Fat toad XPF8017 User manual

Fat Toad| 11408 Hwy 64 W, Tyler, TX 75704 |
[e-mail] | www.FattoadPro.com
www.FattoadPro.comwww.FattoadPro.com
www.FattoadPro.com
Fat Toad™stands and accessories are
manufactured in several innovative factories
responsible for developing products that address
the newest needs and trends of the current
market. We take pride in the Fat Toad™brand and
endeavor to be on the forefront of the musical
stands and musical and lighting accessories market.
Performance Issue, Uneven or Unstable- Make
sure all nuts and bolts are tight on the product. If they
are, then loosen all nuts and bolts 1 full turn counter-
clockwise, then go back and tighten each bolt only ½
turn tight. Then do a final tighten turn for another ½
turn tight. Next, Make sure there are not any missing
nuts or bolts. Third, ensure all parts on the product
are not broken or defective. Finally, Re-read the
assembly instructions or watch the product
demonstration video to ensure you have correctly
assembled or are using the product properly with
factory specifications.
Missing Parts- The pictures, videos and images
shown in this manual might have changed style or
count due to the product being redesigned. So in rare
cases the part may no longer be included or of a
different style. However, if you think you are missing
a part that is necessary to the assembly and use of
your product, then first carefully double check all
packaging for any parts you think are missing. Some
parts might be hiding in the packaging or loose in an
inner box.
User Manual
For current product specifications, please to go
www.FattoadPro.com and type the model number into
the search bar. Locate the product listing to view the
current factory specifications. Thank you for purchasing the Fat Toad DJ Booth Stand
(Model XPF8017). Your product comes with a 1-year
factory warranty from purchase date. Please read all
assembly instructions prior to assembling your new
stand. Pictures that may aid in assembly can be found
by going to www.Fattoadpro.com and typing XPF8017
into the search bar.
Fat Toad| 11408 Hwy 64 W, Tyler, TX 75704 |
[e-mail] | www.FattoadPro.com

Step 3 –(Figure 3) The
removable tabletop
(PART D) installs using
the pre-installed “C
channels” placed over
the top of the first
horizontal frame rails
that are open all the
way around. Begin by
opening the right side
Step 1 –Stand the
mainframe (PART G)up in
front of you with the
center hinges facing you.
Then grab the two panels
on each side (2 panels in
each hand) and unfold
evenly towards you.
(Figure 1)
Please scan the QR Code below for the product
demonstration video. Or go to the URL shown here and find
the product video. www.FattoadPro.com/Videos
Step 2 –Unfold the two
remaining panels (one on
each side) evenly away
from you. (Figure 2)
Step 4 –Install the four
pole clamps (PART C) as
shown in Figure 4. Place
the C-shaped clamp
around the vertical pipe
and insert the bolt
through the holes. Twist
the knob to secure.
There are two on each
side -- one at the top and
one at the bottom.
Step 5 –The vertical pipes
(PART H) can then be
installed (one on each side)
by sliding down into the
clamps installed in Step 4.
For stability, these can be
slid all the way to the floor
and the knobs on the
clamps tightened. (Figure 5)
Step 6 –The four scrim
sheets (PART F) can then be
installed using the pre-attached Velcro. These sheets may
be washed using a gentle detergent either by hand or in a
washing machine set on gentle cycle. DO NOT PLACE IN
DRYER. HANG DRY ONLY. (Figure 6)
Step 7 –Take the 1 pc of “I-Beam” Truss Sections (PART E)
and insert 1 pc of Beam Connectors (PART A) to one end.
(Figure 7) This part will be the center I-Beam of the truss
section. Secure these using a bolt, washer, nut and
wingnut. Repeat this process on the other side of the I-
beam.
of the frame slightly and placing the tabletop “C clamps”
over the rail. Then gently pull the right side back into
place setting the rest of the tabletop “C clamps” on top
of the rail. You may need to use some pliers to gently
open one or more of the “C clamps” so they sit on the
rail.

Step 8 - Then place
the other I-beam
(PART E) onto the
center connectors
(PARTS A &E)and
secure the remaining
bolts, washers, nuts
and wingnuts. (Figure
8)
Please scan the QR Code below for the product
demonstration video. Or go to the URL shown here and find
the product video. www.FattoadPro.com/Videos
Step 9 –Place the connected I-beam (PART E) onto the
upright poles (PART H) as shown in Figure 9 and tighten
the knobs.
Step 11 –Install the remaining bolts into the predrilled
holes on the I-beam in the positions you want your lights
using a phillips head screwdriver and hand wrench. Then,
place your light or accessory over the bolt and use the
wingnut to secure (Figure 11). The stand is rated to hold
60lbs. Overloading the stand could cause structural
failure leading to damage of the stand, your equipment,
or even yourself.
Step 10 –To raise or lower
the lighting truss, loosen the
hand knob near the
connection of the upright
poles (PART H) (Figure 10).
Be sure to raise and lower
these poles evenly to avoid
damage to your stand, your
lights, or yourself.
Please note that hardware bolts to assemble the stand
maybe screwed into the parts themselves. So, for
example, if you are missing a bolt that goes into the
bottom base support tube, then look at the end of the
bottom base support tube and you will see that hardware
bolt is already screwed into the stand. All you need to do
is unscrew that bolt and then screw it back in to
assemble the two parts that connect on that end. If the
stand is wobbly loosen up each bolt on the stand slightly.
Then tighten up 1 bolt all the way as much as it will
tighten. After that start on the next bolt that is
completely opposite of the 1st bolt that you tightened.
For example, if you first tightened up the bolt in the top
right of the stand, then next start to tighten up the bolt
on the bottom left. Keep going in order of the opposite
bolt that you tightened up last. Once you are done,
repeat the process of going through and tightening up
the bolts one more time.

[e-mail]11408 Hwy 64 W, Tyler, TX 75704
Fat Toad
| | | www.FattoadPro.com