eZLO VistaCam 1103 User manual

1
Quick Start Guide
VistaCam 1103
Quad HD Outdoor Wi-Fi Camera

2
What’s in the Box
Camera
Ethernet Cable Wi-Fi Antenna
Power Adapter
Contents
What’s in the Box...............................................................................2
Camera Connections .......................................................................3
Before You Get Started... ................................................................3
Choosing Wi-Fi or Ethernet............................................................4
Initial Setup..........................................................................................4
Before You Mount Your Camera ...................................................5
Testing Wi-Fi Strength .....................................................................6
Mounting Your Camera....................................................................6
Making Connections.........................................................................8
Using Your Camera ...........................................................................8

3
Camera Connections
1. Before You Get Started...
• Wi-Fi and a broadband internet connection.
• An Ezlo Plus or Ezlo Secure Smart Hub.
• An iOS or Android phone or tablet with the Vera Mobile app
installed (visit ezlo.com/app to download).
• A power outlet near the desired camera location.
• A drill and Phillips screwdriver bit.

4
2. Choosing Wi-Fi or Ethernet
For maximum flexibility, the VistaCam 1103 can be connected to
your router wirelessly (Wi-Fi) or by ethernet cable.
Which should you choose?
Wi-Fi
Wireless connections is the most convenient connection
method, as there’s no need to run additional wiring to the
camera’s location. However, in homes that have poor Wi-Fi
coverage or if you experience camera connection issues, Wi-Fi is
not recommended.
Ethernet
Using a direct ethernet connection between the camera and
your router is the most reliable method of connection. This is
recommended for camera locations that may be far away from
your Wi-Fi router.
3. Initial Setup
It’s best to perform the initial setup of the camera near your
home router.
1. Attach the Wi-Fi Antenna to the back of the camera by
screwing it in tightly (for ethernet connections, connect
your camera to your router with the included ethernet
cable).
2. Open the Vera Mobile app on your smart phone or tablet
(visit ezlo.com/app to download).
3. From the Main Menu, select Devices, then tap the +symbol
in the top right corner.
4. Select Cameras, then VistaCam 1103.

5
5. Follow the instructions in the Device Pairing Wizard to
complete setting up your camera.
6. Once you have finished with the Device Pairing Wizard, you
can find and view your camera’s video feed by selecting
Cameras from the Main Menu.
7. Now you can disconnect the power (and ethernet cable,
if applicable) and mount your camera in your desired
location (see next page).
Problems? Our technical support team, is available 7 days a
week, 6am-10pm (CDT)
Email: [e-mail]
Phone: [phone]
4. Before You Mount Your Camera
When choosing a location to mount your camera, it’s important
to keep the following in mind:
• Avoid aiming the camera in a direction that would point
directly into the sun (adjustments to this can easily be
made after mounting).
• Point your camera at the center point of the area you
wish to provide video coverage and be aware of any trees,
shrubs, or other objects that could block the camera’s view.
• If you’ve paired your camera using a Wi-Fi connection,
ensure your install location has good Wi-Fi signal coverage.

6
6. Mounting Your Camera
Using an appropriately-sized bit, drill two pilot holes 1-¾” apart.
You can also use the template on the next page to mark your
pilot hole locations.
Using a 3/4” bit, drill a wiring access hole centered between
your two pilot holes (to accommodate the camera’s wire
connections through the wall).
After drilling these holes, insert the camera’s wires through the
wiring access hole and secure the camera to the wall with the
two provided screws.
Note: Installations into softer wall materials will require use of
the included plastic wall anchors.
5. Testing Wi-Fi Strength at the camera location
1. Bring your smartphone near your preferred camera
location.
2. Make sure your phone is connected to your home Wi-Fi
network.
3. With your phone, visit a website or stream an online video.
4. If websites and videos load and play quickly, then the
location most likely has acceptable Wi-Fi coverage.

7
1-¾”
¾”
7. Make Your Connections
8. Using Your Camera
Make the following connections behind the wall where you
mounted the camera:
• Plug the camera’s power adapter into a wall outlet or
extension cord, then connect it to the camera’s power
connector.
• For ethernet installations, connect an ethernet cable
directly between the camera and internet router.
After finishing the previous step, wait two minutes for the
camera to power up and reconnect to the network.
Now you can test the camera’s functionality by opening the
Vera Mobile app, selecting “Devices”, then selecting the camera
that you’ve named during the wizard.

8
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receivingantenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer
could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.

ISED Statement
English:This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes
aux RSS exemptés de licence d'Innovation, Sciences et Développement économique Canada.
L'exploitation est soumise aux deux conditions suivantes :
(1) Cet appareil ne doit pas provoquer d'interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de
provoquer un fonctionnement indésirable de l'appareil.
l'appareil numérique du ciem conforme canadien peut - 3 (b) / nmb - 3 (b).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure
and compliance.
cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du
cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des
données canadiennes sur l'exposition aux champs rf et la conformité.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled
environment.
Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada établies
pour un environnement non contrôlé.
This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et
votre corps.