auto Program PR 15
Loop above Pro 01~ Pr 14
234-255
Sound active
52
0000-255
Speed/Sensitivity of Auto /
Sound Programs
(Slow ~ Fast)
53
000-009
Default dimmer speed
010-048
Linear dimmer
049-088
Non-linear dimmer 1
089-128
Non-linear dimmer 2
129-168
Non-linear dimmer 3
169-208
WW/CW Mode ON
209-255
WW/CW Mode OFF
When CH 53 @ 169-208, WW/CW ON, CH 1 ~ CH 32 function as fol lowing:
1,3,5,7,9,11,13,15,
17,19,21,23,25,27,
29,31
000-255
Warm white 0% ~ 100%
LED 1 (1,2), LED 2 (3,4), LED 3 (5,6),
LED 4 (7,8), LED 5 (9,10), LED 6 (11,12),
LED 7 (13,14), LED 8 (15,16), LED 9
(17,18), LED 10 (19,20), LED 11 (21,22),
LED 12 (23,24), LED 13 (25,26), LED 14
(27,28), LED 15 (29,30), LED 16 (31,32),
2,4,6,8,10,12,14,
16,18,20,22,24,26,
28,30,32
000-255
Cool white 0% ~ 100%

10
75 Channels Mode: 5x5
CHANNEL
VALUE
FUNCTION
1,4,7,10,13,16,19,22,25,28,
31,34,37,40,43,46,49,52,55,
58,61,64,67,70,73
000-255
Red 0% ~ 100%
LED 1 (1-3) , LED 2 (4-6), LED 3 (7-9)
LED 4 (10-12), LED 5 (13-15) , LED 6 (16-18)
LED 7 (19-21) , LED 8 (22-24), LED 9 (25-27)
2,5,8,11,14,17,20,23,26,29,
32,35,38,41,44,47,50,53,56,
59,62,65,68,71,74
000-255
Green 0% ~ 100%
LED 10 (28-30) , LED 11 (31-33), LED 12 (34-36)
LED 13 (37-39) , LED 14 (40-42), LED 15 (43-45)
LED 16 (46-48), LED 17 (49-51), LED 18 (52-54)
3,6,9,12,15,18,21,24,27,30,
33,36,39,42,45,48,51,54,57,
60,63,66,69,72,75
000-255
Blue 0% ~ 100%
LED 19 (55-57) , LED 20 (58-60), LED 21 (61-63)
LED 22 (64-66), LED 23 (67-69) , LED 24 (70-72)
LED 25 (73-75)
80 Channels Mode: 5x5
CHANNEL
VALUE
FUNCTION
1,4,7,10,13,16,19,22,25,28,
31,34,37,40,43,46,49,52,55,
58,61,64,67,70,73
000-255
Red 0% ~ 100%
LED 1 (1-3) , LED 2 (4-6), LED 3 (7-9)
LED 4 (10-12), LED 5 (13-15) , LED 6 (16-18)
LED 7 (19-21) , LED 8 (22-24), LED 9 (25-27)
2,5,8,11,14,17,20,23,26,29,
32,35,38,41,44,47,50,53,56,
59,62,65,68,71,74
000-255
Green 0% ~ 100%
LED 10 (28-30) , LED 11 (31-33), LED 12 (34-36)
LED 13 (37-39) , LED 14 (40-42), LED 15 (43-45)
LED 16 (46-48), LED 17 (49-51), LED 18 (52-54)
3,6,9,12,15,18,21,24,27,30,
33,36,39,42,45,48,51,54,57,
60,63,66,69,72,75
000-255
Blue 0% ~ 100%
LED 19 (55-57) , LED 20 (58-60), LED 21 (61-63)
LED 22 (64-66), LED 23 (67-69) , LED 24 (70-72)
LED 25 (73-75)
76
000-255
Master Dimmer 0% ~ 100%
77
000-009
No function
010-255
Strobe :
Slow ~ Fast(1~30Hz)
78
000-009
No function
010-023
Auto Program PR 01
R G B colors switching
024-038
Auto Program PR 02
7 colors switching
039-053
Auto Program PR 03
R G B colors fading
054-068
Auto Program PR 04
7 colors Fading
069-083
Auto Program PR 05
Color Macros Fading
084-098
Auto Program PR 06
Chase 1
099-113
Auto Program PR 07
Chase 2
114-128
Auto Program PR 08
Chase 3
129-143
Auto Program PR 09
Chase 4
144-158
Auto Program PR 10
Chase 5
159-173
Auto Program PR 11
Chase 6
174-188
Auto Program PR 12
Chase 7
189-203
Auto Program PR 13
Chase 8
204-218
Auto Program PR 14
Chase 9
219-233
Auto Program PR 15
Chase 10
234-248
Auto Program PR 16
Loop above Pro 01~ Pr 15
249-255
Sound Active

11
79
0000-255
Speed/Sensitivity of Auto /
Sound Programs
(Slow ~ Fast)
80
000-009
Default dimmer speed
010-048
Linear dimmer
049-088
Non-linear dimmer 1
089-128
Non-linear dimmer 2
129-168
Non-linear dimmer 3
169-208
WW/CW Mode ON
209-255
WW/CW Mode OFF
When CH 80 @ 169-208, WW/CW ON, CH 1 ~ CH 50 function as following:
1,3,5,7,9,11,13,15,
17,19,21,23,25,27,
29,31,33,35,37,39,41
43,45,47,49
000-255
Warm white 0% ~ 100%
LED 1 (1,2), LED 2 (3,4), LED 3 (5,6),
LED 4 (7,8), LED 5 (9,10), LED 6 (11,12),
LED 7 (13,14), LED 8 (15,16), LED 9
(17,18), LED 10 (19,20), LED 11 (21,22),
LED 12 (23,24), LED 13 (25,26), LED 14
(27,28), LED 15 (29,30), LED 16 (31,32),
LED 17 (33,34), LED 18 (35,36), LED 19
(37,38), LED 20 (39,40), LED 21 (41,42),
LED 22 (43,44), LED 23 (45,46), LED 24
(47,48), LED 25 (49,50)
2,4,6,8,10,12,14,
16,18,20,22,24,26,
28,30,32,34,36,38,40
42,44,46,48,50
000-255
Cool white 0% ~ 100%
TECHNICAL SPECIFICATIONS
Model
PAN 4x4x30
PAN 5x5x30
Dimensions and Weight
LxWxH (mm)
425 x 425 x 141
532 x 532 x 226
Weight (kg)
11.3
14.5
Power
Power Supply
100~240VAC, 50/60 Hz
Power Consumption (w)
390
600
Fuse
T 3.15A, 250V
T6A, 250V
LED
16pcs 30W COB Tri-color RGB
25pcs 30W COB Tri-color RGB
Operation Modes
DMX, Auto, SoundActive, Master/Slave, RGBW Manual Control Mode, Static colour Mode
Beam Angle
60°
Refresh Rate
11,700Hz
DMX Channel
3,5,9,48,53 channels
3,5,9,75,80 channels
DMX connection
3 pin & 5 pin XLR
3 pin & 5 pin XLR
Power Input
Neutrik Powercon
Power Output
Neutrik Powercon
Pixel control for each COB LED
LCD display with 4 buttons control
Smooth electronic dimming with a 16-bit 4 Dimmer curve
Oxidation surface treated aluminum Housing
Variable Speed Strobe Effect (1 –30 Hz)
WARRANTY
Please refer to your local dealer or please contact Event Lighting.