Everest 6120 Product manual

OPERATOR AND PARTS MANUAL
6120 SNOWBLOWER

EVEREST MODEL #6120
Page 2of 24
Contents
INTRODUCTION ...................................................................................................................................................................3
SAFETY.................................................................................................................................................................................4
SAFETY DECALS ....................................................................................................................................................................5
GENERAL SAFETY .................................................................................................................................................................6
LIMITED WARRANTY............................................................................................................................................................7
LIMITED WARRANTY -CONTINUED ..................................................................................................................................................8
PREPARATION FOR USE ...........................................................................................................................................................9
PREPARATION FOR USE –CONTINUED......................................................................................................................................10
OPERATING INSTRUCTIONS ...............................................................................................................................................11
MAINTENANCE ..................................................................................................................................................................12
MAINTENANCE –CONTINUED ..................................................................................................................................................13
PARTS ................................................................................................................................................................................14
PARTS –CONTINUED.................................................................................................................................................................15
PARTS -CONTINUED .................................................................................................................................................................16
PARTS –CONTINUED.................................................................................................................................................................17
PARTS LIST .............................................................................................................................................................................18
PARTS LIST –CONTINUED..........................................................................................................................................................19
PARTS LIST -CONTINUED ..........................................................................................................................................................20
GEARBOX ASSEMBLY .............................................................................................................................................................21
GEARBOX ASSEMBLY –PARTS LIST ........................................................................................................................................22
PTO PARTS .............................................................................................................................................................................23
PTO PARTS LIST......................................................................................................................................................................23
Printed in Canada
10/2014

EVEREST MODEL #6120
Page 3of 24
INTRODUCTION
General Metal Fabrication has been producing high quality farm equipment for over 15 years. Our line
of Everest Snow blowers are manufactured using top quality material and workmanship. We feel
confident that this equipment will meet your expectations in reliability and performance when used as
designed. This manual is to assist you in the safe assembly, maintenance, and operation of the Everest
Snow Blower. It also has a parts list to help you when replacement parts are required. Everest Snow
Blowers are available in a wide range of sizes.
The care you give your Everest product will greatly determine your satisfaction with its performance
and its service life. We urge a careful study of this manual to provide you with a thorough
understanding of your new implement before operating, as well as suggestions for operation and
maintenance and storage.
If this manual should become lost or destroyed we will be glad to provide you with a new copy.
As an authorized Everest manufacturer, we stock genuine Everest parts which are fabricated with the
same precision and skill as our original equipment.
Should you require additional information or assistance please contact us.
THE ILLUSTRATIONS AND INFORMATION CONTAINED WITHIN THIS MANUAL ARE CURRENT AT THE
TIME OF PUBLICATION. EVEREST MAINTAINS AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT,
THEREFORE WE RESERVE THE RIGHT TO MAKE IMPROVEMENTS IN DESIGN OR CHANGES IN
SPECIFICATIONS WITHOUT INCURRING ANY OBLIGATION TO INSTALL THEM ON UNITS PREVIOUSLY
MANUFACTURED.
MODEL:
SERIAL:
DATE OF PURCHASE:
DEALER NAME: ____________

EVEREST MODEL #6120
Page 4of 24
SAFETY
Remember YOU are the key to safety. Do not risk damage to the product, personal injury or death. It is essential
that you read the safety instructions and before you operate this snow blower.
Note: our products are designed to be safe and dependable. It is the owner’s responsibility that anyone
operating this equipment reads and understands this manual and the operation of the equipment before
operating.
SAFETY DECALS
Keep decals clean and readable.
Replace safety decals if damaged and or not readable.
New decals are available from your dealer or manufacturer.
The “Safety Alert Symbol” ( ) in conjunction with a “Signal Word” (CAUTION, WARNING or DANGER) is
used if there is a possible personal injury or death hazard

EVEREST MODEL #6120
Page 5of 24
SAFETY DECALS
To promote safe operation, safety decals are provided on all products manufactured. Because damage
can occur to decals in everyday use or in reconditioning, replacement decals are available. To install
decals make sure the surface is clear and free from oil. Decide on the exact location before removing
backing paper.

EVEREST MODEL #6120
Page 6of 24
GENERAL SAFETY
In addition to the design and configuration of equipment, hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper training of personnel in the operation, transportation,
maintenance and storage of equipment. Lack of attention to safety can result in accident, reduction of
efficiency, personal injury or loss of life. Watch for safety hazards and correct them immediately. Use the
following safety precautions as a general guide to safe operations when operating this machine. Additional
safety precautions are used throughout this manual for specific operating and maintenance procedures. Read
this manual and review the safety precautions often.
Read the instructions carefully. Be familiar with the controls and all the cautions related to this
equipment.
Never allow children, or people not familiar with these instructions to operate this equipment.
Never carry passengers.
The operator is responsible for accidents or hazards occurring to people or property. The operator
should cease operations whenever anyone comes within the operating area.
Clear the work area of objects that might be picked up and thrown.
Do not operate without all guards and shields in place and in good condition.
Before starting or operating the machine, make a walk around inspection and check for obvious defects,
such as loose bolts and damaged components. Correct any problems before starting.
Lower implement to the ground, stop tractor engine, apply parking brake, and allow all components to
completely stop before leaving the tractor.
Keep hands and feet clear of any rotating or moving components.
Wear personal protective equipment such as, but not limited to, protection for the eyes, ears, feet,
hands and head when operating or repairing the equipment. Do not wear loose clothing or jewelry that
may catch on equipment moving parts.
Never stand between implement and tractor while tractor is being backed to the hitch.
When performing maintenance or adjusting implement, first lower it to the ground or block it securely
at a workable height.
Use tractor flashing warning light, day or night, when transporting implement on road or highways
unless prohibited by law.
It is recommended that tractors be equipped with rollover protective systems (ROPS) and seat belts are
used in all operations.

EVEREST MODEL #6120
Page 7of 24
Limited Warranty
This Document limits Your Warranty Rights
Base Limited Warranty
General Metal Fabrication Ltd. provides this warranty only to the original retail purchaser of this product.
General Metal Fabrication Ltd. warrants to such purchasers that all Bauman / Everest manufactured parts and
components used and serviced as provided for in the Operator’s Manuals shall be free from defects in material
and workmanship for a period following delivery to the original retail purchaser of 12 months (90 days for
commercial applications). Parts and components manufactured by others are subject to their manufacturer’s
warranties, if any.
General Metal Fabrication Ltd. will fulfill this limited warranty by, at its’ option, repairing or replacing any
covered part that is defective or is the result of improper workmanship, provided the part or parts are returned
to General Metal Fabrication Ltd. within thirty (30) days of the date that such defect or improper workmanship
is, or should have been, discovered. General Metal Fabrication reserves the right to either inspect the product at
the buyer’s location or have it returned to the factory for inspection. Parts must be returned through the selling
representative and the buyer must prepay transportation charges.
General Metal Fabrication Ltd. will not be responsible for repairs or replacements that are necessitated, in
whole or part, by the use of parts not manufactured by or obtained from General Metal Fabrication Ltd. Under
no circumstances are component parts warranted against normal wear and tear. There is no warranty on
components that require replacement as part of normal maintenance. The purchaser is solely responsible to
determine suitability of goods sold. This warranty is expressly in lieu of all other warranties expressed or
implied. General Metal Fabrication will in no event be liable for any incidental or consequential damages
whatsoever, nor for any sum in excess of the price received for the goods for which liability is claimed.
Repair Parts Limited Warranty
General Metal Fabrication Ltd. warrants Bauman / Everest replacement parts purchased after the expiration of
the General Metal Fabrication Ltd. limited Warranty, and used and serviced as provided for in the Operator’s
Manual, to be free from defects in material or workmanship for a period of thirty (30) days from the invoice date
for the parts. General Metal Fabrication Ltd. will fulfill this limited warranty by, at its option, repairing or
replacing any covered part that is defective or is the result of improper workmanship, provided that the part is
returned to General Metal Fabrication Ltd. within thirty (30) days of the date that such defect or improper
workmanship is, or should have been, discovered. Such parts must be shipped to General Metal Fabrication Ltd.
at the purchaser’s expense.
What is Not Covered?
Under no circumstances does this limited warranty cover any components or parts that have been subject to the
following: negligence; alteration or modification not approved by General Metal Fabrication Ltd.; misuse;
improper storage; lack of reasonable or proper maintenance, service, or repair; normal wear; damage from
failure to following operating instructions; accident; and or repairs that have been made with parts other than
those manufactured, supplied, and or authorized by General Metal Fabrication Ltd.

EVEREST MODEL #6120
Page 8of 24
Limited Warranty - Continued
Authorized Dealer and Labour Costs
Repairs eligible for labour under this limited warranty must be made by General Metal Fabrication Ltd. or an
authorized Bauman / Everest dealer. General Metal Fabrication Ltd. retains the exclusive discretion to
determine whether it will pay labour cost for warranty repairs or replacement, and the amount of such costs
that it will pay and the time in which the repairs will be made. If General Metal Fabrication Ltd. determines that
it will pay labour cost for warranty work, it will do so by issuing a credit to the Dealer’s or Distributor’s account.
General Metal Fabrication Ltd. will not approve or pay invoices sent for repairs that General Metal Fabrication
Ltd. has not previously approved. Warranty service does not extend the original term of this limited warranty.
Warranty Labour
Any labour subject to warranty must be authorized by General Metal Fabrication Ltd. The labour rate for
replacing defective parts, where applicable, will be credited at 100% of the dealer’s posted shop rate.
Warranty Requirements
If the Dealer or Distributor decides to purchase replacement components before the warranty disposition of
such components is determined, General Metal Fabrication Ltd. will bill the customer for such components and
then credit the replacement invoice for those components later determined to be covered by this limited
warranty. Any such replacement components that are determined not to be covered by this limited warranty
will be subject to the terms of the invoice and shall be paid for by the purchaser.
Warranty Claims
Warranty requests must be prepared on General Metal Fabrication Ltd. warranty Claim Forms with all requested
information properly completed. Warranty Claims must be submitted within a thirty (30) day period from date
of failure repair.
Exclusive Effect of Warranty and Limitation of Liability
To the extent permitted by the law, General Metal Fabrication Ltd. disclaims any warranties, representations, or
promises express or implied, as to the quality, performance, or freedom from defect of the components and
parts covered by this warranty and not specifically provide for herein.
To the extent permitted by law, General Metal Fabrication Ltd. disclaims any implied Warranties of
merchantabilities and fitness for a particular purpose on its products covered herein, and disclaims any reliance
by the purchaser on General Metal Fabrication Ltd. skill or judgment to select or furnish goods for any particular
purpose. The purchaser’s only and exclusive remedies in connection with the breach or performance of any
warranty on product manufactured by General Metal Fabrication Ltd. are those set forth herein. In no event
shall General Metal Fabrication Ltd. be liable for incidental or consequential damages (including by way of
example only and not limitation, loss of crops, loss of profits or revenue, other commercial loss, inconvenience,
or cost of replacement of rental equipment). In no event shall General Metal Fabrication Ltd. contract or
warranty liability exceed the purchase price of the product.
Note: Snowblower fan shafts and Finishing Mower blades carry no warranty.

EVEREST MODEL #6120
Page 9of 24
PREPARATION FOR USE
Connecting to tractor
Make sure the tractor and the snow blower are on level dry ground free from foreign objects.
Move tractor to snow blower slowly making sure no person or pet is between tractor and implement.
Adjust the three point arms to be parallel with the lift pins.
Set the parking brake, remove ignition key before dismounting the tractor.
Attach the three point arms to the lift pins and locks in place with lynch pins provided.
Fasten the top arm of the tractor to the link pin in the hitch weldment.
With the tractor engine shut off, fasten the PTO shaft; both ends of the PTO have a standard 20-spline
end with a spring loaded locking collar. To activate the spring loaded locking collar turn the collar
clockwise, then slide onto the splined shaft. The yoke must lock into the groove of the splined shaft on
the tractor and the gearbox. Always check to see that the yokes are securely attached before each use.
Fasten the safety chains provided with the PTO shaft, allowing sufficient slack for the driveline during
cornering and operations.
NOTE: Due to the many variations in tractor hitches and PTO locations, drivelines may need to be
shortened to ensure proper length.
oPull driveline apart. Attach outer (Female) section to the tractor PTO shaft, making sure they are
secure.
oRaise and lower implement to determine shortest distance between tractor PTO and snow
blower input shaft. Shut down tractor leaving implement in position of shortest distance.
SECURELY BLOCK IMPLEMENT IN POSITION.
oHold driveline sections parallel to each other to determine if it is too long. Each section should
end approximately 3 inches short of reaching universal joint shield on opposite section.
oIf the required driveline length is greater than length of the shaft, move the hitch mounting
locations on the snow blower until the correct position is achieved.
oIf the drive line is still too long measure 3 inches back from universal joint shield and mark
opposite section. Do this for both sections.
oRaise and lower snow blower to determine longest position between tractor PTO and snow
blower input shaft. Shut down tractor and securely block snow blower in position.
oHold the drive line parallel to each other and check for a minimum of 6 inch overlap. If driveline
has been marked for cutting the overlap will be the distance between marks. NOTE: if driveline
is the correct length disregard cutting procedures.

EVEREST MODEL #6120
Page 10 of 24
PREPARATION FOR USE –Continued
oClamp end of driveline in vice. Cut off shield where marked. Using the cut off section of shield as
a guide, cut shaft the same amount. NOTE: when finished cutting, the shield will be shorter than
the shaft. Deburr driveline sections and clean away all chips and filings.
oRepeat cut procedure to other driveline section.
oApply multi-purpose grease to outside of male driveline section. Assemble driveline and install
onto tractor and snow blower. Pull on each driveline section to ensure yokes lock into position.
Make sure driveline shielding is in place and in good condition.
Start the engine, and raise the snowblower slightly.
Adjust the three point hitch arms to level, and center the snow blower behind the tractor.
Adjust the turnbuckle on the top of the three point hitch to level the snow blower from front to back.
SKID SHOES
After attaching the tractor to the snow blower, ensure that the snow blower cutting edge is parallel to the
ground when skid shoes are touching the ground. If not, adjust the skid shoes accordingly.
If the surface is soft / uneven or contains gravel, stones or other material that might be easily picked up
and thrown by the snow blower, then a lower position should be used, thereby increasing the working
clearance between the surface and the cutting edge.
If the surface is hard and smooth like concrete or asphalt, skid shoes should be placed in the highest
position to minimize residual snow following each pass.
Before performing maintenance or adjustments to the skid shoes refer to general safety page 7 of this
manual.
Skid shoes must be adjusted so they contact the ground evenly on both sides. Finer adjusting can be
done using the top link of the 3 point hitch so that the skid shoes have full contact with the surface and
the cutting edge is parallel to the ground.

EVEREST MODEL #6120
Page 11 of 24
OPERATING INSTRUCTIONS
Check before each use
Check tightness of chain, bolts, and other hardware.
Clear the work area of anything that might be thrown, and check to ensure all bystanders are standing
clear before starting.
Field operation
With the tractor running at slow idle engage the PTO control. Slowly increase the tractor engine RPM to
achieve the rated PTO speed. Never exceed the rated speed.
The PTO must run at a full PTO rpm rating for best performance. Slower drive speeds or multiple passes
could be required for wet snow.
Travel speed is governed by the operating conditions including the depth of the snow, the density
(wetness) and the area being cleared including the surface and slopes. It is the responsibility of the
operator to note the condition of the job being done and set the speed to obtain the proper clearing
rate to maintain safe control of machine.
The PTO driveline is equipped with a shear bolt that protects the drive system components from shock loads if
the machine strikes an obstruction. See parts section for appropriate replacement part.
Operational hints
Always ease the implement slowly into the snow. Do not allow engine of the tractor to lug or stall.
In deep or heavy snow you may need to remove snow in several passes.
Remember to disengage the PTO when raising or lowering the snow blower
DO NOT USE THE SNOW BLOWER TO PUSH SNOW- always engage snow with the snow blower
operating.
Disconnecting from tractor
Park on firm level area and clean the snow blower.
Lower the snow blower until the tension is removed from hitch area.
Disconnect the hitch arms and PTO shaft.
Relieve any hydraulic pressure and remove hose from tractor.
Cover the snow blower or store indoors to prevent rust.

EVEREST MODEL #6120
Page 12 of 24
MAINTENANCE
Always ensure the snow blower is properly installed, tractor is positioned on level
ground with the park brake on, and the snow blower positioned on the ground. Shut off
the engine remove and retain ignition key. Release any hydraulic pressure before
performing any maintenance.
Check list before each use
Inspect fan blades and flighting to be sure no foreign objects such as wire or rope are wrapped around
them.
After 8 hour of use.
oGrease PTO crosses daily (or 8 hours of operation) with multi-purpose grease. In extreme PTO
angle applications cross kits must be greased more frequently.
oPTO driveline shield –Apply 2-3 shots of multi-purpose grease on plastic fitting.
After 100 hours of use.
oGrease all bearings with multi-purpose grease. DO NOT OVER GREASE.
After 500 hours of use
oThe gearbox should be filled with SAE 90 oil to the bottom of level plug when shipped. Check
the gearbox before using, at regular intervals. See that this oil level is maintained.

EVEREST MODEL #6120
Page 13 of 24
MAINTENANCE –Continued
BOLT TORQUE
The following ft-lbs torque values are advisory only. Extreme caution should be used when using
torque/tension relationships. Torque is only an indirect indication of tension. Under/over tightening of
fasteners can result in costly equipment failure and/or personal injury.
No two bolts respond exactly the same to a given torque. There are numerous "real world"
complications. Things such as dirt in a tapped hole, grease or oil on the threads, damaged threads, hole
misalignment, accuracy of torque measuring device, and numerous other factors can alter the torque-
tension relationship. Even perfect input torque can give a variation of preload by as much as 25%.
Bolt
Diameter
Thread
Series
SAE2
SAE5
SAE8
Oiled
As
Received
Dry
Oiled
As
Received
Dry
Oiled
As
Received
Dry
1/4”
UNC
2.7
3
3.6
6.3
7.2
8.5
8.9
10.1
11.9
UNF
3.1
3.5
4.1
7.2
8.2
9.7
10.2
11.6
13.6
5/16”
UNC
5.5
6.3
7.4
13.1
14.8
17.4
18.4
20.9
24.6
UNF
6.1
6.9
8.2
14.5
16.4
19.3
20.4
23.1
27.2
3/8”
UNC
10
11
13
23
26
31
33
37
44
UNF
11
13
15
26
30
35
37
42
49
7/16”
UNC
16
18
21
37
42
49
52
59
70
UNF
18
20
23
41
47
55
58
66
78
1/2”
UNC
24
27
32
57
64
75
80
91
106
UNF
27
31
36
64
72
85
90
102
120
9/16”
UNC
35
39
46
82
92
109
115
131
154
UNF
39
44
51
91
103
121
128
146
171
5/8”
UNC
48
54
64
113
128
150
159
180
212
UNF
54
61
72
128
145
170
180
204
240
3/4”
UNC
85
96
113
200
227
267
282
320
376
UNF
94
107
126
223
253
297
315
357
420
7/8”
UNC
136
155
182
322
365
429
455
515
606
UNF
150
171
201
355
403
474
502
568
669
1”
UNC
204
232
273
483
547
644
682
772
909
UNF
229
260
306
542
614
722
766
867
1020
All Values are in foot-pounds. To convert foot-pounds to inch-pounds, multiply by 12.

EVEREST MODEL #6120
Page 14 of 24
PARTS

EVEREST MODEL #6120
Page 15 of 24
PARTS –Continued

EVEREST MODEL #6120
Page 16 of 24
PARTS - Continued

EVEREST MODEL #6120
Page 17 of 24
PARTS –Continued

EVEREST MODEL #6120
Page 18 of 24
PARTS LIST
ITEM
PART NO.
DESCRIPTION
1
109598
BODY
2
109637
SERRATED AUGER
3
108542
AUGER
4
109618
FAN WELDT
5
109629
SPOUT
6
104975
ROLLER CHAIN
7
108317
HITCH
8
108503
HITCH LOWER EXTENTION
9
108508
HITCH LOWER EXTENTION
10
108544
SKID SHOE
11
108556
HITCH STAND
12
108558
SPOUT ROTATOR DRIVE SPROCKET
13
108561
TORSION SPRING BRACKET
14
109624
FLIGHTING DRIVE SHAFT
15
109628
SHEAR SPROCKET
16
109652
GEARBOX ASSY.
17
104294
3 POINT HITCH TOP BRACE
18
105233
RESTRICTOR
19
105832
FLIGHTING DRIVE END PLATE
20
108523
SPOUT ROLLER
21
108545
SPOUT DRIVE SHIELD
22
108563
TORSION SPRING SPACER
23
108565
CHAIN SIDE COVER
24
108575
SPRING HOLDER BAR
25
108640
KEY
26
109622
SHEAR BOLT ACCESS COVER
27
109623
UHMW WEAR PLATE
28
109649
PTO SHIELD
29
109650
FLIGHTING DRIVE SHAFT SHIELD
30
109651
RETAINING WASHER
31
109677
KEY
32
109903
SPROCKET
33
109904
SPROCKET
34
109964
KEY
35
10000253
BEARING, ASSEMBLY
36
10000714
BOLT, HEX, STEEL, GR. 5, PLTD, 1/2-13 NC X 1-1/2
37
10000716
BOLT, HEX, 1/2-13NC X 1-3/4
38
10000717
BOLT, HEX, STEEL, GR. 5, PLTD, 1/2-13NC X 2"
39
10000745
BOLT, HEX, STEEL, GR. 5, PLTD, 1-8 NC X 5-1/2"

EVEREST MODEL #6120
Page 19 of 24
PARTS LIST –Continued
40
10000749
BOLT, HEX, STEEL, GR5, PLTD, 3/4-10NC X 2
41
10000757
BOLT, HEX, STEEL, GR. 5, PLTD, 3/8-16 NC X 1"
42
10000758
BOLT, HEX, 3/8-16 NC X 1-1/2
43
10000763
BOLT, HEX, STEEL, GR. 5, PLTD, 3/8-16 NC X 3/4"
44
10000764
BOLT, HEX, STEEL, GR. 5, PLTD, 5/16-18NC X 1
45
10000767
BOLT, HEX, STEEL, GR. 5, PLTD, 5/16-18 NC X 2"
46
10000770
BOLT, HEX, GR5, PL, 5/16-18NC X 3/4
47
10000773
BOLT, HEX, GR5, PL, 5/8-11NC X 1-3/4
48
10000774
BOLT, HEX, GR5, PL, 5/8-11NC X 2
49
10000778
BOLT, HEX, GR5, PLTD., 5/8-11NC X 3-1/2
50
10000801
BOLT, HEX, STEEL, GR. 8, PLTD, 1/2-13 NC X 1-3/4
51
10000852
BOLT, HEX, STEEL, GR. 5, PLTD, 5/8-11NC X 2-1/2
52
10001078
CLIP, HITCH PIN, #11, Ø7/16-3/4" x 1/8" WIRE
53
10001102
NUT, HEX, GR. 2, 1/2-13 NC
54
10001109
NUT, HEX, STOVER, GR. 2 1-14
55
10001113
NUT, HEX, GR. 2, 3/8-16 NC
56
10001114
NUT, HEX, GR.2, PL, 5/16-18 NC
57
10001115
NUT, HEX, GR. 2, 5/8-11 NC
58
10001120
NUT, HEX, GR. 8, 1/2-13 NC
59
10001236
NUT, WING, PLTD, 5/16-18 NC
60
10001268
PIN, LYNCH, 7/16
61
10001321
SET SCREW, SOCKET, CUP POINT, 1/2-13NC X 1"
62
10001326
SET SCREW, SOCKET, CUP POINT, 3/8-16 NC X 1"
63
10001390
WASHER, FLAT, USS, PLTD, 3/8"
64
10001391
WASHER, FLAT, USS, PLTD, 5/8"
65
10001419
WASHER, FLAT, 1"
66
10001420
WASHER, FLAT, SAE, 1/2"
67
10001422
WASHER, FLAT, SAE, 3/8"
68
10001431
WASHER, LOCK, 1/2"
69
10001435
WASHER , LOCK 3/4"
70
10001436
WASHER, LOCK, 3/8"
71
10001437
WASHER, LOCK, 5/16"
72
10001438
WASHER, LOCK, 5/8"
73
10001792
SWIVEL 90 DEG. #6 MALE #4FP FEMALE
74
10002564
TORSION SPRING
75
10003082
SPROCKET, IDLER
76
10004215
BUSHING, OILLITE
77
10004216
BOLT, PLOW, STEEL, GR. 5, PLTD, 1/2-13 NC X 1-1/2"
78
10005613
HOLDER, MANUAL 3-1/2" DIA.
79
10005615
DECAL, SERIAL NUMBER

EVEREST MODEL #6120
Page 20 of 24
PARTS LIST - Continued
80
10005616
DECAL, WARNING, MUST NOT OPERATE
81
10005623
DECAL, WARNING AVOID INJURY OR DEATH
82
10005624
DECAL, WARNING DO NOT GO NEAR LEAKS
83
10005626
DECAL, DANGER AVOID INJURY
84
10005627
DECAL, CAUTION READ OPERATION MANUAL
85
10007298
NUT, HEX, GR2, PL, 3/4-10NC
86
10007445
WASHER, FLAT, SAE, STEEL, PLTD. 5/16"
87
10007523
CYLINDER, HYDRAULIC
88
10007893
HOSE ASSEMBLY
89
10007895
HOSE ASSEMBLY
90
10007899
HYDRAULIC MOTOR
91
10008139
PIN, CLEVIS - ZINC PLATED 1" X 5-1/2"
92
10008140
PIN, CLEVIS - ZINC PLATED 1/2" X 1-1/2"
93
10008153
PIN, CLEVIS - ZINC PLATED 1/2" X 3"
94
10008155
PIN, TOP LINK CAT. 2
95
10008166
PIN, DRAW, CLEVIS TYPE CAT. 2 & 3
96
10008183
BUSHING, LIFT PIN CAT. 2 - 3
97
10008184
BUSHING, TOP LINK CAT. 2 - 3
98
10008493
CUTTING EDGE
99
10008736
PTO SHAFT, STD.
100
10008879
BEARING, ASSY, 4 BOLT FLANGE, 2"
101
10008920
BUSHING, BRONZE
102
10009004
HAIR PIN CLIP #10 BP-210
103
10010878
DECAL, WARNING ENSURE SAFTEY, 1000RPM
104
10011194
DECAL, EVEREST