Extraflame 002272512 User manual

scheda elettronica - Mother board - carte életronique - elektronishe steuerkarte - tarjeta electrónica
002272512
Lucrezia idro TecHNicaL MaNuaL
MaNuaL reserved To auTHorised afTer-saLes service

2

3
index
INDEX
COnTROL BOARd....................................................................................................................................................................... 4
CONTROL BOARD.............................................................................................................................................................................................................4
DISPLAY ICONS KEY.........................................................................................................................................................................................................4
USeR MenU................................................................................................................................................................................. 5
STRUCTURE OF THE USER MENU...............................................................................................................................................................................5
SET TEMPERATURE...........................................................................................................................................................................................................6
SET REGULATIONS............................................................................................................................................................................................................6
STATUS..................................................................................................................................................................................................................................6
USER MENU ........................................................................................................................................................................................................................7
TeCHniCiAn PROGRAMMinG .................................................................................................................................................. 8
PROGRAMMING STRUCTURE ......................................................................................................................................................................................8
inSTALLeR PARAMeTeRS.......................................................................................................................................................... 9
GENERAL DATA .................................................................................................................................................................................................................9
FACTORY SETTINGS.........................................................................................................................................................................................................9
WATER PARAMETERS.....................................................................................................................................................................................................10
WATER PARAMETERS.....................................................................................................................................................................................................10
CHIMNEY TYPE.................................................................................................................................................................................................................11
CONTROLS ACTIVE.........................................................................................................................................................................................................11
INSTALLER..........................................................................................................................................................................................................................12
inSTALLeR FUnCTiOnS...........................................................................................................................................................12
OUTPUTS TEST.................................................................................................................................................................................................................12
COUNTERS.........................................................................................................................................................................................................................13
ALARMS MEMORIES ......................................................................................................................................................................................................13
DEFAULT .............................................................................................................................................................................................................................14
RESET PART HOURS .......................................................................................................................................................................................................14
AIR DISCHARGE...............................................................................................................................................................................................................15
UNLOCK..............................................................................................................................................................................................................................15
VARiOUS COnTROLS ...............................................................................................................................................................16
ALARM MEMORY RESET...............................................................................................................................................................................................16
FEED.....................................................................................................................................................................................................................................16
FLOW RATE CONTROL...................................................................................................................................................................................................16
ALARMS ....................................................................................................................................................................................17
diSPLAYS ..................................................................................................................................................................................18
MAinTenAnCe.........................................................................................................................................................................22
TROUBLeSHOOTinG................................................................................................................................................................23

4
control board
display icons key
Indicates the presence of an alarm.
On: indicates the presence of an alarm
O: indicates the absence of alarms
Flashing: indicates the deactivation of the depression
sensor.
It indicates functioning of the fumes motor.
O = fumes motor not working
On = fumes motor working
Flashing = breakdown
On = H2O T° lower than desired set
O = H2O T°higher that set-point set
Pump inside the boiler
o = circulator not operating
On = pump running
Ign-plug
O = ign-plug active
On = ign-plug deactivated
Flashing = Ignition phase
not used
Chrono
Indicator on = Chrono on
Indicator o = Chrono o
Not used in the basic LP conguration.
It works only when combined with the additional
system board.
stby = the LED is always activated by default Input STBY status
O = open contact/On = closed contact
not used
LP does not have the remote control.
Ignite with the motor reducer functioning When the
motor feeds, the LED switches on. When the motor
does not feed, the LED switches o.
TEMPERATURE
SETTING OPERATION POWER
ADJUSTMENT
BUTTON
ON/OFF
DISPLAY OF VARIOUS
TEXT MESSAGES DISPLAY
OF POWER
control board

5
structure of the user menu
P5
SAVE  EXIT MENU
MODIFY SETTING DATA: INCREASE P3; DECREASE P2
BROWSING PARAMETERS: NEXT P5 ; PREVIOUS P4
P1
P2 P3
P4 P5
temperature
set regulations
status
user menu
SET H2O
SET PUFFER MAX
SET BOILER MAX
STOVE STATUS
ENABLE CHRONO
BIOMASS
BIOMASS/AUX
AUX
SUMMER/WINTER
BOILER STATUS
SET CLOCK
technician menu
CODE A0
P5
P5
P5
P5
P5
installer functions
installer - par
P3
GENERAL DATA
FACTORY SETTINGS
PAR. CLEANING
WATER PARAMETER
CHIMNEY TYPE 77
CONTROLS ACTIVE
INSTALLER
OUTPUTS TEST
COUNTERS
ALARMS MEMORIES
DEFAULT O1
RESET PART HOURS 77
AIR DISCHARGE 77
UNLOCK 77
RESET ALARM MEMORIES 77
P3
P5 P5
P5
PUFFER STATUS
ENABLE/DISABLE
BOILER CHRONO
PELLETS
HEAT. STATUS SET PUFFER MIN
SET BOILER MIN
LANGUAGE
SET CHRONO
All windows in lighter colour are
managed by the additional board.
The highlighted windows represent
the menus that are displayed only
when the
component (dhw storage tank,
puer or instant heat exchanger)
has been activated
on the board by the after-sales
service.
From the factory the puer is
deactivated and the instant heat
exchanger is active.
P5
P5
P3
P3 P5
Press P5 for 2 seconds.
P5
P5
P5
P5
P5
P5
P5
P5
P5
P5
P5
P3
P3 P5
P5
user menu
CRONO BOILER

6
0
ON
PELLET 0
76°C
set temperature
Allows setting the boiler temperature setpoint
CONTROLS PROCEDURE
From the OFF status, press the P5 for 2 seconds.
The stove will show SET TEMPERATURE.
Press P5, SET H2O will be displayed.
Use keys P2 - P3 to set the temperature.
Press P5 to conrm - press P1 to exit.
set regulations
Allows activating/deactivating the CHRONO function and adjusting the pellet feeding percentage.
CONTROLS PROCEDURE
press P5 for 2 seconds, SET TEMPERATURE will appear.
press P3 once, until ADJUSTMENTS SET IS DISPLAYED.
Press P5 to display ENABLE CHRONO ON/OFF.
Press P3 to enable, P2 to disable.
Press P5 to advance and access pellet adjustments in %.
Press P2- P3 to modify.
Press P5 to conrm - press P1 to exit.
CONTROLS PROCEDURE
press P5 for 2 seconds, SET TEMPERATURE will appear.
Press P3 several times, until the status IS DISPLAYED.
Press P5; the rst reference, ST 01, will appear.
Use keys P3 - P2 to consult the various statuses.
Press P1 to exit.
status
The status menu is used to display the status of the inputs and outputs in the board
ENABLE CHRONO
TEMPERATURE SET H2O
P2P3
P5
TEMPERATURE
SET REGULATIONS ENABLE CHRONO
P2P3
P5
PELLETS
P2P3
P5
TEMPERATURE
SET REGULATIONS
STATUS STOVE STATUS
P5
TEMPERATURE
STOVE STATUS
Status 0 = Flue gas temperature
Status 1 = Auger time
Status 2 = Flue gas speed
Status 3 = Timer status
Status 4 = Tank temperature
Status 5 = Flow
Status 6 = Actual power
Status 7 = Inlet air temperature
Status 8 = Cleaning timer
Status 9 = Mechanical pressure switch
Status A = Digital pressure switch
user menu

7
crono
boiler
(Solo con scheda supplementare)
user menu
This menu allows setting: CLOCK, CHRONO, LANGUAGE, AND BOILER CHRONO.
CONTROLS PROCEDURE
press P5 for 2 seconds, SET TEMPERATURE will appear.
press P3 until USER MENU IS DISPLAYED.
Press P5 to display SET CLOCK.
Press P3 to browse through the menu.
Use buttons P2 e P3 to modify or set.
Press P5 to conrm and access the selected menu.
Press P5 to conrm - press P1 to exit.
USER MENU
P3
TEMPERATURE
USER MENU
SET
CLOCK
DAY MON...SUN Setting the day of the week
HOURS 00...24 Adjustment of the hour
MINUTES 00...59 Adjustment of the minutes
DATE 1...31 Adjustment of the date
MONTH 1...12 Adjustment of the month
YEAR 00...99 Adjustment of the year
SET CHRONO
ENABLE CHRONO OFF Activation/deactivation of the weekly programmer
START  PRG1 OFF  00:00 Time 1st ignition
STOP  PRG1 OFF  00:00 Time 1st switch-o
MONDAY PRG1 OFF ...SUNDAY PRG1 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG1 65  80°C Temperature setting for the 1st time span
START  PRG2 00:10 OFF  00:00 Time 2st ignition
STOP  PRG2 00:10 OFF  00:00 Time 2st switch-o
MONDAY PRG2 OFF ...SUNDAY PRG2 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG2 65  80°C Setting room temperature for the 2st time span
START  PRG3 00:10 OFF  00:00 Time 3st ignition
STOP  PRG3 00:10 OFF  00:00 Time 3st switch-o
MONDAY PRG3 OFF ...SUNDAY PRG3 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG3 65  80°C Setting room temperature for the 3st time span
START  PRG4 00:10 OFF  00:00 Time 4st ignition
STOP  PRG4 00:10 OFF  00:00 Time 4st switch-o
MONDAY PRG4 OFF ...SUNDAY PRG4 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG4 65  80°C Setting room temperature for the 4st time span
LANGUAGE ITAL  ENGL  DEUT  FRAN  ESPA Selecting the language
P5
P5
P5
user menu
crono
boiler
(Only with additional card)
P5

8
FUNCTION
GENERAL DATA
Allows setting a series of general
parameters.
Refer to the corresponding data table.
FACTORY
SETTINGS
Allows conguring a series of factory
settings.
Refer to the corresponding data table.
CLEANING
PARAMETERS
Conguration table of a series of cleaning
parameters.
Refer to the corresponding data table.
WATER
PARAMETERS
Allows setting a series of water parameters.
Refer to the corresponding data table.
CHIMNEY TYPE
Key“77" allows setting the
intake ow for the various debimeter
operating phases.
CONTROLS ACTIVE
Allows activating or deactivating a series of
components, such as
ue gas motor encoder, debimeter, ign-
plug, serial interface.
INSTALLER
Allows modifying a series of
factory settings.
The possible settings refer to pellet feed,
ue motor and ow all in %.
PROGRAMMING STRUCTURE
TECHNIC SET
CODE A0
TECHNICIAN PROGRAMMING
SAVE  EXIT MENU
MODIFY SETTING DATA: INCREASE P3; DECREASE P2
BROWSING PARAMETERS: NEXT P5 ; PREVIOUS P4
FUNCTION
OUTPUTS TESTS
Allows testing the board outputs: Flue
motor and exchanger fans; the voltage
can also be set. As for the auger, the test
activation time can be set. As for the ign-
plug, it can be turned on and o.
COUNTERS
Displays in sequence the consumption
hours for the various brands
(auger operating hours), overall operating
hours.
partial hours, number of start-ups and the
last 5 alarms occurred.
ALARM
MEMORIES
Keys P2 and P3 allow displaying the overall
operating hours,
partial hours, number of start-ups and the
last 5 alarms occurred.
DEFAULT
Key“o1”
("letter o" ) allows reloading factory
settings.
RESET PART
HOURS
Key“77” allows resetting partial operating
hours.
AIR
DISCHARGE
Key“77” allows activating the air discharge
function.
UNLOCK
Key“77” allows skipping all verications for
60 seconds and restarting the stove even
with high ue gas temperature, unreset
timers, etc.
ALARM MEMORY
RESET
Key“77” allows deleting the last alarms
occurred from the memory.
INSTALLER PARAMETERS FUNCTIONS
INSTALLER
P5
P3
P5 P5
P1
P2 P3
P4 P5

9
TECHNICIAN PROGRAMMING
CONTROLS PROCEDURE
Pressing key P5, the words SET TEMPERATURE will be displayed.
press the P3 several times, until the TECHNICIAN MENU is displayed.
Press key P5.
Hold key P3 down to reach the reserved code "A0".
When the code has been reached, conrm by pressing P5.
"INSTALLER  PARAM" will appear.
Press key P5 to conrm.
"GENERAL DATA" will appear.
Enter by pressing key P5.
To modify a single parameter, press P2 or P3.
To proceed and store in the memory, press P5.
To return to the previous parameters, press P4.
Press P1 to return to the previous menus to the initial status.
GENERAL DATA
FIRMWARE VXX
PG00 20
PG01 0,45
PG02 0,45
PG03 P1 0,45
PG04 P5 1,95
PG05 ON 1700
PG06 1600
PG07 P1 900
PG08 P5 1900
PG09 32
FACTORY SETTINGS
CONTROLS PROCEDURE
Pressing key P5, the words SET TEMPERATURE will be displayed.
press the P3 several times, until the TECHNICIAN MENU is displayed.
Press key P5.
Hold key P3 down to reach the reserved code "A0".
When the code has been reached, conrm by pressing P5.
"INSTALLER  PARAM" will appear.
Press key P5 to conrm.
"GENERAL DATA" will appear.
Press P3 to display "FACTORY SETTINGS".
Enter by pressing key P5.
To modify a single parameter, press P2 or P3.
To proceed and store in the memory, press P5.
To return to the previous parameters, press P4.
Press P1 to return to the previous menus to the initial status.
FACTORY settings
FIRMWARE VXX
PF00 10
PF01 18
PF02 7
PF03 ON 110
PF04 170
PF05 OFF
PF06 45
PF07 50
PF08 40
PF09 30
PF10 1
PF11 4
PF12 60
PF13 OFF
PF14 OFF
PF15 1900
PF16 1900
PF17 1900
PF18 60
PF19 0
PF20 1700
PF21 20
PF22 4
GENERAL DATA
P2P3
P5
TECHNIC SET
CODE A0
INSTALLER PARAMETERS
P5
GENERAL DATA
P2P3
P5
TECHNIC SET
CODE A0
INSTALLER PARAMETERS
P5
FACTORY SETTINGS
P2P3
P3
FACTORY settings
FIRMWARE VXX
PF00 10
PF01 18
PF02 7
PF03 ON 110
PF04 170
PF05 OFF
PF06 45
PF07 50
PF08 40
PF09 30
PF10 1
PF11 4
PF12 60
PF13 OFF
PF14 OFF
PF15 1900
PF16 1900
PF17 1900
PF18 60
PF19 0
PF20 1700
PF21 20
PF22 4
GENERAL DATA
INSTALLER PARAMETERS

10
CLEANING PARAMETERS
CONTROLS PROCEDURE
Pressing key P5, the words SET TEMPERATURE will be displayed.
press the P3 several times, until the TECHNICIAN MENU is displayed.
Press key P5.
Hold key P3 down to reach the reserved code "A0".
When the code has been reached, conrm by pressing P5.
"INSTALLER  PARAM" will appear.
Press key P5 to conrm.
"GENERAL DATA" will appear.
Press P3 twice to display "PAR-CLEANING".
Enter by pressing key P5.
To modify a single parameter, press P2 or P3.
To proceed and store in the memory, press P5.
To return to the previous parameters, press P4.
Press P1 to return to the previous menus to the initial status.
WATER PARAMETERS
CONTROLS PROCEDURE
Pressing key P5, the words SET TEMPERATURE will be displayed.
press the P3 several times, until the TECHNICIAN MENU is displayed.
Press key P5.
Hold key P3 down to reach the reserved code "A0".
When the code has been reached, conrm by pressing P5.
"INSTALLER  PARAM" will appear.
Press key P5 to conrm.
"GENERAL DATA" will appear.
Press P3 twice to display "WATER PARAMETERS".
Enter by pressing key P5.
To modify a single parameter, press P2 or P3.
To proceed and store in the memory, press P5.
To return to the previous parameters, press P4.
Press P1 to return to the previous menus to the initial status.
TECHNICIAN PROGRAMMING
CLEANING PARAMETERS
FIRMWARE VXX
PP00 90
PP01 30
PP02 1,65
PP03 2100
PP04 2
PP05 60
PP06 0
PP07 5
PP08 4
PP09 100
PP10 30
PP11 0,85
PP12 1700
PP13 60
PP14 6
WATER PARAMETERS
FIRMWARE VXX
PP00 80
PP01 5
PP02 3
PP03 5
PP04 100
PP05 85
PP06 60
PP07 3
PP08 30
PP09 120
PP10 OFF
PP11 ON
PP12 OFF
PP13 OFF
PP14 2
PP15 05
PP16 05
PP17 90
PP18 170
PP19 OFF
P5
TECHNIC SET
CODE A0
INSTALLER PARAMETERS
P5
GENERAL DATA
P2P3
WATER PARAMETERS
P2P3
P3
GENERAL DATA
P2P3
P5
TECHNIC SET
CODE A0
INSTALLER PARAMETERS
P5
CLEANING PARAMETERS
P2P3
P3