Fanvil iW30 Original operating instructions

SIP Speaker iW30
Quick Installation

Icons
Description
Feature
Picture
Power
DC Power
Input port
Input Range:+12～+24V DC
(Notice: Plus-n-Minus connection of the Power)
WAN
WAN port
10M/100M Adaptive Ethernet port, connected to the
network
LAN
LAN Port
10M/100M Adaptive Ethernet port, connected to the
computer (which can be configured to routing mode, or to
bridge mode) or IPC camera.
NET
The
Network
Light
1、The network get through , and the light put out
2、The network can’t get through , and the light blink fast
within 0.5s
3、The network get through but registration fail , and the
light blink slowly with 1s
VOLUME
/RST
button
1、Press and hold volume down button for 3
seconds; the door phone would report the IP address
by voice, and the voice volume will go down by single
press the button.
2、Long press the volume plus button for 10
seconds, the speaker issued a rapid beep, and then
quickly press the three volume plus the button, beep
stopped. Wait 10 seconds, successfully switch to
dynamic IP after the system automatically voice
broadcast IP address. Switching again will become a
fixed IP address, and the voice volume will go up by
single press the button.
3、Press the reset button for 3 seconds, the device
automatically restarts and restores the factory
configuration.
Interface Explanation
Interface Diagram

AUDIO
Audio
output
Connect audio port to output the audio headphones or
external speakers.
Step One: Connect to the network
The product factory default network mode is static IP address 192.168.1.128.Connect the
end of network cable to the device WAN port, another end is connected to the LAN port of the
router, then the hardware connection is completed. Normally, you should set your network to
DHCP mode.
SIP Speaker Configuration
No server mode
(P2P mode)
SIP Server mode
VOIP Phone
Audio stream
（SIP/P2P）
SIP Speaker
PC SIP Phone Software
Mobile SIP Phone Software

Step Two: Get the device IP Address:
Method 1:
Use the default IP scanner tool to get it: Network Scanner
1) Install the scanner tool: Network Scanner;
(Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe )
2) Ensure the working computer (installing IP scanner tool, exe.) is in the same local network
with the corresponding device;
3) Run the tool (Network Scanner.exe), to search the IP address of corresponding device within
the network.
Method 2:
Long Press “ ”button for 3 seconds, the intercom will report the IP numbers by itself.
Step Three: Log in the WEB admin interface of the device
Input IP address (e.g.: http://192.168.1.128) the Web browser, the default user name: admin,
password: admin.
Step Four: Modify the device description

Step Five: Add SIP account
Step Six：The Volume adjustment
Set the device volume size, as shown below, click [Apply].
Hands-free volume setting: normal call speaker volume size.
Broadcast output volume: server music broadcast speaker volume size.
Signal volume: call ringing, power back to ling, correct tone, error tone and other volume size.
Microphone Input Volume: microphone volume size
Step seven：Setting Speaker Settings mode
The Speaker Settings default mode is <panel speaker>，the output power is limited to 10W。
If external loud speaker user for broadcasting, It can be adjusted to the <external speaker> mode，
You need to choose the corresponding value of External Speaker Power according to the power

supply input voltage：POE/10W,12V/2A 10W,18V/2A 20W,24V/2A 30W。
Step eight：Set the camera (if not connected can skip)
<Local>mode：Connect the original camera. You just need to input the factory authentication
code of the original camera to active the function.
<External>mode：To connect a non-original camera, insert the camera into another LAN or LAN
port. Configure the following parameters and click [Apply].