Evo-lite AMBIENTECH TONE-WS-SA-EVO Series User manual

1
Installation Instructions
Smart Wall Switch Installation
1. Make sure that the ends of the wires from the wall box
are straight (cut if needed).
2. Strip the wire insulator for each wire
inside the wall box as shown here:
Strip the wire insulation from each wire.
Strip 5/8”(1.6 cm)
Wall Box
1. A standard single-gang wall box sized 3 x 2 x 2 ½ cm will service Dimmer
2. Not compatible with multi or double Mud Rings.
3. When using a retrofit gang box (cut in box) you might need
to recess the ears.
Wiring Option 1
Electrical Connection
Red
Green Ground
Black
Neutral
White
Line / Hot
120
V~
5
0/60 Hz
Wall Switch
(In-Wall Dimmer)
LED Driver
(Load)
LED Indicator LED Indicator
Wiring Option 2
Stand-alone Wall Switch
Before You Begin
To avoid fire, shock, or death, turn the
power Off at circuit breaker and test to
ensure the power is Off before wiring.
ON
OFF
P/N:TONE-WSx-SA-EVO
WARM-WSx-SA-EVO
TECH-WSx-SA-EVO
Red
Green Ground
Black
Neutral
White Pair Button
Line / Hot
120 V~
50/60 Hz
Wall Switch
(In-Wall Dimmer)
LED Driver
(Load)
Pair /
Reset
Button
Pair /
Reset
Button
Provided by
www.evo-lite.com
1. Make sure all sliders are set to the top and the Wall Switch
is in the OFF position.
2. Turn the power ON at the circuit breaker.
3. Press the Pair button on all drivers that will be synced to
this Wall Switch.
Please Note: You have 5 minutes from the moment the
first driver’s button is pressed to complete the sync to the
wall switch before the signal times out.
4. Turn ON the Wall Switch and press the Pair / Reset button
on the Wall Switch.
5. The green LED indicator will blink while pairing.
6. Within 15 seconds your LED fixture will be paired with the
Wall Switch.
7. To verify that pairing was successful, move the sliders and
ensure that the connected lighting product responds
accordingly.
1. Make sure all sliders are set to the top and the Wall Switch
is in the OFF position.
2. Switch the power ON at the circuit breaker.
3. Turn ON the Wall Switch and press its Pair / Reset button.
The green LED indicator will blink while pairing.
4. The pairing process will be completed within 15 seconds.
5. To verify that pairing was successful, move the sliders and
ensure that the connected lighting product responds
accordingly.
6. If the Wall Switch is not functioning correctly, set all Wall
Switch sliders to the top, turn ON the Wall Switch, then
press its Pair / Reset button. The connection will be
refreshed and corrected within 15 seconds.
If you are installing more than one Wall Switch unit, all
others must be switched OFF while pairing.*
If you are installing more than one Wall Switch unit, all
others must be switched OFF while pairing.*
If pairing is unsuccessful, please repeat the pairing process.
Factory Reset
Resetting products is not required. Once the Pair / Reset button is pressed it
will override any previous sync settings.
*Please note: 3-way multiswitch operation is currently unavailable.
Download the SmartAir App
Scan the QR code to download the smart device
app. Follow the instructions to connect your lights
to the SmartAir App.
EVO-LITE, LLC. � ARVADA, COLORADO
WWW.EVO-LITE.COM � [e-mail] � 888-887-2980 � V3922

2
Installation Instructions
Customer Assistance
For more info
For technical questions regarding the installationoroperation
of this product, please contact our customer support team:
www.ambientechinc.com
347-334-6368 ext 3
Caution
To reduce the risk of overheating and possible damage to
other equipment, do not install to control a receptacle,
A motor-operated appliance, or a transformer-supplied
appliance.
"GRADATEURS COMMANDANT UN BALLAST - AFIN DE
REDUIRE LE RISQUE DE SURCHAUFFE ET LA POSSIBILITE
D'ENDOMMAGEMENT A D'AUTRES MATERIELS, NE PAS
INSTALLER POUR COMMANDER UNE PRISE, UN APPAREIL A
MOTEUR,"
FCC/IC Information
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Troubleshooting
Wall Switch LED
Indicator blinking
RED
The pairing / reset
button is pressed
while the wall switch
is off
Turn ON the Wall Switch
and press the Pairing
button again
Wall Switch
LED Indicator
steady RED
The Wall Switch is
trying to perform
pairing
Turn ONthe
Wall Switch until
paring is completed
Lights do not
respond to
Wall Switch
The Breaker is Off
or tripped
Turn power ON at
the Circuit breaker
Improper pairing Perform “Pairing”
Improper wiring Make sure all wires
are connected
according to the
wiring diagram
Short circuit at
the LED Driver
output
Check LED Driver
output for short
circuits
Symptoms Cause Possible Solution
The wall switch is
controlling
the wrong lights
(Only if multiple
Wall Switches units are
installed in the
same location)
The Wall Switch was
paired with the
wrong LED Driver
Perform “Pairing”.
Make sure all the other
Wall Switches are turned
Off while pairing
Wall Switch / LED Driver
Replacement
Any reason Perform “Pairing”.
Make sure all the other
Wall Switches are
turned Off while
pairing
EVO-LITE, LLC. � ARVADA, COLORADO
WWW.EVO-LITE.COM � [e-mail] � 888-887-2980 � V3922