Faithfull FAI AUAXLE3 User manual

IMPORTANT
It is essential that you read the instructions contained in this manual before using the axle stands
for the rst time. Failure to follow these instructions could result in damage to the product, property
damage or personal injury. This manual should be stored safely for future reference.
Folding
Axle Stands
3 / 6 Tonne
FAI AUAXLE3
FAI AUAXLE6

Visual inspection should be made before
each use of the stands, checking for
cracks, cracked welds and missing and / or
damaged parts. Any stand that appears to
be damaged in any way must be removed
from service immediately.
Because of the potential hazards associated
with the misuse of equipment of this type,
no modications should be made to the
product. Attempting to modify this product
may void the manufacturers warranty.
Specications
Capacity: 3,000kg
Minimum Height: 282mm
Maximum Height: 420mm
Base Dimension: 200 x 180mm
Manufactured from high quality carbon steel, these stands feautre space saving folding
legs for easy storage, large feet to help spread the load and a pin and chain adjustment
and locking system.
Folding Axle Stands
A: Saddle
B: Centre Column
C: Locking Pin
D: Pawl
E: Control Lever
Before Use
Check that the stands are in good order and
condition and that no damage has been
sustained during transit. Familiarise yourself
with the folding mechanism and the folding
legs.
Insert the centre column in the centre
tube, adjust to height required and insert
the locking pin. When lowering the centre
column, hold the centre column rmly before
removing the pin. Failure to do so will allow
the centre column to free fall through the
centre which may be dangerous.
Maintenance & Inspection
A
Capacity: 6,000kg
Minimum Height: 382mm
Maximum Height: 600mm
Base Dimension: 290 x 260mm
FAI AUAXLE3
FAI AUAXLE6
B
C
D
E

Visual inspection should be made before
each use of the stands, checking for
cracks, cracked welds and missing and / or
damaged parts. Any stand that appears to
be damaged in any way must be removed
from service immediately.
Because of the potential hazards associated
with the misuse of equipment of this type,
no modications should be made to the
product. Attempting to modify this product
may void the manufacturers warranty.
Operation
1. Ensure the maximum load does not
exceed rated capacity.
2. Refer to vehicle owners hand book
for correct jacking procedure. Check
to ensure that the jacking points are in
suitable condition.
3. Ensure the vehicles brakes are on
and wheels are chocked. Vehicles with
automatic gear boxes must have the
gear lever in the ‘Parked’ position.
4. Ensure the stand legs are fully extended
and adjust the height of the stand to
correspond with the raised vehicle.
5. Hold control lever up while lifting saddle
shaft to desired height. Push control
lever down to lock pawl into teeth located
in centre column. Make sure pawl is
fully engaged into teeth.
6. Insert the locking pin, ensuring it is
pushed all the way through and out the
other side.
7. Slowly and carefully lower the load onto
the stands.
Before Use
Check that the stands are in good order and
condition and that no damage has been
sustained during transit. Familiarise yourself
with the folding mechanism and the folding
legs.
Insert the centre column in the centre
tube, adjust to height required and insert
the locking pin. When lowering the centre
column, hold the centre column rmly before
removing the pin. Failure to do so will allow
the centre column to free fall through the
centre which may be dangerous.
Maintenance & Inspection
Safety Precautions
•Ensure axle stands are in good
condition. DO NOT use if damaged.
•Ensure you familiarize yourself with the
product and its folding mechanism.
•Ensure the locking pin is in place before
operation.
•Vehicles with automatic gear boxes
must have the gear lever in the ‘Parked’
position before operation.
•When raising the stands centre column
to engage load, ensure the dead centre
of the stands saddle is located under the
vehicles jacking point.
DANGER! Great care must be taken to
ensure you lower the vehicle load slowly
and carefully onto the stands.
• Do not use on soft ground or tarmac.
Use only on concrete.
• Do not use a single stand. Use only
in pairs.
• Do not overload axle stands beyond
rated capacity.
• Do not use four stands on one vehicle.
• Do not jack up the end of the vehicle if
the other end is already on stands.
• Do not use on three wheeled vehicles or
trailers. Refer to makers instructions.

FAITHFULL TOOLS
Phoenix House,
3 White Lodge Business Estate,
Hall Road, Norwich, Norfolk,
NR4 6DG, United Kingdom
E-mail: [email protected]
www.faithfulltools.com
FAI AUCREEP Folding Car Creeper
FAI AUSEAT Steel Seat on Wheels
FAI AUJACBOT2 Bottle Jack 2 Ton - 2000kg
FAI AUJACBOT4 Bottle Jack 4 Ton - 4000kg
FAI AUJACBOT6 Bottle Jack 6 Ton - 6000kg
FAI AUCABLE2 Cable Puller 2 Ton - 2000kg
FAI AUCABLE4 Cable Puller 4 Ton - 4000kg
FAI AUAXLE2 2x Folding Axle Stands 2 Ton - 2000kg
FAI AUAXLE3 2x Heavy-Duty Axle Stands 3 Ton - 3000kg
FAI AUAXLE6 2x Heavy-Duty Axle Stands 6 Ton - 6000kg
FAI AUJACTRO15 Trolley Jack 1.5 Ton - 1500kg
FAI AUJACTRO3 Trolley Jack 2.5 Ton - 2500kg
Other products available in this range: