EZBoilers EZ-Pro User manual

Owner’s Manual
EZBoilers
EZ-Classic and EZ-Pro
UL 2523-2009 Solid fuel fired hydronic heating appliances water heaters and boilers
CAN/CSA B366.1-2011 Solid fuel fired central heating appliances.
EZBoilers
Formerly Ridgewood Stoves
1445 170th Ave.
Hersey Michigan 49639
Call or text: [phone]
INTRODUCTION
Thank you for purchasing our stove. Developed and manufactured in Hersey Michigan
the EZBoilers “Simple and Strong” stove has been designed to supply heat and hot
water for your home or business. The strongest structural design is round and the
weakest is square or rectangular. This pertains to stoves as well. For longevity and
strength our stove uses a round heavy-duty design for the firebox. Rectangular designs
with many overlapping welds and faceted corners can be problematic. Our water jacket

is also a round design and is 3/16” thick. Your stove also utilizes a natural draft burning
technology to get all of the energy out of traditional fuel sources and to provide you
with many years of safe and cost-effective heating of your building and domestic hot
water supply. With no major electronics or fans on the outside of the unit our stove is
simple and safer. The majority of the parts we use are off-the-shelf readily available to
make service easy. To ensure that you have a clear understanding of the operating
procedures of your stove please take the time to read this manual thoroughly. If you
have any questions give us a call at [phone]. We will be happy to answer any
questions you have.
Thanks again
The EZBoilers Simple and Strong Stove Team
Simple and Strong…. that’s our Stove.
SAFETY
Do not operate this equipment for anything other than its intended purpose.
Do not install in a home basement or garage. This stove is intended to be used
outdoors.
Caution….Hot Surfaces….Never leave children unattended near the stove.
Do not burn any material other than natural organics. Do not burn GARBAGE
HOUSEHOLD WASTE STRAW HAY or YARD WASTE. Do not use flammable liquids or
materials to start or to enhance the fire. Never use any type of petroleum product
petroleum based product charcoal starter lighter fluid lantern fuel kerosene or any
other flammable accelerant to start your fire.
Start your fire with paper cardboard and small kindling never any type of flammable
liquid.
When opening the firebox door pause between the first (main) latch and the safety
latch. This type of latch is called a Door Anti Blowback Latch. There can be unburned
gases built up inside of the firebox during normal operation. Pausing at the safety latch
will allow those gases to ignite and burn off. Failure to make this a practice could result
in severe burns. Always close the stove door tightly after tending your fire.

Never leave the stove unattended if the firebox door is open or unlatched.
Do not touch any part of the front of your stove that is uninsulated. Temperatures can
reach 200 degrees in these areas. Failure to do this could result in severe burns.
To avoid electrical shock disconnect the electricity before performing maintenance.
Always wear protective gloves and glasses. Be aware that hanging or loose clothing can
catch fire.
Ashes should be placed in a metal container with a tight fitting lid. The closed container
of ashes should be placed on a non-combustible floor or on the ground. All combustible
materials should be disposed of by burial in the soil or otherwise dispersed. They
should be retained in the closed container until all cinders have thoroughly cooled.
Using an outdoor stove helps eliminate the risk of a house fire chimney fire indoor
smoke or carbon monoxide poisoning.
The EZ Boilers Simple and Strong stove has been tested to UL 2523-2009 solid fuel fired
hydronic heating appliances water heaters and boilers CAN/CSA B366.1-2011 Solid
fuel fired central heating appliances.
SECTION 1
INSTALLATION
CAUTION – DO NOT FIRE T IS UNIT UNTIL OPERATING INSTRUCTIONS AVE BEEN
READ AND FULLY UNDERSTOOD. NEVER LIG T A FIRE IN T E STOVE DRY (WIT OUT
WATER), AS T E STOVE WILL BURN UP.
T IS UNIT MUST BE INSTALLED BY A QUALIFIED INSTALLER.
Before installing your stove always check any and all applicable state and local
regulations and consult with your insurance agent.

We recommend installing your stove a distance of at least 5 feet from any structure
and at least 25 feet away from fuel storage tanks such as liquid propane. However
farther away is even better. The underground insulated PEX water lines can transport
heated water for a long distance without sacrificing economy. Safety should be a top
priority. Your stove should be located with consideration to your neighbor’s property.
This type of stove is not designed to be located or operated in densely populated areas.
Stove Footprint. When you’re beginning to install your boiler the footprint comes in
handy to position the blocks under the legs or pouring a concrete pad. EZ-Pro: L = 60
inches W = 44 inches. EZ-Classic: L = 48 inches W = 44 inches
Those measurements are from the outside of the legs which are approximately 3 inches square. Therefore the EZ-Pro
measures 57″ by 41″ on center and the EZ-Classic measures 45″ by 41″ on center.
CAUTION: Lift and move the stove at your own risk. Do not lift your stove from the
bottom with a fork truck or similar equipment. You can safely lift your stove by
removing the chimney diverter clean-out dropping a chain through the chimney into
the firebox and attaching the chain to the door frame. The stove can also be picked up
using a fork truck by putting the forks through the door opening and into the firebox.
Electrical
We recommend that a licensed professional electrician makes all of the necessary
electrical connections involved with the installation of the stove.
Your stove operates on a 115 volt electrical source. We recommend that you use 14/2
115 volt underground wire during your installation. To avoid electrical shock disconnect
the electricity before performing your installation.
Your stove is equipped with a 115 volt aquastat controller. The pump(s) operate on 115
volts as well.
Aquastat Controller
Before firing the stove ensure that the aquastat is correctly programmed. While this is
done at the factory many factors can cause the programming to be lost and the default
programming may cause the stove to overheat and burn up. See section “Setting the
Aquastat” for details.

Grounding Rod
A properly installed grounding system will protect people from electrical shock help
safeguard expensive electronic equipment prevent electrolysis limit neutral-to-ground
voltage and satisfy the NEC along the way.
Use only a 4GA or larger wire with proper grounding clips. Grind paint away where the
wire attaches to the stove in order to get a solid electrical connection.
GFCI Outlet or GFCI Breaker
Install a GFCI outlet or GFCI breaker on the stove. This will protect the user and the
electronics and prolong the life of the stove. Installing an ordinary electrical switch
between the GFCI and the power supply coming into the stove will allow you to easily
switch off the power to the stove for maintenance. Using the GFCI reset button as a
switch would greatly shorten its life. The stove's pump(s) plug into this outlet
conveniently.
Thermostat
Install a second thermostat (110 volt line voltage thermostat) connecting it to your
existing home furnace. This will allow the heat from the outside stove to be distributed
throughout your home without your indoor furnace’s burner cycling on and off.
Your existing furnace thermostat should be set several degrees lower than the new
stove thermostat. This will allow the existing furnace to only turn on and heat your
home if the fire goes out in your outdoor stove.
IMPORTANT: Have a qualified electrician check to ensure that these changes do not
cause the electric motor to overload. Any modification to the existing furnace must be
made in accordance with the manufacturer’s specifications and performed by a
qualified licensed person in accordance with local building codes.
Plumbing
We recommend that you contact a licensed professional plumber to make all necessary
plumbing installations between the stove and your existing heating system or your
building(s). There are tips for the installation elsewhere in this manual and on our
website.

Initial Water Fill-Up
Attach a garden hose to the hose fitting on the return line pipe. Shut off the return line
ball valve and fill the entire system until water runs out of the vent pipe on the top of
the stove. Open the return line ball valve and run the pumps for 24 hours to purge the
air from the system and to check the plumbing for leaks. Check and refill the system as
necessary and pour 1 unit of sodium nitrite treatment solution into the vent pipe
located on the top of the stove.
This is a typical example of the plumbing diagrams for the back ports on your stove.
Stove Water Ports
The stove pump ports are shown here. The ports are female 1 inch NPT (National Pipe
Thread) and fittings are available at your local home improvement store.

SECTION 2 – GETTING TO KNOW YOUR STOVE
Stove Construction
Firebox
Our firebox is 5/16” thick which gives us one of the thickest fireboxes available.The
strongest structure is round and the weakest is square or rectangular. For longevity and
strength our firebox uses this round boiler design. Round designs have fewer welds;
therefore fewer spots for possible failure.
Water jacket
Our water jacket is 3/16” thick and is also a round design giving it maximum strength.
The water jacket surrounds the entire firebox of the stove to maximize heat transfer.

Sight Glass
A sight glass is a simple mechanical way to keep track of the water level in your stove.
With a quick glance you know that your stove has the correct amount of water. If you
do not see water in the sight glass water must be added to your stove. Commonly the
water level in the gauge will settle just below the halfway point.

Boiler Vent
The boiler vent is a port coming off of the highest part of the water jacket of the stove
and is used to vent air from the stove when it is filled. It is also used to prevent a
vacuum from forming when the stove is drained. The stove is a non-pressurized unit
and is ventilated to the atmosphere through the vent. The vent is also a good place to
pour the water additive (sodium nitrite) for your stove. It is not recommended to fill
your stove the first time through the vent tube because that could trap air in the
pumping system.
Chimney
The chimney is 8” schedule 40 steel. A regular 8” piece of stove pipe will fit into the
chimney of your stove. You could also use 8” insulated pipe.
Stoves with chimneys mounted out the side will have far more creosote than those that
have chimneys going out the top. The answer is simple. Unburned gases when exiting
into the chimney cool off condense and form creosote. Out-the-side chimneys run
much cooler resulting in excessive creosote buildup. Your stove has an ‘out-the-top’
chimney running through a diverter. Our stove is designed this way to be simple safer
and require less maintenance.
Check the caulk around the chimney and roof of your stove. Re-caulk as necessary. Your
local home improvement store will carry a high temp RTV silicone adhesive/sealant that
withstands up to 500 to 600 degrees.

Diverter
If you look at the top of the firebox you will see a metal box. This box is called a
Diverter. The diverter is mounted under the chimney. It is designed to push smoke and
heat to the back of the stove so that the stove heat does not go straight out the
chimney. The flapper in the diverter is there to aid in cleaning the chimney. If can be
removed or pulled back to clean the chimney.
Rear Access Door
The rear access door encloses the plumbing and electrical wiring for your stove. It is
held on with two knob bolts and slides out the bottom of the stove frame.
Electrical

Your stove comes with one electrical box containing aquastat wiring. You or your
electrician will probably add an additional box for your pump wiring. The stove is
prewired and ready for 115 volts.
Electronics
Aquastat Controller
The aquastat controller for your stove is designed for many heating and cooling and
high temperature applications. The probe temperature is displayed on a bright 3-digit
display. You are able to program the set point (SP) which is the temperature the
damper door will open and you are able to set the differential (R0) which is the
difference between the damper open and close temperatures. Setting the aquastat is
covered in ‘Setting the Aquastat’.
SECTION 3 – MAINTENANCE AND CLEANING
Before the eating Season
CAUTION – DO NOT START A FIRE IN T IS STOVE UNTIL OPERATING
INSTRUCTIONS AVE BEEN READ AND FULLY UNDERSTOOD.
Never start a fire in your stove without water The stove will burn up.

Make sure your stove is full of water (SIGHT GLASS) run the pumps and check for leaks.
Remember the pump is lubricated with water. It is normal for water to overflow the
first time you fire the stove and water expands. Once the stove finds its normal
operating level it is only necessary to note that level on the gauge and only add water
when the level drops significantly.
Inspect the rope seal around the inside of the door before lighting the first fire and a
few days after looking for any indications of a poor seal. A poor seal will cause the fire
to burn unregulated possibly resulting in damage due to overheating as well as poor
burning economy. The door must be closed and sealed for the stove to operate
properly.
End of the eating Season
Check the caulk around the chimney and roof of your stove. Re-caulk if necessary. Your
local home improvement store will carry a high temp RTV silicone adhesive/sealant that
withstands temperatures up to 500 to 600 degrees.
Check the rope seal around the inside of the door. Replace if necessary
Remove the rear access door and inspect the pumps and fittings for leaks.
Clean the outside of your stove. Many times there will be creosote on the roof and ash
around the door. This is a good time to take care of your stove.
Scrape the inside of the firebox and spray it down with kerosene mixed with automatic
transmission fluid PB Blaster or something that will prevent rust and corrosion.
Keep a bucket over the chimney to prevent rain from entering the stove during the off
season when the stove is not in use.
Drain and flush the water jacket then refill it with water and a unit of sodium nitrite
treatment. Then completely fill the stove to the top of the vent pipe with water. This
will eliminate the chance of the oxygen attacking the top of the firebox. Be sure to
recheck the water level before using the stove again at the start of the next heating
season.
Creosote
Creosote is a gummy foul smelling corrosive and extremely combustible substance
that if no precautions are taken will coat the insides of everything it comes in contact

with. It is formed when gases given off in the burning process combine and condense
on their way out of the chimney.
The firebox must be cleaned and rust protected during the off season. Scrape brush
clean the inside of the firebox and spray it down with kerosene mixed with automatic
transmission fluid PB Blaster or something that will prevent rust and corrosion.
Corrosion Control
Add 1 unit of sodium nitrite to the water jacket each year.
Install an anode rod. They are commonly used on water heaters to reduce rusting. They
also work for outdoor boilers. On your Ezboilers stove the anode rod can be connected
through the drain port which is the lowest port on the back of the stove. Simply add a
tee fitting to that port install the anode rod straight into the water jacket and install
your drain valve on the side of the tee. When you drain and flush the stove once a year
also remove the anode rod and inspect it. There is no way to predict how often it will
need to be replaced since water quality varies widely.
Install a 6′ grounding rod and ground the frame of the furnace. This will minimize
corrosion from electrolysis.
Keep the ash and coal pulled to the front of the firebox and add fuel to the top and
behind of this coal pile. Pay special attention to the left and right sides of the coal pile
where they touch the firebox. Move those edges around every day so that an
undisturbed corrosive ash line doesn’t form against the sides of the firebox.
Keep the firebox cleaned out and oiled in the off season.
Put a bucket or cap on the chimney in the off season to keep out rain.
Drain and flush the water jacket every year (sludge buildup in bottom of water jacket
can allow corrosion even if you maintain nitrite chemicals).

Water Maintenance
It is important that the water be drained every year and refilled with treatment and
water or as needed due to sludge and build up. Water treatment can be purchased
from Wood Boiler Solutions. Their website is: outdoorwoodfurnaceparts.com/ or local
customers can purchase it for $30 at our office in Hersey Michigan. Keep the empty
sodium nitrite bottle on hand for quick reference to the company’s website address.
Pumps
You should run your pumps at least once a month for 24 hours during the off season.
This will cycle the pumps and circulate the water and chemicals throughout your
plumbing system.
Sight Glass
If your sight glass becomes cloudy or hard to read it is serviceable. Simply remove the
nut fitting on the top and remove the glass tube. Clean the tube and reassemble. Make
sure the rubber washer on the underside of the nut is still there and is in good
condition. Do not over-tighten the nut.
SECTION 4 – OPERATING INSTRUCTIONS
Fuel Burning
Every day before you load fuel into your outdoor stove you will want to pull the ash
and wood burning coal pile to the front of your firebox. Make it into a heaping pile and
then load fuel on and behind the coal pile. The fire will burn through the pile and turn it
to ash. Do not pull the coals tightly against the front plate. Leave them back a few
inches or more. Be sure to stir the ashes where they touch the sides of the firebox as
well.
Another benefit of raking ashes forward each day is that it will make it easier when you
need to empty the ashes every 4-6 weeks or as needed. The ashes will already be in
the front and more of the firebox will be available for heat transfer to the water jacket.
This will make your outdoor wood stove come to temperature faster and burn less
wood. If you allow your firebox to fill half way up with ashes you will minimize the heat
transfer area and will have a tough time finding room for fuel.

Ash Disposal
Ashes should be placed in a metal container with a tight-fitting lid. The closed container
of ashes should be placed on a noncombustible surface well away from all combustible
materials. If the ashes are going to be buried in soil or otherwise locally dispersed they
should be left in the closed container until all cinders have thoroughly cooled.
Stove Operating Checklist
•Check The Water Level
•Inspect The System Plumbing
•Verify That The Pump(s) Are Running
•Verify That The Chimney Is Installed And Clear
•Inspect The Door Gasket
•Inspect The Door Tightness
•Verify The Aquastat Operation
•Review All Safety Precautions
Electrical
Supplied Electrical
Your stove comes with one electrical box and a supply wire that will power the Aquastat
controls. This is a 115 volt circuit.
Setting the Aquastat
The aquastat controller for your stove is designed for many heating and cooling
applications. Proper adjustment of the aquastat is important for proper stove
operation. The display will show the current water temperature. To enter into the
programming mode to adjust the settings press the “set” and the “down arrow”
buttons at the same time. Those are the 2 bottom buttons.

Then press and hold the ‘set’ button. It can take 10-20 seconds but when it shows
‘0’ in the display release the ‘set’ button. You are now in the programming mode. From
here out in the instructions do not hold the buttons. Just a simple single push is all that
is required.
Press the ‘set’ button one time and ‘SP’ will display. This is the set point. Pressing the
‘set’ one more time will display the current set point. The factory setting is 180 but
yours may be different. Use the ‘ ’ up arrow and ‘ ’ down arrow to adjust the setting ▲ ▼
to your desired temperature. 180 degrees works well. Even though the stove is called a
“boiler” you would never want the water to actually boil. Pressing the ‘set’ button will
lock the setting in and return you to the ‘SP’ display.
Press the ‘ ’ up arrow button one time and ‘r0’ will display. This is the temperature ▲
differential. Press the ‘set’ button and it will display the current differential. The factory
setting is 5 (or 10) but yours may be different. This controls the temperature range.
With SP=180 and r0=5 the damper door will open at 175 and close at 180. Use the ‘ ’ ▲
up arrow and ‘ ’ down arrow to adjust the setting to your desired temperature. We ▼

have found that setting it to 7 works very well. Pressing the ‘set’ button will lock the
setting in and return you to the ‘r0’ display.
Press the ‘ ’ up arrow button one time and ‘r1’ will display. This is not used and should ▲
remain at 0.
Press the ‘ ’ up arrow button one time and ‘r2’ will display. This is the maximum set ▲
temperature. Press the ‘set’ button and it will display the current maximum. The RWS
factory setting is 180. This will be the maximum temperature that can be set in the ‘SP’
value. Use the ‘ ’ up arrow and ‘ ’ down arrow to adjust the setting to your desired ▲ ▼
temperature. Leaving it at 180 prevents anyone from accidentally adjusting the set
point too high and damaging the stove. Pressing the ‘set’ button will lock the setting in
and return you to the ‘r2’ display.
Press the ‘ ’ up arrow button one time and ‘d0’ will display. This is the heating / cooling▲
switch setting. THIS MUST BE SET TO ‘Ht’ or your stove will not function properly. Press
the ‘set’ button and it will display the setting. The RWS factory setting is ‘Ht’ but if it
shows ‘Co’ you MUST change it. Use the ‘ ’ up arrow to change the setting to ‘Ht’. ▲
Pressing the ‘set’ button will lock the setting in and return you to the ‘r2’ display

To exit the programming mode press the ‘set’ button and the ‘ ’ down arrow at the ▼
same time. This will return you to displaying the current temperature.
Quick Adjustment of the Run Temperature
You can quickly adjust the run temperature by pressing the ‘set’ button once. The
screen will say ‘SP’. Press the ‘set’ one more time. The display will show the current set
temperature. Use the ‘ ’ up and ‘ ’ down arrows to adjust the temperature. Press the ▲ ▼
‘set’ button once and this will set the temperature set point.
To exit the programming mode press the ‘set’ button and the ‘ ’ down arrow at the ▼
same time. This will return you to displaying the current temperature.
SECTION 5 – SPECIFICATIONS
EZ-Classic
Approximate Heating Capacity 5 000 sq. ft.
Water Capacity150 gallons
All Ports 1″ NPT
Door Size 24″ x 24″
Firebox Diameter 37″ Round
Firebox Length 47″
Chimney Size 8″ Schedule 40
Approximate Weight 1 450 lbs.

The EZ-Classic model firebox size is 37” x 47” with a door size of 24” x 24” and the
stove weighs around 1,450 pounds. The EZ-CLASSIC is a good size for the average
house and small garage. It holds 150 gallons of water.
EZ-Pro
Approximate Heating Capacity 7 500 sq. ft.
Water Capacity 200 gallons
All Ports 1″ NPT
Door Size 24″ x 24″
Firebox Diameter 37″ Round
Firebox Length 59″
Chimney Size 8″ Schedule 40
Approximate Weight 1 800 lbs.
The EZ-Pro model firebox size is 37” x 59” with a door size of 24” x 24” and the stove
weighs around 1,800 pounds. The EZ-Pro is a good size for a large house or an average
house plus garage. It holds 200 gallons of water.
Note: The quality of home insulation and windows outdoor temperature and type of
fuel used will all affect the burn time and square footage rating.
SECTION 6 – PARTS
Please call to confirm the current pricing of parts: [phone]
DOOR GASKET

Our Part Door Rope Seal $3.00 per ft 1” standard fiberglass firedoor rope gasket. Glue
in place with high temperature silicone adhesive.
SOLENOID
Our Part Solenoid $45.00 Grainger Part 4×420
Manufactured by Dormeyer
Model 2005-M-1
SIG T GLASS
Our Part Sight Glass $75.00 Grainger Part 1U614
Model G901-4
Manufactured by LDI INDUSTRIES
PUMPS