Evotech Performance KAWASAKI ZX6R 2007/8 User manual

Standard Conditions of Sale
The catalogue description and any exhibition of samples are only broad indications of the Products and Drury
Precision Engineering Limited may make design changes which do not diminish their performance or visual appeal and
supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the
Products other than those in Drury Precision Engineering Limited order or confirmation and the Buyer confirms it has
chosen the Products as being of merchantable quality and suitable for its particular purposes.
The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the products.
On return of any defective Products Drury Precision Engineering Limited shall at its option either supply a replacement
or refund the purchase money but shall not be liable if the Products have been modified or used or maintained
otherwise than in accordance with Drury Precision Engineering Limited instructions and good engineering practice or if
the defect arises from accident or neglect.
Other than identified above and subject to Drury Precision Engineering Limited not limiting its liability for causing death
and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to
the amounts paid by the Buyer for the Products.
These terms do not affect the Buyer’s statutory rights.
If you require any further information, then please contact us:
Phone: UK Callers: 0800 634 2801
International Callers: [phone]
Fax: [phone]
Email: [e-mail]
Please note that the above is for your information only and does not constitute the Terms and Conditions of your
purchase. These can be found on our website www.evotech-performance.com. If you do not have internet access,
you can obtain our Terms and Conditions by writing to us at the above address.
Returns, Refunds and Replacements
We hope you are happy with your purchase from Evotech Performance. However, if you wish to return or replace a
product, then please carefully read the information and follow the instructions below before sending back your item.
If, within 30 days, you wish to return a product that is not faulty, we will be happy to accept it back, providing that it is
undamaged and in a re-sellable condition. You will have to pay the return postage and we will discount your refund by
a 10% re-packaging and re-stocking fee. We will not refund the original postage.
If the product is faulty, or the wrong part, or any other reason that is our fault we will also refund the return postage
costs.
In either event, please ask for advice when you wish to return anything by calling 0800 634 2801 or by emailing
[e-mail], we will advise the best method of returning it.
If a product should develop a fault after 30 days, please contact us to discuss.
Please let us know why you wish to return the product.
If you are returning faulty goods, you are entitled to a refund or a replacement part. Please indicate which you prefer.
Please ensure that the goods are packed securely, and include all of the original parts, using the original packaging
where possible. If necessary place in suitable extra packaging to protect the goods whilst in transit to us.
Please make sure that you obtain and retain Proof of Posting Certificate from the Post Office when you return your
goods. This is to protect you in the event that your goods are lost in transit; they remain your responsibility until they
reach us.
Returns Address:
Evotech Performance, Beechings Way, Alford, Lincolnshire, LN13 9JE, United Kingdom.
Installation Instructions
Product Reference –5469
www.evotech-performance.com

Kit contents
1 x Reflector Bracket 2 x M5 Nyloc Nuts/Washers
1 x Reflector 2 x M4 x 8 C/Sunk Screws
1 x R/H Bracket 3 x Female Connectors
1 x L/H Bracket (4 small holes for cable ties) 3 x Male Connectors
1 x Rear Light Assembly (including fittings) 4 x M6 x 16 Black b/h screw
1 x Back Plate 4 x M6 Black Washers
2 x Number Plate Screws & Nuts 6 x Cable Ties
Fitting Instructions
1. Remove the pillion seat.
2. Remove L/H and R/H side panels (screws and pull out).
3. Remove front seat (screws).
4. Remove rear body panel (7 screws). Flex carefully and lift to one side.
5. Loosen screws in R/H exhaust cover. Remove L/H exhaust cover (2 screws on
top) VERY CAREFULLY EASE FORWARD AND OFF -Very small tags along
rear seam.
6. Remove small panel over rear light by pushing in centres of plastic plugs and lift
away.
7. Remove L/H and R/H indicators (3 screws) and unplug connectors.
8. Remove indicator mounting plate (2 screws).
9. Disconnect rear lights, remove rear light/number plate assembly (2 screws each
side).
10. Fit R/H bracket to exhaust and tighten using 2 screws/washers supplied.
11. Loop 2 cable ties to L/H bracket from outer side and loosely attach
bracket to exhaust.
12. Assemble indicators to back plate, insert 2 cable ties loosely from the
inside of the bracket.
13. Offer up back plate to mounting brackets, feed R/H indicator wire
through cable ties across and out through L/H bracket. Support bracket.
14. Offer up rear light, pass wires through rear plate, through L/H cable tie
and out through L/H bracket. Tighten cable ties on back plate and fix
rear light using two nuts and washers supplied.
15. Pass the wires up through the big hole in L/H bracket, through cable
ties neatly and tighten cable ties, at this point tighten L/H bracket
fixing screws.
16. Fix back plate to mounting brackets using 2 c/sunk screws supplied.
17. Re: connect indicators.
18. Connect rear light wires using connectors supplied, as follows:
REAR LIGHT ASSEMBLY BIKE
RED----------------Brake light----------------Blue/Red
BLACK------------Earth------------------------Black/yellow
YELLOW---------Rear Light------------------Red
(ignore stock connector for old number plate light as it is now illuminated
by rear light)
Check lights and indicators work correctly and wire routing and all fixings
are tight.
19. Reassemble, reversing steps 1-5. Fit number plate and apply reflector
to rear of machine.
Please visit: www.evotech-performance.com
to view our full product range