EZCast Beam J2 User manual

Quick Start Guide
Model: EZCast Beam J2
Guide de démarrage rapide
Guía de inicio rápido
Инструкция по началу работы
Vodič za brzi početak
Rychlý návod
Schnellstartanleitung
Snelstartgids
Vodič za hiter začetek
Ghid de inițiere rapidă

How to use the projector:
（1）Do not point the projector lens towards human eyes. The bright light can cause
damage to eyes.
（2）Do not block the air vents. Blocked venlaon may cause overheang and
damages to the projector electronics and components.
（3）Do not use chemicals, detergents or water to clean the projector. Moisture and
chemicals may corrode the projector circuit boards.
（4）Do not place the projector within reach of children.
（5）Only use the projector in dry environment with good venlaon.
（6）Do not store the projector in extremely hot or extremely cold temperatures.
Extreme heat and cold can reduce the component lifeme of projector. Recommend-
ed working environment is between 5℃~35℃.
（7）Do not aempt to dry the projector in heang devices, such as dryer,
microwave etc.
（8）Do not squeeze or apply excess pressure to the projector. The projector may
be damaged from the pressure.
（9）Do not throw, knock or shake the projector. The projector may be damaged
from the vibraon.
（10）Do not aempt to open the projector. Please refer to qualified customer
support.
（11）Do not aempt to service the projector. Please refer to qualified customer
support in the event of projector malfuncon.

V+
V-
Back
（Remote control is powered by
two AAA baeries (not included)）
Power Off Only
Keystone
Power
Understand EZCast Beam J2 and Remote Controller

(1) Power on the projector with the supplied power adapter.
(2) LED turns green to indicate idle state.

Advanced Setting: Projection Location, Brightness,Contrast, Auto V Keystone,
V. Keystone, H. Keystone,4 Corner Correction settings.Use up/down Arrows to
choose function,and left/right Arrows to adjust settings.

No power, LED off,cannot
power on
1. Check the Quick Start Guide for the correct screen mirroring
funcon.
2. Shorten the distance between smart device and projector for best
screen mirroring quality.
3. Make sure the smart phone is connected to the correct Wi-Fi
network SSID.
Unable to recharge smart
phone when projector is
unplugged from power
Common issues
LED on, cannot power on
Cannot screen mirror
Cannot stream media
Remote not responsive
Auto V Keystone not
working
1.Select "Seng>Advanced Seng" and confirm "Auto V Keystone" is
On.
2.If aer step 1, the images are sll not rectangular, then follow the
steps below to calibrate the projector:
Place the projector on a level surface, select "Seng>Advanced
Seng" and turn Off "Auto V Keystone".
Then turn On "Keystone Calibraon", and wait unl "Keystone
Calibraon" turns itself Off aer calibraon.
Finally turn On "Auto V Keystone" to confirm the feature is funconal.
Press and hold the Power buon for 10 seconds to shutdown.
1. Replace remote baeries
2. Pair the remote with your projector again. Pairing procedure:
simultaneously hold down Volume+ and Volume- keys for 3 seconds,
once the remote's flashing red light becomes constant, the pairing
process is complete, and you can begin using the remote normally.
Did not short press Power before connecng smart phone.
Check the internet connecon for your smart device.
Check the power adapter for loose connecon, press the Power
buon to turn on projector.
Check the power adapter for loose connecon.
Soluons
Cannot shutdown
projector
Troubleshoong
Common issues and soluons:

1. 注意事項
如何正確使用設備：
（1）請勿將鏡頭朝向人眼，避免開機後鏡頭強光對眼睛造成傷害。
（2）請勿堵塞設備的進/出風口，避免設備無法正常散熱對 內部電子器件造成損壞。
（3）請勿用化學製品、清洗劑或清水來清洗設備，以及避免雨水、濕氣和含有礦物質液體腐
蝕電路板。
（4）請將設備及其部件和配件放在兒童觸摸不到的地方。
（5）請確保設備在乾燥通風的環境下使用。
（6）請勿將設備存放在過熱或過冷的地方，高（低）溫會縮短電子器件的壽命。允許使用環
境為5℃~35℃。
（7）請勿將設備放入任何加熱設備（如乾燥機、微波爐等）進行烘乾。
（8）請勿用力擠壓設備或在其上方放置重物，以避免損壞設備。
（9）請勿扔放、敲打或強烈震動設備，導致內部電路板損壞。
（10）請勿試圖私自拆裝設備。如有問題，請聯絡售後服務。
（11）請勿自行維修任何產品。若設備或任何部件不能正常工作，應及時諮詢售後服務或返
廠維修。
（12）注意：用錯誤型號電池更換會有爆炸危險，務必按照說明處置用完的電池
（13） 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變
更頻率、加大功率或變更原設計之特性及功能。
（14）低功率射頻電機之 使 用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線
電通信。 低 功 率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干
擾。
本產品為高亮度光源，切勿凝視或直視鏡頭光束，可能傷害眼睛。特別注意勿讓兒童直接凝
視鏡頭光束，可能傷害眼睛。

認識EZCast Beam J2主機及遙控器
遙控器由兩節AAA電池供電
（電池不包括在內）

（1）將隨機標配的電源供應器連接投影機電源埠。
（2）通電後機身側面LED綠燈常亮，投影機進入待機狀態。

(5) 高級設定：此選項中有：投影位置、亮度、對比度、自動垂直梯形校正、垂直梯形校正、
梯形校準、水準梯形校正、四角校正，八項設置，按上下方向鍵選擇功能表，游標停在的當前
功能表，按左右鍵可直接調整