Federal Signal Corporation CAMCCD-SCNTSC Service manual

Safety Message to Installers
People’s lives depend on your safe installation of our products. It is important to read, understand and follow all
instructions shipped with the products. Listed below are some other important safety instructions and precautions you
should follow:
• Donotinstallequipmentorroutewiringinthedeploymentpathofanairbag.
• Ifavehicleseatistemporarilyremoved,verifywiththevehiclemanufactureriftheseatneedstobe
recalibratedforproperairbagdeployment.
• Althoughthecameraiswaterproof,repeatedlyexposingittodirect,high-pressurestreamsofwater(asfrom
a pressure washer) is not recommended.
• Whendrillingintoavehiclestructure,besurethatbothsidesofthesurfaceareclearofanythingthatcouldbe
damaged.
• Refertotheinstructionspackedwithrelatedproductsforadditionalprecautionsandinformation.
• Filetheseinstructionsinasafeplaceandrefertothemwhenmaintainingand/orreinstallingtheproduct.
Mounting the Camera
Thiscameraisrecommendedforinstallationoneithertheleftorrightsideofavehicle.Typically,thetrigger
wireforthecameraisconnectedtotheturn-signalcircuitofthevehicleforautomaticviewingwhenthevehicle
isturning.Thecameraisalsoequippedwithnight-visionandaudiocapability.
1. Locateasuitablemountingareaonthevehiclefreefromobstructionssuchaswallbraces,wires,brakeor
fuel lines, or other impediments.
2. SeeFigure1onpage2.Toaccessthegasketasaguideformarkingthepositionsofthemountingholes,
remove the two screws from beneath the front cover.
3. Positionthegasketoverthemountinglocationandmarkthecenterofthethreemountingholesandthe
cable hole.
4. Removethegasketanddrilla3/4-inchcable-routingholeandthree1/16-inchmountingholes.
5. Installthegasketontothemetalbracket.
6. Routethecameracablethoughthecable-routinghole.
7. Alignthecamerabracketoverthedrilledholesandattachitwiththethreeself-tappingscrews.
8. Beforeinstallingthecoversonthecamera,seethenexttwosections.
Adjusting the Camera for the Right or Left Side
Youcanadjustthecameraassemblyinsidethehousingforeithertheleftorrightsideofthevehicle.Iftheimage
on the monitor appears upside down on the preferred installation side of the vehicle, remove the two adjustment
nutsandipthecameraassembly180degrees.Theninstallittoswitchthecamerafromaleft-side-viewcamera
toaright-side-viewcameraorvice-versa.Reinstallthetwonuts.
25500057A REV. A 1112
Installation Instructions for the
Model CAMCCD-SCNTSC Side Camera

Connecting the Camera Cable
Thesidecamerahasthesecablingoptions:
a) acameraextensioncablethatcanbeeither:
• oneCAMCABLE-SHORT/-5/-10/-15/-20/-40or
• twoCAMCABLE-SHORT/-5/-10/-15/-20connectedinserieswithadapterCAMCABLE-EXT
that is connected to:
• eithertheCAM1 or CAM2inputontheinput/power/triggerwiringharness(CAMADP-INT-2)ofthe
CAMLCD-INT-56/CAMLCD-INT-70monitoror
• oneofthefourcamerainputsontheCAMBOX-4NTSC/CAMBOX-4PALcontrolbox(forusewiththe
CAMLCD-70monitor)or
• oneofthefourcamerainputsontheinput/power/triggerwiringharness(CAMADP-INT-4)ofthe
CAMLCD-INT-70-B
or
b) aspecialDVRsystemcamera-extensioncablethatisconnectedtooneofthefourcamerainputsonthe
CAMDVR-4-B
CustomerSupport
FederalSignalCorporation
Phone:1-800-264-3578,1-708-534-3400
www.fedsig.com
Installation Instructions for the Model CAMCCD-SCNTSC Side Camera