Extron electronics 70-151-01 User manual

User’s Guide
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax [phone]
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax [phone]
www.extron.com
© 2002 Extron Electronics. All rights reserved.
70-151-01 Upgrade Kit
68-618-01 Rev. B
Printed in the USA
08 02
DVS 406 Audio I/O Card
4. Insert the card’s installation screws through the audio card’s
four mounting holes and gently tighten them into the
standoffs.
Fig. 4 — Audio I/O card mounted in place
5. Replace the top cover on the DVS 406 scaler, and fasten it
with the screws which were removed in step 3 of the
“Internal access” section.
6. Rack/furniture mount the scaler, and reconnect the AC
power cord.
Part Numbers
Extron Part Part Number
Audio I/O Card Kit 70-151-01
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

DVS 406 Audio I/O Card • InstallationDVS 406 Audio I/O Card • Installation
Installation
32
Installing the Audio I/O Card
The audio I/O card is installed in the DVS 406 by following the
instructions and illustrations shown below.
Internal access
To gain access to the internal components, do the following:
1. Remove the power cable from the DVS 406 and from the
power source.
Do not open the cover of the scaler without
unplugging the power cord.
2. If the DVS 406 scaler is rack mounted, remove the input and
output cables from it and remove the unit from the rack. If
the scaler is not rack mounted, you do not need to remove
the input and output cables.
3. Remove 13 screws from the top and sides of the cover
(figure 1).
Fig. 1 — Removing the cover
4. Remove the cover by slightly lifting each side alternately
until the cover is free.
Reverse this procedure to reinstall the cover after the audio card
has been installed.
CAUTION
Do not touch any switches or other electronic
components inside the scaler. Doing so could damage
the scaler. Electrostatic discharge (ESD) can damage
IC chips even though you cannot feel it. You must be
electrically grounded. A grounding wrist strap is
recommended.
Card installation
After following the instructions in “Internal access” to remove
the cover, do the following:
1. Locate the four audio card standoffs located at the left rear
portion of the main circuit board (looking from above with
the front panel nearest to you).
Fig. 2 — Audio card standoffs
2. Remove the adhesive audio connector cover from the rear
audio connector opening of the scaler and position the audio
card at an angle with the audio connector protruding
through the rear audio connector opening.
3. The audio card has a 20-pin socket on the underside that
must align with the 20 pins on the main circuit board. Be
sure to align the pins properly, in order to prevent bending
the pins, before pressing the audio card firmly in place
against the standoffs. The four mounting holes on the audio
card should now be directly over the standoffs.
Fig. 3 — Audio card positioned above pins and
standoffs
NEXT
MENU
PICTUREADJUSTMENTS
DIGITALVIDEOSCALER
4
2
1356
VIDEO/
S-VIDEO
RGB/YUV
RGBVIDEO/
S-VIDEOVIDEO/
S-VIDEOSDITAKE
COL/TNT BRT/CONT DETAIL SIZE CENTER
DVS406
ADJUST
Lift Cover
Straight Up
Remove (13)
screws from
top and sides
Audio card
standoffs
20-pin socket on
back of audio card
20-pin connector
on main board
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]