Extron electronics USP 507 User manual

The Extron® Annotator and
USP 507 have a series of
optional output boards.
These boards are:
• Scan converter board • HD-SDI board • DVI-D board
• Scaler board (with DVI-I). Any one of these boards
mounts in the optional output slot, above the RGB and
MTP ports, at the rear of the Annotator or USP 507.
For full device operating details, refer to either the
Annotator User Guide or the USP 507 User Guide, both
available at www.extron.com.
Annotator and USP 507
Optional Output Boards • Installation Guide
Continued on side 2. 1
HDSDI
OUT
DVI-D
OUT
LO-
RES
OUT
R-Y/
R
C
Y/
G
VID
B-Y/
B
Y
SCALED
DVI-I
OUT
Installing a Board in the Annotator or USP 507
1. Turn off the unit, and remove the power cord. Repeat for all connected
devices.
2. Remove eight cover-securing screws from the top and three from each side.
Slide the top cover off. Retain the fourteen screws.
3. At the rear optional output slot either:
a. Remove the two securing screws a from either side of the blank plate
and lift the plate away. Retain the screws.
NOTE: Re-use the screws to
secure the new output
board in place. Retain
the blank plate.
Or,
b. If a board is already installed in the output slot, remove any cables and
the two screws a. Then remove the retaining screw that secures it to the
post on the device motherboard. Carefully lift the board away from the
socket. Retain all the screws.
4. Remove the new board from its box and anti-ESD bag,
holding the board by the front frame or board edge.
5. Turn the board over so the header sockets face up. Insert
the supplied connector pins into the sockets on the board.
6. Turn the board over again so the connector pins are now
facing down. Carefully align the pins with the appropriate sockets on the
unit motherboard, and push the board firmly down into the sockets.
7. Secure the board to the frame with the two retaining screws a and to the
post on the motherboard using either the original or the supplied screw.
8. Replace the cover, securing it with the fourteen screws removed in step 2.
9. Reconnect any input and output devices and connect to the new board.
10. Connect any control devices.
11. Power on the Annotator or USP 507, and all the connected devices.
Header Socket
RGB/R-Y,Y,B-Y MTP
LO-
RES
OUT R-Y/
R
C
Y/
G
VID
B-Y/
B
Y
1 1

Extron USA - West
Headquarters
+800.63 3.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.63 3.9876
Inside USA / Canada Only
+1.919.8 63.1794
+1.919.8 63.1797 FA X
Extron Europe
+800.39 87.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.638 3.44 00
+65.638 3.46 64 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FA X
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX [phone]
Rev B
09 10
© 2010 Extron Electronics. All rights reserved. www.extron.com
2
Annotator and USP 507
Optional Output Board • Installation Guide, (continued)
Configuring the Boards Using the Front Panel Menu System
To configure the HD-SDI and DVI-D boards using the front panel menu system,
refer to the relevant device user guide, available at www.extron.com.
The Annotator and the USP 507 have a separate front panel menu for configuring
either the scan converter board or the scaler DVI-I board. This menu is accessible
only after the board has been installed.
Scan Converter Board and Scaler DVI-I Board Configuration Menus
1. Press the Menu button repeatedly until
either the Scan Converter Settings menu
or the Aux Scaler Configuration menu
appears, as applicable.
2. Press the Next button to reach each
submenu as desired (see the images at
right) and use the front panel adjustment
knobs ([ {) to change the settings.
Configuring the Boards Using the Signal
Processing Products Control Program
1. Open the Signal Processing Products
Control Program (SPPCP) on a PC that is
connected to the Annotator or USP 507
via a LAN or an RS-232 port.
2. Connect to the device. A new board
relevant tab (Scan Converter or AUX
Scaler) is now available. Click on the
desired tab to configure the settings.
NOTE: HD-SDI and DVI-D output
boards are buffered, so
resolution and refresh rates
match all other outputs.
Refer to the SPPCP Help File for details.
Configuring the Boards Using Internal Web Pages
1. Using a LAN connection, open an Internet browser, enter the IP address of
the unit in the browser address bar, and connect to the unit.
2. Click on the Configuration tab and configure the settings as needed.
Refer to the Annotator or USP 507 User Guide at www.extron.com for details.
Configuring the Boards Using SIS™ Commands
The boards can also be configured with specific SIS commands. Refer to the
Annotator or USP 507 User Guide at www.extron.com for SIS command listings.
H Size V
2048 2048
Scan Converter
Settings
Rotate to adjust
H value. Rotate
to adjust V value.
Output Format
S-video/Comp
Output Standard
NTSC
Next
Next
Next
Next
Flicker Filter
3
Next
H Center V
2048 2048
Rotate to adjust
H value. Rotate
to adjust V value.
Rotate either to
select output format.
Rotate either to
select output
standard.
H Filter
0
Next
Encoder Filter
0
Next
Rotate either to
adjust encoder filter.
Rotate either to
adjust flicker filter.
Rotate either to
adjust H filter.
Resol 1024x768
Refresh 60.00Hz
Aux Scaler
Configuration
Rotate to adjust
resolution. Rotate
to adjust refresh rate.
Aspect Ratio
Follow
Next
Next
Next
Detail
64
Next
Sync Polarity
H neg V neg
Rotate either to
select aspect
ratio mode.
Test Pattern
Crop
Next
Rotate either to
adjust detail level.
Rotate either to
select test pattern.
Output Type
RGBHV
Next
Rotate either to
select output type.
Rotate either to
adjust sync polarity
values.