Extron electronics SMK V SB 33 User manual

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
SMK V SB 33 82-100 VESA Mounting Kit
Setup Guide
Product Description
The SMK V SB 33 82-100 VESA Mounting Kit allows the SB 33 A 82-90 and SB 33 A 90-100 soundbar speakers to be attached
to the same VESA display mount that supports the display device. This type of installation enables the SB 33 speaker to be
aligned with the display for a visually aesthetic installation. The SB 33 front speaker surface can be adjusted ush with the front of
the display. It can be adjusted forward, backward, up, down, and side-to-side.
Installation
VESA display mounts come in a variety of different styles, so these instructions for installing the SMK V SB 33 82-100 VESA
Mounting Kit are variable. Consult the installation guides for your VESA display mount and your display device before installing
the kit. Follow the steps below to install the kit.
WARNING: The final installation should be able to continuously support the speaker weight. The final installation
should also be able to support short term overloading. Be sure to not exceed the load limit of the VESA mount, mounting
surface, and SMK V SB 33 82-100. The maximum load limit of the SMK V SB 33 82-100 is 85 lb. (38 kg) Since applications
can vary considerably, it is assumed that the installer will exercise good judgment when selecting the mounting location,
method, and hardware. Installation and service must be performed by authorized personnel only.
AVERTISSEMENT : L’installation nale doit pouvoir supporter en permanence le poids de l’enceinte. L’installation nale
doit également pouvoir supporter une courte surcharge. Veillez à ne pas dépasser la charge maximale du support de
montage VESA, de la surface de montage, et de l’unité SMK V SB 33 82-100. La charge maximale du SMK V SB 33 82-
100 est de 38 kg. Étant donné la possibilité d’évolution considérable des applications, il est supposé que l’installateur fera
preuve de discernement lors de la sélection de l’emplacement, du mode, et du matériel de montage. L’installation et la
maintenance du système doivent être exclusivement effectuées par un technicien agréé.
NOTE: Observe all applicable building codes and local ordinances when installing the SB 33 A speaker.
The SMK V SB 33 82-100 VESA Mounting Kit is composed of 2 long L-brackets, 2 short L-brackets, reinforcing plate (see
figure4 on page3), 4 plastic spacers, 10 bolts, 10 lock washers, 10 washers, and 10 wingnuts.
1. Install the wall mount portion of the VESA display mount onto the desired wall location (see the VESA display mount
installation guide).
2. Position one long L-bracket of the SB 33 kit on the back of the display while aligning the bolt holes on the display with a slot
on the L-bracket. Repeat this procedure for the other long L-bracket on the other side of the display (see figure1).
TOP
DISPLAY
(REAR)
Long L-brackets
Bolt Holes
Figure 1. Installing Long L-brackets
1

2
SMK V SB 33 Kit • Setup Guide (Continued)
3. Place the VESA display mount on top of the L-bracket while aligning the bolt holes of the display mount with the slot of
the L-bracket and the bolt holes of the display. Repeat this procedure for the other long L-bracket on the other side of the
display.
TOP
DISPLAY
(REAR)
Long L-brackets
Mounting Screws
VESA Display
Mount (not included)
Washers
Figure 2. Installing VESA Display Mount
4. Insert bolts through the VESA display mounts, the long L-brackets, and the display, making sure to the align the bolt holes
of the VESA display mounts with the bolt holes of the display (see figure2). Tighten all four bolts. Spacers are provided if
needed.
5. Position the short L-bracket under the long L-bracket that was installed in step 4 above so that the L bends of each bracket
are paired together (see figure3, 1). Then install one bolt with a wingnut and lockwasher (included in the kit) so that the long
L-bracket and short L-bracket are held together. Tighten the wingnut. Repeat this procedure for the other long L-bracket on
the other side of the display.
NOTE: The short L-bracket may be reversed if the SB 33 speaker needs to be positioned further forward relative to the
display above it (2).
TOP
DISPLAY
(REAR)
TOP
DISPLAY
(REAR)
Lock
Washer
Wingnut
Short
L-bracket
Long
L-bracket
Bolt
Alternative Installation of
Short L-bracket
Short
L-bracket
(Reversed)
1
1
1
2
2
2
Figure 3. Installing Short L-brackets on the Long L-brackets
2
3

3
6. For extra stiffening, attach the metal reinforcing plate connection bracket to the back of the SB 33 A 82-90 or SB 33 A 90-100
wall plate.
Left piece of Wallplate
(with level bubble)
Bolt
Wingnut
Lock
Washer
Right piece of Wallplate
(without level bubble)
Reinforcing
Plate
Figure 4. Attaching the Reinforcing Plate
7. Install the SB 33 speaker wallplate to the short L-bracket using two bolts, two lock washers, and two wingnuts, as shown in
figure5. Repeat this procedure for the other short L-bracket on the other side.
TOP
DISPLAY
(REAR)
Lock
Washer Wallplate
Wingnut
Short
L-bracket
Bolt
Long
L-bracket
Figure 5. Installing the SB 33 Speaker Wall Plate
8. Fasten the display onto the VESA wall mount that was attached in step 1 on page 1.
4
5

4
SMK V SB 33 Kit • Setup Guide (Continued)
9. Adjust the SB 33 vertically as needed:
a. Loosen, but do not remove, the bolts that attach the long L-brackets to the display.
TOP
DISPLAY
(REAR)
Vertical Adjustment
Long
L-bracket
Bolt
VESA Display
Mount
Washer
Figure 6. Adjusting the SB 33 Speaker Wall Plate
b. Adjust the SB 33 to the desired distance from the display, then tighten the bolts.
NOTE: Assuming that the display screen is level, allow for some space
between the bottom of the display screen and the top of the speaker,
because the speaker assemblies and the center bracket attach to the
wallplate by hooking the top mounting clasps of the speaker assemblies
and center bracket over the top mounting rail of the wall plate (see the
diagram at right).
To allow sufficient clearance between the top of the SB 33 A and the
display screen above it, leave at least 0.69 inches (17.5 mm) between
the highest part of the top rail of the wallplate and the top of the speaker,
as shown at right. The display screen should not encroach into this area
above the top rail.
10. Install the SB 33 A speaker to the wallplate. If the alignment between the display and the SB 33 speaker needs to be
adjusted, see Aligning the SB 33 Speaker to the Display on page5.
TOP
DISPLAY
(REAR)
DISPLAY
(REAR)
Wallplate
Short
L-bracket
Long
L-bracket
SB 33 A Speaker
Display
Figure 7. Installing the SB 33 Speaker Wallplate
6
INPUTS
POWER
MAX
12V
0.7A
OUTPUT
REMOTE
V
L
LRLEVEL BASS TREBLE
R
CG
10V 50mA
CLASS 2 WIRING
L SPEAKER
Wallplate
Side View
11/16"
(17.46 mm)
Wall
7

5
Aligning the SB 33 Speaker to the Display
The SMK V SB 33 82-100 VESA Mounting Kit can be adjusted to align the SB 33 speaker assembly relative to the front of the
display, from front to rear (depth).
To align the speaker to the display:
1. Loosen, but do not remove, the two wingnuts that attach the long L-brackets to the short L-brackets.
TOP
DISPLAY
(REAR)
Depth Adjustment
Short
L-bracke
t
Long
L-bracket
Figure 8. Adjusting Depth
2. Adjust the SB 33 either to the front or to the rear of the display and then tighten the wingnuts.
See the SB 33 A Series Setup Guide and SB 33 A Series User Guide for further installation details.
8

6
68-3701-50 Rev. A
04 22
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2022 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876