Unitronics UID-W1616R User manual

Unitronics
1
Uni-I/O™ Wide
Modules
User Guide
UID-W1616R, UID-W1616T
Uni-I/O™ Wide is a family of Input/Output modules that are compatible with the
UniStream™ control platform. Wide Modules are 1.5 times as wide as Uni-I/O™ modules,
and comprise more I/O points in less space.
This guide provides basic installation information for UID-W1616R and UID-W1616T Uni-
I/O™ modules.
Technical specifications may be downloaded from the Unitronics website.
The UniStream™ platform
comprises CPU controllers, HMI
panels, and local I/O modules
that snap together to form an
all-in-one Programmable Logic
Controller (PLC).
Install Uni-I/O™ modules:
▪Onto the back of any
UniStream™ HMI Panel
comprising a CPU-for-Panel.
▪Onto a DIN-rail, using a
Local Expansion Kit.
The maximum number of Uni-I/O™ Wide modules that can be connected to a single CPU
controller is limited. For details, please refer to the specification sheets of the
UniStream™ CPU or any of the relevant Local Expansion Kits.
Before You Begin
Before installing the device, the installer must:
▪Read and understand this document.
▪Verify the Kit Contents.
Installation option requirements
If you are installing a Uni-I/O™ module onto:
▪A UniStream™ HMI Panel; the Panel must comprise a CPU-for-Panel, installed according
to the CPU-for-Panel installation guide.
▪A DIN-rail; you must use a Local Expansion Kit, available by separate order, to integrate
the Uni-I/O™ modules on the DIN-rail into a UniStream™ control system.
Alert Symbols and General Restrictions
When any of the following symbols appear, read the associated information carefully.
Symbol
Meaning
Description
Danger
The identified danger causes physical and property damage.
Warning
The identified danger could cause physical and property damage.
Caution
Caution
Use caution.
▪All examples and diagrams are intended to aid understanding, and do not guarantee
operation. Unitronics accepts no responsibility for actual use of this product based on
these examples.

UID-W1616R, UID-W1616T Installation Guide
2
Unitronics
▪Please dispose of this product according to local and national standards and regulations.
▪This product should be installed only by qualified personnel.
▪Failure to comply with appropriate safety guidelines can cause severe injury or
property damage.
▪Do not attempt to use this device with parameters that exceed permissible levels.
▪Do not connect/disconnect the device when power is on.
Environmental Considerations
▪Ventilation: 10mm (0.4”) of space is required between the device top/bottom edges
and the enclosure’s walls.
▪Do not install in areas with: excessive or conductive dust, corrosive or flammable
gas, moisture or rain, excessive heat, regular impact shocks or excessive vibration,
in accordance with the standards and limitations given in the product’s technical
specification sheet.
▪Do not place in water or let water leak onto the unit.
▪Do not allow debris to fall inside the unit during installation.
▪Install at maximum distance from high-voltage cables and power equipment.
Kit Contents
▪1 Uni-I/O™ module
▪4 I/O terminal blocks (2 black and 2 gray)
Uni-I/O™ Diagram
1
DIN-rail clips
Provide physical support for CPU and modules. There are two
clips: one at the top (shown), one at the bottom (not shown).
2
I/Os
I/O connection points
3
4
I/O Bus - Left
Left-side Connector
5
Bus Connector
Lock
Slide the Bus Connector Lock to the left, to electrically connect
the Uni-I/O™ module to the CPU or adjacent module.
6
I/O Bus - Right
Right-Side Connector, shipped covered. Leave covered when not
in use.
Bus Connector
Cover
7
I/Os
I/O connection points
8

UG_UID-W1616T_R
Unitronics
3
9
I/O LEDs
Green LEDs
10
11
Status LED
Tricolor LED, Green/Red/Orange
NOTE
▪Refer to the module's specification sheet for LED indications.
12
Module door
Shipped covered with protective tape to prevent the door from
being scratched. Remove tape during installation.
13
Screw holes
Enable panel-mounting; hole diameter: 4mm (0.15”).
About the I/O Bus Connectors
The I/O Bus connectors provide the physical and electrical connection points between
modules. The connector is shipped covered by a protective cover, protecting the connector
from debris, damage, and ESD.
The I/O Bus - Left (#4 in diagram) can be connected to either a CPU-for-Panel, a
Uni-COM™ Communication module, to another Uni-I/O™ module or to the End Unit of a
Local Expansion Kit.
The I/O Bus - Right (#6 in diagram) can be connected to another I/O module, or to the
Base Unit of the Local Expansion Kit.
Caution
▪If the I/O module is located last in the configuration, and nothing is to be
connected to it, do not remove its Bus Connector Cover.
Installation
▪Turn off system power before connecting or disconnecting any modules or devices.
▪Use proper precautions to prevent Electro-Static Discharge (ESD).
Installing a Uni-I/O™ Module onto a UniStream™ HMI Panel
NOTE
The DIN-rail type structure on the back of the panel provides the physical support for
the Uni-I/O™ module.
1. Check the unit to which you will connect the Uni-I/O™ module to verify that its Bus
Connector is not covered.
If the Uni-I/O™ module is to be the last one in the configuration, do not remove the
cover of its I/O Bus Connector - Right.
2. Open the door of the Uni-
I/O™ module and hold it as
shown in the accompanying
figure.
3. Use the upper and lower
guide-tunnels (tongue &
groove) to slide the Uni-
I/O™ module into place.
4. Verify that the DIN-rail clips
located at the top and
bottom of the Uni-I/O™
module have snapped onto
the DIN-rail.

UID-W1616R, UID-W1616T Installation Guide
4
Unitronics
5. Slide the Bus Connector Lock all the way to
the left as shown in the accompanying figure.
6. If there is already a module located to its
right, complete the connection by sliding the
Bus Connector lock of the adjacent unit to the
left.
7. If the module is the last in the configuration,
leave the I/O bus connector covered.
Removing a Module
1. Turn off the system power.
2. Disconnect the I/O terminals (#2,3,7,8 in the diagram).
3. Disconnect the Uni-I/O™ module from the adjacent units: slide its Bus Connector Lock
to the right. If there is a unit located on its right, slide the lock of this module to the
right as well.
4. On the Uni-I/O™ module, pull the top DIN-rail clip up and the bottom clip down.
5. Open the door of the Uni-I/O™ module and hold it with two fingers as shown in the
figure on page 3; then pull it carefully from its place.
Installing Uni-I/O™ modules onto a DIN-rail
To mount modules onto a DIN-rail, follow steps 1-7 in Installing a Uni-I/O™ Module onto a
UniStream™ HMI Panel on page 3.
In order to connect the modules to a UniStream™ controller, you must use a Local
Expansion Kit.
These kits are available with and without power supplies, and with cables of varying
lengths. For complete information, please refer to the installation guide of the relevant
Local Expansion Kit.
Numbering Modules
You can number modules for reference purposes. A set of 20 stickers is provided with
every CPU-for-Panel; use these stickers to number the modules.
▪The set contains numbered and blank
stickers as shown in the figure to the left.
▪Place them on the modules as shown in the
figure to the right.
UL Compliance
The following section is relevant to Unitronics’ products that are listed with the UL.
The following models: UID-W1616R is UL listed for Hazardous Locations.
The following models: UID-W1616R, UID-W1616T are UL listed for Ordinary Location.

UG_UID-W1616T_R
Unitronics
5
UL Ratings, Programmable Controllers for Use in Hazardous Locations,
Class I, Division 2, Groups A, B, C and D
These Release Notes relate to all Unitronics products that bear the UL symbols used to
mark products that have been approved for use in hazardous locations, Class I, Division 2,
Groups A, B, C and D.
Caution
▪This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D,
or Non-hazardous locations only.
▪Input and output wiring must be in accordance with Class I, Division 2 wiring
methods and in accordance with the authority having jurisdiction.
▪WARNING—Explosion Hazard—substitution of components may impair
suitability for Class I, Division 2.
▪WARNING –EXPLOSION HAZARD –Do not connect or disconnect equipment
unless power has been switched off or the area is known to be non-
hazardous.
▪WARNING –Exposure to some chemicals may degrade the sealing properties
of material used in Relays.
▪This equipment must be installed using wiring methods as required for Class
I, Division 2 as per the NEC and/or CEC.
Certification UL des automates programmables, pour une utilisation en
environnement à risques, Class I, Division 2, Groups A, B, C et D.
Cette note fait référence à tous les produits Unitronics portant le symbole UL - produits qui
ont été certifiés pour une utilisation dans des endroits dangereux, Classe I, Division 2,
Groupes A, B, C et D.
Attention
▪Cet équipement est adapté pour une utilisation en Classe I, Division 2,
Groupes A, B, C et D, ou dans Non-dangereux endroits
seulement.
▪Le câblage des entrées/sorties doit être en accord avec les méthodes
de câblage selon la Classe I, Division 2 et en accord avec l’autorité compétente.
▪AVERTISSEMENT: Risque d’Explosion – Le remplacement de certains composants
rend caduque la certification du produit selon la Classe I, Division 2.
▪AVERTISSEMENT - DANGER D'EXPLOSION - Ne connecter pas ou ne débranche
pas l'équipement sans avoir préalablement coupé l'alimentation électrique ou la
zone est reconnue pour être non dangereuse.
▪AVERTISSEMENT - L'exposition à certains produits chimiques peut dégrader les
propriétés des matériaux utilisés pour l'étanchéité dans les relais.
▪Cet équipement doit être installé utilisant des méthodes de câblage suivant la
norme Class I, Division 2 NEC et /ou CEC.
Wiring
▪This equipment is designed to operate only at SELV/PELV/Class 2/Limited Power
environments.
▪All power supplies in the system must include double insulation. Power supply
outputs must be rated as SELV/PELV/Class 2/Limited Power.

UID-W1616R, UID-W1616T Installation Guide
6
Unitronics
▪Do not connect either the ‘Neutral’ or ‘Line’ signal of the 110/220VAC to device’s 0V
point.
▪Do not touch live wires.
▪All wiring activities should be performed while power is OFF.
▪Use over-current protection, such as a fuse or circuit breaker, to avoid excessive
currents into the Uni-I/O™ module supply port.
▪Unused points should not be connected (unless otherwise specified). Ignoring this
directive may damage the device.
▪Double-check all wiring before turning on the power supply.
Caution
▪To avoid damaging the wire, use a maximum torque of 0.5 N·m (5 kgf·cm).
▪Do not use tin, solder, or any substance on stripped wire that might cause the
wire strand to break.
▪Install at maximum distance from high-voltage cables and power equipment.
Wiring Procedure
Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm2–3.31 mm2).
1. Strip the wire to a length of 7±0.5mm (0.250–0.300 inches).
2. Unscrew the terminal to its widest position before inserting a wire.
3. Insert the wire completely into the terminal to ensure a proper connection.
4. Tighten enough to keep the wire from pulling free.
Uni-I/O™ Module Connection Points
All wiring diagrams and instructions in this document refer to the I/O connection points of
the different modules. These are arranged in four groups of eleven points each, as shown
in the figures below.
UID-W1616R
UID-W1616T

UG_UID-W1616T_R
Unitronics
7
Wiring Guidelines
In order to ensure that the device will operate properly and to avoid electromagnetic
interference:
▪Use a metal cabinet. Make sure the cabinet and its doors are properly earthed.
▪Use wires that are properly sized for the load.
▪Route each I/O signal with its own dedicated common wire. Connect common wires at
their respective common (CM) points at the I/O module.
▪Individually connect each 0V point in the system to the power supply 0V terminal.
▪Individually connect each functional earth point ( ) to the earth of the system
(preferably to the metal cabinet chassis). Use the shortest and thickest wires possible:
less than 1m (3.3’) in length, minimum thickness 14 AWG (2 mm2).
▪Connect the power supply 0V to the earth of the system.
NOTE
For detailed information, refer to the document System Wiring Guidelines, located in
the Technical Library in the Unitronics’ website.
Wiring the Inputs: UID-W1616R, UID-W1616T
UID-W1616R
UID-W1616T
The inputs are arranged in two isolated groups:
▪I0-I7 share common CM0
▪I8-I15 share common CM1
Each input group may be wired as sink or source. Wire each group according
to the figures below.
Input wiring, sink
Input wiring, source
NOTE
▪Use sink input wiring to connect a sourcing (pnp) device.
▪Use source input wiring to connect a sinking (npn) device.

UID-W1616R, UID-W1616T Installation Guide
8
Unitronics
Wiring Relay Outputs: UID-W1616R
Output's power supply
The relay outputs require an external 24VDC power supply. Connect the 24V and 0V
terminals as shown in the figure below.
▪To avoid risk of fire or property damage, always use a limited current source or
connect a current limiting device in series with the relay contacts.
▪The 0V of the module must be connected to the HMI Panel’s 0V.
Ignoring this directive may damage the device.
▪In the event of voltage fluctuations or non-conformity to voltage power supply
specifications, connect the module to a regulated power supply.
UID-W1616R
The outputs are arranged in two
isolated groups:
▪O0-O7 share common CM2
▪O8-O15 share common CM3
Wire each group according to the accompanying figure.
Increasing contact life span
To increase the life span of the relay contacts and protect the module from potential
damage by reverse EMF, connect:
▪a clamping diode in parallel with each inductive DC load.
▪an RC snubber circuit in parallel with each inductive AC load.
DC Load
AC Load

UG_UID-W1616T_R
Unitronics
9
Wiring Transistor Outputs: UID-W1616T
Output’s power supply
The use of any of the outputs requires an
external 24VDC power supply as shown in the
accompanying figure.
▪In the event of voltage fluctuations or non-conformity to voltage power supply
specifications, connect the device to a regulated power supply.
Outputs
Connect the 24V and 0V terminals as shown
in the accompanying figure.
UID-W1616T
O0-O15 share common
return 0V
Technical Specifications
Part no.
UID-W1616R
UID-W1616T
Inputs
16
16
Type
Sink or Source , 24VDC
Sink or Source , 24VDC
Outputs
16
16
Type
Relay, 24VDC (power supply)
Transistor, Source (pnp), 24VDC
Isolation
All inputs and outputs are isolated
Inputs
UID-W1616R
UID-W1616T
Number of inputs
16
16
Type
Sink or Source
Isolation groups
Two groups of 8 inputs each
Isolation voltage
Group to bus
500VAC for 1 minute
Group to group
500VAC for 1 minute
Input to input
within group
None
Nominal voltage
24VDC @ 6mA
Input voltage
Sink/Source
On state: 15-30VDC, 4mA minimum
Off state: 0-5VDC, 1mA maximum
Nominal impedance
4kΩ
Filter
Settable between 1 to 32 ms (individually per group)

UID-W1616R, UID-W1616T Installation Guide
10
Unitronics
Outputs
UID-W1616R
UID-W1616T
Number of outputs
16
16
Output type
Relay, SPST-NO (Form A)
Transistor, Source
Isolation groups
Two groups of 8 outputs each
One group of 16 outputs
Isolation voltage
Group to bus
1,500VAC for 1 minute
500VAC for 1 minute
Group to group
1,500VAC for 1 minute
-
Output to output
within group
None
None
Output power supply
to bus
None
500VAC for 1 minute
Output power supply
to output
1,500VAC for 1 minute
None
Current
2A maximum per output
8A maximum per group
(Resistive load)
0.5A maximum per output.
Voltage
250VAC / 30VDC maximum
See Outputs Power Supply
specfication
Minimum load
1mA, 5VDC
-
ON state voltage drop
-
0.5V maximum
OFF state leakage
current
-
10µA maximum
Switching times
10ms maximum
Turn-on/off: 80s max.
(Load resistance < 4kΩ (
Short-circuit protection
None
Yes
Life expectancy (6)
100k operations at maximum
load
-
Outputs Power Supply
UID-W1616R
UID-W1616T
Nominal operating voltage
24VDC
Operating voltage
20.4 –28.8VDC
Maximum current
consumption
80mA@24VDC
60mA@24VDC(7)
IO/COM Bus
UID-W1616R
UID-W1616T
Bus maximum current
consumption
100mA
120mA

UG_UID-W1616T_R
Unitronics
11
LED Indications
Input LEDs
Green
Input state
Output LEDs
Green
Output state
Status LED
A triple color LED. Indications are as follows:
Color
LED State
Status
Green
On
Operating normally
Slow blink
Boot
Rapid blink
OS initialization
Green/Red
Slow blink
Configuration mismatch
Red
Slow blink
No IO exchange
Rapid blink
Communication error
Orange
Rapid blink
OS Upgrade
Environmental
Protection
IP20, NEMA1
Operating temperature
-20°C to 55°C (-4°F to 131°F)
Storage temperature
-30°C to 70°C (-22°F to 158°F)
Relative Humidity (RH)
5% to 95% (non-condensing)
Operating Altitude
2,000m (6,562 ft)
Shock
IEC 60068-2-27, 15G, 11ms duration
Vibration
IEC 60068-2-6, 5Hz to 8.4Hz, 3.5mm constant amplitude,
8.4Hz to 150Hz, 1G acceleration.
Dimensions
UID-W1616R
UID-W1616T
Weight
0.230 kg (0.507 lb)
0.226 kg (0.498 lb)
Size
Identical for all models, as shown in the images below
Top View

UID-W1616R, UID-W1616T Installation Guide
12
Unitronics
Side View
Front View
Notes
6. Life expectancy of the relay contacts depends on the application that they are
used in. The product’s installation guide provides procedures for using the
contacts with long cables or with inductive loads.
7. Current consumption does not include load current.
The information in this documentreflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole discretion, and without notice, to
discontinue or change the features, designs, materials and otherspecifications of its products, and to either permanently or temporarily withdraw anyof the forgoing from the market.
All information in this document is provided "as is" withoutwarranty of any kind, either expressed or implied, including but not limited to any implied warranties of merchantability, fitness for
a particular purpose, or non-infringement.Unitronics assumes no responsibility for errors or omissions in the information presented in this document. In no event shallUnitronics be liable
for any special, incidental, indirect or consequential damages of any kind,or anydamages whatsoever arising outof or in connection with theuse or performance of this information.
The tradenames, trademarks,logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other third parties and you are
not permitted to use them without the prior written consent of Unitronics or such third party as may own them
UG_UID-W1616T_R.pdf 09/22