Fema Electronica K40-CR User manual

Series K . K40-CR
Chronometer, me counter
Chronometer and me counter, with 20 mm digit height. Congurable with up and down counng
modes. Independent controls for start, stop and reset. Display modes in decimal format and sexagesi-
mal (clock) format. Standard 96 x 48 mm size (1/8 DIN). Reading with 4 digit display. Fast access to
alarm setpoints, special modes for counng exceeded me and totalized counng mes, ‘on power
up’ funcon, congurable led brightness. Universal AC and DC power. Up to 3 oponal modules for
output and control (relays, transistor, control SSR, analog outputs, Modbus RTU communicaons, RS-
485 ASCII, RS-232, ...) www.fema.es
Tel. [phone] inf[email protected]
User’s Manual
ELECTRONICS FOR INDUSTRIAL AUTOMATION
PANEL METERS . SIGNAL CONVERTERS . LARGE DISPLAYS
PANEL METERS
3620r05

FEMA ELECTRÓNICA . Series K . K40-CR
2
1. Panel meter K40-CR
Chronometer and me counter, size 96 x 48 mm (1/8 DIN), with 20 mm digit height
Panel meter 96 x 48 mm (1/8 DIN) and 4 digits with 20 mm digit
height, and funcon chronometer and me counter. Time displayed
in dierent formats covering hours, minutes, seconds and days.
Reading congurable in decimal and sexagesimal (clock) formats. Up
and down counng funcons, with congurable preset value.
Controls
Independent controls for ‘start’, ‘stop’ and ‘reset’ (see secon 1.6).
Controls acvated by default through free potenal contacts. Con-
gurable for acvaon with other control signals (NPN, PNP, induc-
ve, ...).
Reset
Reset control is provided by connecon at the rear of the instrument,
congurable to acvate by edge or by level. Front reset congurable
at the ‘LE’ keypad (see secon 1.7). Automac reset congurable
when reaching an alarm setpoint (see secon 1.7).
Special funcons
Special funcons with acvaon by connecon at the rear of the in-
strument. Includes control for counng direcon, total accumulated
mes, total exceeded me, hold of display reading and memory of
cicles (see secon 1.12.2).
Alarms
Independent alarms congurable as maximum or minimum, with
congurable acvaon and deacvaon delays and oponal invert-
ed acvaon of the relay. Alarms congurable in ‘normal’ mode or
‘repeat’ mode. In ‘repeat’ mode the alarm acvates every me the
congured setpoint me has passed (see secon 1.12.4).
The ‘on_alarm’ parameter allows to associated a predened funcon
to the acvaon of the alarm. Available funcons are : stop counng,
acvate the reset, set reading to ‘0’ or connue. Use ‘on_alarm’ con-
gured to ‘reset’ to implement repeve cycles of me which can be
counted by special funcon ‘B.2’ (see secon 1.12.2).
Flash
Several opons allow to congure the display ash in case of ‘stop’
or ‘start’ counng, or in case of alarm acvaon (see secon 1.12.4).
Security on start-up
The ‘On power-up’ funcon denes a me of inacvity of the instru-
ment aer power-up, the status of the instrument (‘start’ or ‘stop’)
aer power-up, and the opon to apply a reset aer power-up (see
secon 1.12.2).
Memory
The instrument saves and recovers the last reading value in case of
power-loss.
Congurable ‘fast-acess’ menu
The front key ‘UP’ () gives access to a user congurable menu with
direct access to several useful funcons such as alarm setpoints and/
or preset value (see secon 1.12.5).
Control and retransmission opons
Opons for output and control with 1, 2 and 3 relays, transistor out-
puts, controls for SSR relays, isolated analog outputs, communica-
ons in Modbus RTU, RS-485 ASCII and RS-232. Special opons with
4 and 6 relay outputs.
Mechanical
Front protecon IP65. Connecons by plug-in screw terminals. For
industrial applicaons.
1.1 How to order
K40 CR
Model Power
-
Opon 1 Others
H
- - -
Opon 2
-
Opon 3
-
-R1 (1 relay)
-AO (analog output)
-RTU (Modbus RTU)
-S4 (RS-485)
-S2 (RS-232)
-T1 (1 transistor)
-SSR (1 control SSR)
- (empty)
-H (85-265 Vac/dc)
-L (11/60 Vdc,
24 Vac, 48 Vac)
-NBT (no buons)
-65 (front IP65)
-G (green led)

FEMA ELECTRÓNICA . Series K . K40-CR
3
Index
1. Panel meter K40-CR . . . . . . . . . . . . . . . . . . . . . . 2
1.1 How to order . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Included funcons . . . . . . . . . . . . . . . . . . . . . 4
1.3 Power connecons . . . . . . . . . . . . . . . . . . . . . 4
1.4 Front view . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.6 Control connecons . . . . . . . . . . . . . . . . . . . . 5
1.7 Types of reset . . . . . . . . . . . . . . . . . . . . . . . . 5
1.8 Technical specicaons . . . . . . . . . . . . . . . . . . 6
1.9 Mechanical dimensions (mm) . . . . . . . . . . . . . . . 6
1.10 How to operate the menus. . . . . . . . . . . . . . . . 7
1.11 Messages and errors . . . . . . . . . . . . . . . . . . . 7
1.12 Conguraon menu. . . . . . . . . . . . . . . . . . . . 8
1.12.1 Inial set-up . . . . . . . . . . . . . . . . . . . . . . 8
1.12.2 Conguraon . . . . . . . . . . . . . . . . . . . . . 8
1.12.3 Controls conguraon . . . . . . . . . . . . . . . . 10
1.12.4 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.12.5 Fast access . . . . . . . . . . . . . . . . . . . . . . .12
1.12.6 Super fast access . . . . . . . . . . . . . . . . . . . 13
1.12.7 Menu ‘Key LE’ . . . . . . . . . . . . . . . . . . . . .13
1.12.8 Le zeros . . . . . . . . . . . . . . . . . . . . . . . . 13
1.12.9 Funcon ‘Password’ . . . . . . . . . . . . . . . . . . 13
1.12.10 Factory reset . . . . . . . . . . . . . . . . . . . . .13
1.12.11 Firmware version. . . . . . . . . . . . . . . . . . . 13
1.12.12 Brightness . . . . . . . . . . . . . . . . . . . . . . 13
1.12.13 Access to oponal modules . . . . . . . . . . . . . 13
1.13 Full conguraon menu . . . . . . . . . . . . . . . . . 14
1.14 Factory conguraon . . . . . . . . . . . . . . . . . . .16
1.15 Applicaon example 1 . . . . . . . . . . . . . . . . . . 17
1.16 Applicaon example 2 . . . . . . . . . . . . . . . . . . 17
1.17 To access the instrument . . . . . . . . . . . . . . . . .18
1.18 Modular system . . . . . . . . . . . . . . . . . . . . . .18
1.19 Precauons on installaon . . . . . . . . . . . . . . . .19
1.20 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.21 CE declaraon of conformity . . . . . . . . . . . . . . . 19
2. Output and control modules . . . . . . . . . . . . . . . . . 20
2.1 Module R1. . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.2 Module T1. . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3 Module SSR . . . . . . . . . . . . . . . . . . . . . . . . .21
2.4 Module AO . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.6 Module RTU. . . . . . . . . . . . . . . . . . . . . . . . . 22
2.5 Module S4. . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.7 Module S2. . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.8 Modules R2, R4, R6. . . . . . . . . . . . . . . . . . . . . 23
3. Other opons . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.1 Opon NBT . . . . . . . . . . . . . . . . . . . . . . . . . 24
4. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .25
4.1 THM benchtop housing . . . . . . . . . . . . . . . . . . 25
4.2 Adapter DRA-M . . . . . . . . . . . . . . . . . . . . . . . 25
4.3 Adapter KA96 . . . . . . . . . . . . . . . . . . . . . . . .25
4.4 WME housing . . . . . . . . . . . . . . . . . . . . . . . . 25
4.5 Protector KIP . . . . . . . . . . . . . . . . . . . . . . . . 25

FEMA ELECTRÓNICA . Series K . K40-CR
4
1.2 Included funcons
Funcons included Secon
Fast access yes, congurable 1.12.5
Preset yes, congurable 1.12.1
Reset
yes, congurable : front,
rear and/or linked to
alarm acvaon
1.7
Counng direcon up or down 1.12.1
Memory yes, recovers at power-up
Funcons ‘on alarm’ yes 1.12.4
Special funcons
control up / down
cycle counter
accumulated counter
exceeded counter
hold control
memory for ‘shorter cycle’
and ‘longer cycle’
1.12.2
‘On Power Up’ yes 1.12.2
Password blocks conguraon 1.12.9
Alarms
acvaon delay
deacvaon delay
inverted relay
locked deacvaon
1.12.4
Display brightness 5 levels 1.12.12
Table 1 - Funcons included
Earth connecon - Although a
terminal is provided for earth
connecon, this connecon is
oponal. The instrument does
not need earth connecon for
correct operaon nor for com-
pliance with the security regu-
laons. ~
~+
-
8 9 0
Fuse - To comply with security regulaon 61010-1, add to the power
line a protecon fuse acng as disconnecon element, easily acces-
sible to the operator and idened as a protecon device.
Power ‘H’ fuse 250 mA me lag
Power ‘L’ fuse 400 mA me lag
1.3 Power connecons
Buon ‘LE’
1.4 Front view
Buon ‘UP’
Logo
Alarms
Units
Buon ‘SQ’
‘Conguraon menu’
(see secon 1.12)
‘Fast access‘
(see secon 1.12.5)
Front reset
(see secon 1.12.7)
Controls
(see secon 1.6)
Opon 1 Opon 2Opon 3
Power
(see secon 1.3)
Detail of the plug-in screw terminals provided with
the instrument. The instrument is provided with all
terminals needed, both male and female.
1.5 Rear view
Control led*
* The ‘led control’ is operave only in counng modes that do not
display seconds or tenths of second. It ashes ‘on’ and ‘o’ at a rate
of 1 second when instrument is counng (‘start’). It remains ‘o’
when the instrument is not counng (’stop’).
12345 890

FEMA ELECTRÓNICA . Series K . K40-CR
5
1.6 Control connecons
Vexc.
12345
Stop
Reset
0 V
Start
• Normal connecons (‘con.a’) - controls for ‘start’, ‘stop’ and ‘re-
set’ are independent. Acvaon by default is by falling edge (by
short-circuit to the 0 Vdc terminal). Internal pull-up resistors are
acvated. This is the normal working mode.
To work with other control signals or acvaons, congure the in-
ternal pull-up / pull-down resistors, the trigger level and the acva-
on by rising or falling edge (see secon 1.12.3).
Vexc.
12345
funcon ‘B’
Reset
0 V
Start / Stop
• Alternave connecons (‘con.b’) - the ‘start’ and ‘stop’ controls
share the same terminal ‘1’. Terminal ‘1’ at high level acvates the
‘start’. Terminal ‘1’ at low level acvates the ‘stop’. The ‘reset’ con-
trol is independent at terminal 5. Terminal ‘3’ is now dedicated to
acvate signal ‘B’. See secon 1.12.2 for more informaon on func-
ons associated to the acvaon of the ‘B’ signal. Acvang on
the conguraon menu a ‘B’ funcon, automacally acvates the
‘alternave connecons’ mode.
The reset funcon can be acvated from three independent and con-
gurable sources:
• Front reset - associated to the front buon ‘LE’ (3). This reset can
be disabled by menu (see secon 1.12.7). The front reset is acvated
by levels (pressed / not pressed).
• Rear reset - connected to pin 5 at the rear terminal. It acvates
by default on falling edge, by connecon to the 0 Vdc terminal. Ac-
vaon is congurable (see secon 1.12.2) by edge (falling or rising)
or level (up or down). Trigger level is congurable between 0 and
3.9 Vdc. Internal congurable pull-up / pull-down resistors allow to
use other type of sensors (NPN, PNP, push-pull, inducves, TTL, ...).
• Alarm reset - alarms 1, 2 and 3 can be congured to acvate a
certain funcon (a reset for example) when alarm acvates (see sec-
on 1.12.4). This conguraon creates innite loops which can be
counted by using funcon ‘B.2 cycles’ (see secon 1.12.2).
1.7 Types of reset
Reading
Minutes
Setpoint 1
Chronometer with ‘reset’ acvaon when read-
ing reaches setpoint 1 (‘15.00’ minutos)
Minutes
Cycle counter
01
2
15.00
0.00
15.00 30.00 45.00

FEMA ELECTRÓNICA . Series K . K40-CR
6
1.9 Mechanical dimensions (mm)
1.8 Technical specicaons
Digits
number of digits 4
led 7 segments led
color red
digit height 20 mm
Reading modes
* Meaning : (d=days, h=hours, m=minutes, s=seconds, c=cents of second)
Sexagesimal reading modes
mm.ss
hh.mm
dd.hh
Decimal reading modes
ssss mmmm hhhh
sss.s mmm.m hhh.h
ss.ss mm.mm hh.hh
maximum reading 99.59 / 99.23 / 9999
minimum reading -19.59 / -19.23 / -1999
Accuracy of the quartz ±0.01 %
Thermal dri 20 ppm / ºC
Controls start, stop, reset
default signal free potenal contact
congurable for ... NPN, PNP, Namur, pick-up, TTL, induc-
ve, mechanical, ...
maximum Vdc on terminals ±30 Vdc
excitaon voltage congurable
+18 Vdc, +15 Vdc, +9 Vdc, +5 Vdc
maximum current 70 mA
protecon yes, current limited to 70 mA
Display refresj 12 refresh/ second
retenon memory yes, recovers counng value in case of
power-loss
Power
power ‘H’ 85 to 265 Vac/dc
power ‘L’ 11 to 60 Vdc and 24/48 Vac
isolaon* 2500 Ve with power‘H’
1500 Ve with power ‘L’
*tested during 60 seconds.
consumpon <1.5 W only meter
<4.0 W meter with opons
Conguraon 3 buons front keypad
Front protecon IP65
Output and control opons relays, analog outputs, serial communi-
caons (see secon 2)
Mechanical
mounng panel
connecons plug-in screw terminal
housing material ABS, polycarbonate (V0)
weight <150 grams
front size 96 x 48 mm (1/8 DIN)
panel cut-out 92 x 44 mm
depth from panel 91 mm (including terminals)
Temperature
operaon from 0 to +50 ºC
storage from -20 to +70 ºC
warm-up me 15 minutes
44
92
Panel
cut-out
16 8
75
96
48

FEMA ELECTRÓNICA . Series K . K40-CR
7
The instrument has two menus accessible to the user :
‘Conguraon menu’ (key SQ) (<)
‘Fast access’ menu (key UP) (5)
Conguraon menu
The ‘conguraon menu’ modies the conguraon parameters to
adapt the instrument to the applicaon needs. To access the ‘con-
guraon menu’ press for 1 second the SQ (<) key. This access can
be blocked by acvang the ‘Password’ (‘PASS’) funcon. While
operang the ‘conguraon menu’, the alarm status is ‘hold’ to the
status they had before accessing the menu, and the output and con-
trol modules remain in ‘error’ state. When leaving the ‘conguraon
menu’, the instrument applies a system reset, followed by a brief
disconnecon of the alarms and the output and control modules.
Funconality is then recovered.
For a detailed explanaon on the ‘conguraon menu’ see secon
1.12, and for a full view of the ‘conguraon menu’ structure see
secon 1.13.
‘Fast access’ menu
The ‘fast access’ menu is an operator congurable menu, providing
fast and direct access to the most usual funcons of the instrument
with a single key pad stroke. Press key UP (5) to access this menu.
See secon 1.12.5 for a list of funcons eligible for ‘fast access’ in
this instrument. The ‘Password’ (‘PASS’) funcon does not block ac-
cess to this menu. Accessing and modifying parameters in the ‘fast
access’ menu does not interfere with the normal funconality of the
instrument, and it does not generate any system reset when validat-
ing the changes.
Front key pad descripon
Key SQ (<) - press the SQ (<) key for 1 second to access the ‘con-
guraon menu’. Inside the menu, the SQ (<) key funcons as a
‘ENTER’ key. It selects and accesses the menu opon currently dis-
played. At menus with numerical value entries, it validates the num-
ber displayed.
Key UP (5) - the UP (5) key gives access to the ‘fast access’ menu.
Inside the menus, it moves vercally through the dierent menu op-
ons. At menus with numerical value entries, it modies the digit
selected by increasing its value to 0, 1, 2, 3, 4, 5, 6, 7, 8, 9.
Key LE (3) - inside the menus, the LE (3) key funcons as the ‘ES-
CAPE’ key. It leaves the selected menu, and eventually, will leave the
whole menu. When leaving the ‘conguraon menu’ with the LE (3)
key, the changed parameters are acvated. At menus with numeri-
cal value entries, the LE (3) key allows to select the acve digit. To
modify the value of the selected digit use the UP (5) key.
Menu ‘rollback’
Aer 30 seconds without interacon from the operator, the instru-
ment will rollback and leave the ‘conguraon menu’ or the ‘fast ac-
cess’ menu. All changes will be discarded.
1.10 How to operate the menus
Example of operaon inside the
‘conguraon menu’.
1. The SQ (<) key enters into the
‘conguraon menu’.
2. The SQ (<) key enters into the
‘Func’ opon menu.
3. The UP (5) key moves through
the menu opons.
4. The SQ (<) key selects the
desired range and returns to the
‘Func’ menu.
5. The LE (3) key leaves the ac-
tual menu level and moves to the
previous menu level.
6. The LE (3) key leaves the ‘con-
guraon menu’. Changes are ap-
plied and saved at this moment.
Funcon
mode
(2)
(3)
(3)
(3)
(3)
(4)
(4)
(4)
(5)
(5)
(5)
(3)
(3)
(6)
(6)
(1)
Messages and errors
‘Err.1’ incorrect password.
‘Err.2’ at ‘oPt.X’ menu entry. Installed module is not recognized.
‘Err.8’ excitaon voltage overload.
‘9999’ + ashing mode. Reading is in overrange.
‘-1999’ + ashing mode. Reading is in underrange.
Table 2 - Messages and error codes
The error messages are shown on display in ash mode.
1.11 Messages and errors

FEMA ELECTRÓNICA . Series K . K40-CR
8
Press ‘SQ’ (<) for 1 second to access the ‘conguraon menu’.
For a descripon on how to operate inside the menus see secon
1.10. For a full vision of the ‘conguraon menu’ structure see
secon 1.13.
To congure the inial set up of the instrument, select the viewing
format, congure the up or down counng mode and assign the pre-
set value.
Enter the ‘Funcon mode’ (‘Func’) menu and select the ‘View’ for-
mat desired.
• ‘MM.SS’ - clock format, minutes and seconds.
• ‘hh.MM’ - clock format, hours and minutes.
• ‘dd.hh’ - clock format, days and hours.
• ‘SSSS’ - counter of seconds.
• ‘SSS.S’ - counter of seconds with one decimal.
• ‘SS.SS’ - counter of seconds with two decimals.
• ‘MMMM’ - counter of minutes.
• ‘MMM.M’ - counter of minutes with one decimal.
• ‘MM.MM’ - counter of minutes with two decimal.
• ‘hhhh’ - counter of hours.
• ‘hhh.h’ - counter of hours with one decimal.
• ‘hh.hh’ - counter of hours with two decimal.
Access the ‘Counng direcon’ (‘dIr’) and select ‘uP’ for up counng
or ‘doWn’ for down counng.
At the ‘Preset’ (‘PrSt’) menu select the preset value. The preset value
will load on display when reset funcon acvates. See secon 1.7 for
a descripon on the dierent acvaon modes for the reset.
Addional conguraon parameters for the instrument.
The ‘On Power Up’ (‘on.Pu’) menu congures funcons to apply at
start-up. It applies only to instrument restart aer power loss. It does
not apply to instrument restart due to change in conguraon.
• parameter ‘Delay’ (‘dLAy’) assigns a waing me in seconds. The in-
strument waits the congured me before starng normal funcon.
During this waing me, the display shows all decimal points on in
ash mode, all alarms are in ‘oFF’ state, there is no signal acquision
and there is no communicaons or control being performed. Aer
the congured me is over, the instrument starts in normal funcon.
Applicaon - the start-up process for an automaon system implies
that dierent parts of the system (engines, actuators, controllers, ...)
have dierent start-up mes. The ‘Delay’ funcon gives me to the
instrument to wait unl the slowest part of the system is fully func-
onal before execung acons on the system (signal reading, relay
acvaon, ...).
• the ‘Reset’ (‘rSt’) parameter will execute a reset of the counter
each me the instrument is restarted.
1.12.2 Conguraon
1.12 Conguraon menu
1.12.1 Inial set-up
Funcon
mode
Preset
Preset value
-1999 to 9999
Counng
direcon
Up
Down
View format
Conguraon On power-up Delay Seconds
Reset
State
0 to 9999
0.0 to 999.9
0.00 to 99.99
0 to 9999
0.0 to 999.9
0.00 to 99.99
0 to 9999
0.0 to 999.9
0.00 to 99.99
0.00 to 99.59
0.00 to 99.59
0.00 to 99.23

FEMA ELECTRÓNICA . Series K . K40-CR
9
• the ‘State’ (‘StAt’) parameter controls the state of the counter aer
power-up. Select ‘Strt’ to count aer power-up or ‘StoP’ to remain
stopped aer power-up.
The whole power-up process of the instrument is explained as fol-
lows : instrument waits the me dened at ‘Delay’, it then resets (or
not) the counter according to parameter ‘Reset’, then it counts or
remains stopped according to parameter ‘StAt’ and then it checks for
external controls ‘start’, ‘stop’ and ‘reset’.
The ‘Flash’ menu (‘FLSh’) controls the acvaon of the rear reset by
edge (‘EdGE’) or by level (‘LEVL’).
The ‘Rear reset’ menu (‘r.rSt’) controls the acvaon of the display
ashing when instrument is stopped (‘StP.F’) and / or when instru-
ment is counng (‘StP.F’).
The ‘Funcon on channel ‘B’’ menu (‘Fn.b’) controls the acvaon
of special funcons on channel ‘B’ (rear terminal 4). If a ‘B’ funcon
is selected, signal connecons change to ‘alternave connecons’ as
indicated at secon 1.6.
Following is an explanaon for each of the 6 ‘B funcons’ available.
• funcon ‘B.1 control up / down’ (‘Fn.b.1’) controls the up or down
counng based on the state of input signal at channel ‘B’.
• funcon ‘B.2 cycles’ (‘Fn.b.2’) enables an internal counter (from 0
to 9999) which can be made visible on display by acvaon of chan-
nel ‘B’ signal. There are several events that can add ‘+1’ to this inter-
nal counter :
• ‘on alarm 1’ (‘o.AL1’) select ‘on’ to add ‘+1’ each me alarm
1 acvates.
• ‘on alarm 2’ (‘o.AL2’) select ‘on’ to add ‘+1’ each me alarm
2 acvates.
• ‘on alarm 3’ (‘o.AL3’) select ‘on’ to add ‘+1’ each me alarm
3 acvates.
• ‘on reset’ (‘o.rSt’) select ‘on’ to add ‘+1’ each me reset
funcon acvates.
• funcon ‘B.3 accumulated’ (‘Fn.b.3’) enables an internal counter
which can be made visible on display by acvaon of channel ‘B’
signal. To reset the accumulated counter, view the counter on dis-
play and acvate the reset (front or rear). The accumulated counter
counts the totalized me that the instrument has been counng or
stopped (needs to be powered-up).
• parameter ‘Format’ (‘ForM’) congures the view format for
the accumulated counter. Value ‘ch.A’ views in same format
as the main instrument.
• at parameter ‘Count’ (‘cnt’) select ‘ALWS’ to count the total
me that the instrument has been powered. Select ‘Strt’ to
count the total me the instrument has been counng. Se-
lect ‘StoP’ to count the total me the instrument has been
stopped.
1.12 Conguraon menu (cont.)
Flash ‘Flash on stop’
‘Flash on start’
Rear reset
acvates by edge
acvates by level
Funcon
on channel ‘B’
Funcon assigned to
channel ‘B’. Select-
ing a ‘B’ funcon
automacally ac-
vates connecon type
‘Con.2’ (see secon
1.6)
Funcon B.1
control up / down
Next menu entry gives access to the conguraon parameters of the ‘chan-
nel ‘B’ funcon’ (‘Fn.b’) previously selected. If no funcon has been selected,
menu entry indicates ‘Fn.b.n’. Following is an explanaon for menus ‘Fn.b.1’
to ‘Fn.b.6’.
Funcon B.2
cycles
‘on alarm 1’
‘on alarm 2’
‘on alarm 3’
on ‘reset’
Funcon B.3
accumulated
Count
Format

FEMA ELECTRÓNICA . Series K . K40-CR
10
1.12 Conguraon menu (cont.)
Funcon B.4
exceeded
‘Start’
Funcon B.5
‘hold’
Funcon B.6
‘Max / min’
Controls
Acvaon for
‘Start’ and ‘Stop’
Pulls for
‘Start’ and ‘Stop’
Pull down
No pull
Pull up
Pulls for reset
Pull down
No pull
Pull up
by rising edge
by falling edge
Acvaon for
‘reset’
by rising edge
by falling edge
• funcon ‘B.4 exceeded’ (‘Fn.b.4’) enables an internal counter for
exceeded me, which can be made visible on display by acvaon of
channel ‘B’ signal. To reset the exceeded counter, view the counter
on display and acvate the reset (front or rear). The reset leaves the
exceeded counter at a value of ‘0’ and in ‘Stop’ mode. The exceeded
counter counts the totalized me aer a certain event triggers the
start of the internal counter.
• at the ‘Start’ (‘Strt’) parameter select ‘o.AL1’ to start the
exceeded counter when alarm 1 acvates. Select ‘o.AL2’ or
‘o.AL3’ to trigger the counter on acvaon of alarm 2 or 3.
• parameter ‘Format’ (‘ForM’) congures the view format for
the exceeded counter. Value ‘ch.A’ views in same format as
the main instrument.
• funcon ‘B.5 hold’ (‘Fn.b.5’) controls the hold of the display by
controlling the state of the signal at channel ‘B’. The chronometer
connues counng on the background.
• funcon ‘B.6 max / min’ (‘Fn.b.6’) internally saves the maximum
and minimum mes recorded of a certain cycle. Each me a reset is
acvated, the instrument compares the actual reading value with the
previous saved memorized values. It replaces the minimum value if
the actual value is smaller. It replaces the maximum value if the actu-
al value is larger. Minimum and maximum values are visible through
front key UP (5) (see secon 1.12.5).
Applicaon - a producon process executes a reset signal each me
a producon element has been nished. At the end of the day, the
maximum and minimum producon mes can be accessed.
1.12.3 Controls conguraon
The ‘Controls’ conguraon menu (‘SnSr’) provides conguraon for
the ‘start’, ‘stop’ and ‘reset’ controls. Default conguraon is acva-
on by free potenal contacts, with acvaon by falling edge (direct
connecon to terminal 0 Vdc). The following parameters allow to
congure the instrument controls to work with other type of signals
(NPN, PNP, inducves, ...).
• ‘Pulls for ‘Start’ and ‘Stop’’ (‘PuL.S’) - select ‘P.uP’ to ac-
vate pull-up resistors (needed for NPN sensors). Select ‘P.dn’
to acvate pull-down resistors (needed for PNP sensors).
Select ‘no’ to deacvate pulls. Selecng a pull resistors congures
the trigger level to 2,5 Vdc.
• ‘Acvaon for ‘Start’ and ‘Stop’’ (‘Act.S’) - select (‘on_h’) to ac-
vate the ‘Start’ and ‘Stop’ controls by rising edge. Select (‘on_0’) to
acvate by falling edge.
• ‘Pulls for reset’ (‘PuL.r’) - select ‘P.uP’ to acvate pull-
up resistors (needed for NPN sensors). Select ‘P.dn’ to ac-
vate pull-down resistors (needed for NPN sensors).
Select ‘no’ to deacvate pulls. Selecng a pull resistors congures
the trigger level to 2,5 Vdc.
• ‘Acvaon for ‘Reset’’ (‘Act.r’) - select (‘on_h’) to acvate the
‘Reset’ control by rising edge. Select (‘on_0’) to acvate by falling
edge. Addionally, reset signal can be congured to acvate by lev-
els instead of edges (see secon 1.12.2). In case of acvaon by lev-
Format

FEMA ELECTRÓNICA . Series K . K40-CR
11
1.12 Conguraon menu (cont.)
Trigger level
Trigger level (from
0 to 31). Each
level is approx.
0.128 Vdc.
Excitaon
voltage
Anrrebound
Anrrebound lter
(0 to 1000 mSec.)
Alarms
Alarm 1 Alarm mode
Deacvated
Normal
Repeat
Setpoint
Type of alarm
els, value ‘on_h’ acvates the reset on high signal value, and value
‘on_0’ acvates reset on low signal. Front reset acvates always by
state.
• ‘Trigger level’ (‘trIG’) - select the signal voltage level at which the
instrument will consider that the signal has reached the acvaon
level. Selectable from 0 to 31 levels, where each level is approx.
imately 0.128 Vdc. Trigger level is the same for channels ‘start’ and
‘stop’. Reset channel has a xed trigger to 2,5 Vdc. The three leds to
the le of the value reect the state (‘0’ or ‘1’) of control channels
‘Start’, ‘Stop’ and ‘Reset’.
• ‘Excitaon voltage’ (‘V.EXc’) - power provided by the instrument
to power-up the sensors (if needed) used to control the signals
‘start’, ‘stop’ and / or ‘reset’, or to be used as an acve signal (‘1’) for
special connecons. Select the for the excitaon voltage at 5 Vdc,
9 Vdc, 15 Vdc or 18 Vdc. Select ‘no’ to disable the excitaon voltage.
• ‘Anrrebound lter’ (‘rbnd’) - Vlue between 0 mSeconds and
1000 mSeconds. when a signal is received, detecon of addional
signals is inhibited for the me dened in this parameter. Recom-
mended value for a mechanical contact sensor is 100 mSeconds.
Applies to ‘start’, ‘stop’ and ‘reset’ signals.
The ‘Alarms’ (‘ALr’) menu congures the independent acvaon of
up to 3 relay outputs (or transistor or SSR control), installed with the
R1 (or T1 or SSr) oponal modules (see secon 2.1). For outputs up
to 4 and 6 relays, see special modules R2, R4 and R6 at secon 2.6.
The alarm states are indicated in the front display with leds marked
as ‘1’, ‘2’ and ‘3’.To congure an alarm, enter into the alarm menu
(‘ALr1’, ‘ALr2’ or ‘ALr3’) and congure the following parameters :
• parameter ‘Alarm mode’ (‘Mode’) allows to disable the alarm
(‘oFF’) or to select between two working modes :
•in ‘normal’ mode (‘norM‘) the alarm has a setpoint con-
gured, that acvates when the display reading reaches the
setpoint value. It can be congured as a ‘maximum alarm’ or
‘minimum alarm’. Provides conguraon for independent ac-
vaon and deacvaon delays, ash control and acon se-
lecon on acvaon.
• in ‘repeat’ mode (‘rEPt’) the alarm acvates each me that
the chronometer reaches a mulple of the setpoint. Alarm
remains acve during the me indicated at parameter ‘de-
acvaon delay’ (‘dEL.1’). Other parameters on the ‘Alarm’
menu have no eect in this mode. This mode is not funconal
in viewing modes with tenths of second or cents of second.
Applicaon : chronometer in ‘mm.ss’ mode with a’repeat’
alarm and setpoint 1 at ‘15.00’. Alarm acvates ar ‘15.00’,
‘30.00’, ‘45.00’, etc.
• at ‘Alarm type’ (‘TypE’) select the alarm to act as a maximum type
alarm (‘MAX’) or a minimum type alarm (‘MIn’). The maximum type
alarm (or minimum type alarm) acvates when the display value is
higher (or lower) than the setpoint value.
• at ‘Setpoint’ (‘SEt’) enter the value for the alarm acvaon point.
This parameter is eligible for conguraon through the ‘Fast access’
menu (see secon 1.12.5).
1.12.4 Alarms

FEMA ELECTRÓNICA . Series K . K40-CR
12
1.12 Conguraon menu (cont.)
‘On alarm’
Connue
To zero
To preset
Inverted relay
‘Locked alarm’
Stop
‘Alarm ash’
Acvaon delay
Deacvaon
delay
Tools
Key UP
(‘Fast access’)
Memory of
maximum
Memory of
minimum
Setpoint 1
Setpoint 2
Setpoint 3
Memory of
cycles
Preset value
• at ‘Acvaon delay’ (‘dEL.0’) congure the delay to apply before
alarm acvaon. The acvaon delay starts counng when the set-
point value is passed. Value from 0.0 to 99.9 seconds.
• at ‘Deacvaon delay’ (‘dEL.1’) congure the delay to apply
before alarm deacvaon. The deacvaon delay starts counng
when the setpoint value plus the hysteresis value, is passed. Value
from 0.0 to 99.9 seconds.
• the ‘Relay inverted’ (‘r.Inv’) parameter inverts the normal relay
connecons. When set to ‘on’ the relay will be acve when alarm is
inacve. For security applicaons where an inacve relay controls
the shutdown of the system.
• the ‘Locked alarm’ (‘A.Lck’) parameter disables the automac
deacvaon of the alarm. Alarm deacvaon must be performed
manually, by pressing the ‘LE’ front buon (see secon 1.12.7)
• the ‘On alarm’ (‘on.AL’) parameter assigns a predened behavior
when alarm acvates.
• select ‘cont’ to connue counng.
• select ‘to_0’ to load ‘0’ on displays Parameter ‘deacvaon
delay’ (‘dEL.1’) automacally congures to 1 second.
• select ‘to_p’ to load preset value on display. Parameter ‘de-
acvaon delay’ (‘dEL.1’) automacally congures to 1 sec-
ond.
• select ‘stop’ to stop the counng.
• set the ‘Alarm ash’ (‘AL.FL’) parameter to ‘on’ to acvate the
ash of the display when alarm is acve. To manually deacvate the
ash mode, press any of the front keys or change the state of any of
the control signals ‘start’, ‘stop’ or ‘reset’.
The ‘UP’ (5) key at the front of the instrument gives access to a list
of funcons congurable by the operator. See secon 1.10 for an ex-
planaon on how to operate the ‘fast access’ menu.
The ‘Key UP (Fast access)’ (‘K.uP’) menu allows to select which func-
ons will be accessible through the ‘fast access’ menu. Select ‘on’ to
acvate each funcon.
• the ‘Setpoint 1’ (‘ALr1’) funcon allows to visualize and modify the
alarm 1 setpoint through the ‘fast access’ menu.
• the ‘Setpoint 2’ (‘ALr2’) funcon allows to visualize and modify the
alarm 2 setpoint through the ‘fast access’ menu.
• the ‘Setpoint 3’ (‘ALr3’) funcon allows to visualize and modify the
alarm 3 setpoint through the ‘fast access’ menu.
• the ‘Memory of maximum’ (‘MAX’) or ‘Memory of minimum’
(‘MIn’) funcons allow to visualize the maximum or minimum read-
ing value stored in memory. To reset this value, visualize the memory
value at the ‘fast access’ menu with key UP (5) and when message
‘rSt’ is displayed, press (<) to reset.
• the ‘Memory of cycles’ (‘cYcL’) funcon allow to visualize and reset
the memory of cycles. To reset this value, visualize the memory value
at the ‘fast access’ menu with key UP (5) and when message ‘rSt’
is displayed, press (<) to reset. The memory of cycles countes ‘+1’
each me a reset alarm occurs (‘on_AL’ / ‘to_0’ or ‘to_P’) or a reset
by ‘overrange’ / ‘underrange’ occurs.
• the ‘Preset value’ (‘PrSt’) funcon allows to visualize and modify
the preset value congured.
1.12.5 Fast access

FEMA ELECTRÓNICA . Series K . K40-CR
13
1.12 Conguraon menu (cont.)
If only a single funcon is selected for the ‘fast access’ menu, press-
ing the the ‘UP’ (5) key will shortly display the funcon name and
then automacally jump to the funcon value.
1.12.6 Super fast access
Le zeros
With le zeros
Without le zeros
Password
Factory reset
Version
Minimum
Brightness
Maximum
Standard
Opon 1
Conguraon menu for the module installed at Opt.1
Opon 2
Conguraon menu for the module installed at Opt.2
Opon 3
Conguraon menu for the module installed at Opt.3
The ‘LE’ (3) key at the front of the instrument can be congured to
acvate several funcons. Only one funcon can be assigned to the
‘LE’ (3) key
• the ‘No funcon’ (‘nonE’) value assigns no funcon.
• the ‘Reset’ (‘rSt’) value asigns the reset funon to the ‘LE’ (3) key.
• the ‘Reset + Start’ (‘r.Str’) value asigns the reset and start funcon
to the ‘LE’ (3) key.
• the ‘Alarm unlock’ (‘A.Lck’) value assigns the manual unlock of the
alarms funcon, for instruments with the ‘Locked alarms’ (‘A.Lck’)
funcon acvated (see secon 1.12.4)
1.12.7 Menu ‘Key LE’
At the ‘Password’ (‘PASS’) menu select a 4 digit code to block access
to the ‘conguraon menu’. Instrument conguraon will not be ac-
cessible to non authorized personnel. To acvate the ‘Password’ se-
lect ‘on’ and introduce the code.
The code will be requested when trying to access the ‘conguraon
menu’ (key ‘SQ’ (<)). The ‘fast access’ menu is not password pro-
tected.
The ‘Version’ (‘VEr’) menu informs of the current rmware version
installed in the module.
At the ‘Brightness’ (‘LIGh’) menu select the light intensity for the
front leds. With this funcon it is possible to adapt the instrument to
the environment light intensity.
1.12.8 Le zeros
Menus ‘OPt.1’, ‘OPt.2’ and ‘OPt.3’ give access to the ‘conguraon
menus’ of the output and control modules installed at slots Opt.1,
Opt.2 and Opt.3.
See secon 2 for a list of output and control modules available for
each slot. The ‘conguraon menu’ of each module is described at
the User’s Manual of each module.
1.12.9 Funcon ‘Password’
At the ‘Factory reset’ (‘FAct’) menu, select ‘yes’ to load the default
factory conguraon for the instrument (see secon 1.14).
1.12.10 Factory reset
1.12.11 Firmware version
1.12.12 Brightness
The ‘Le zeros’ (‘L.ZEr’) parameter controls the le zeros on or o.
1.12.13 Access to oponal modules
Key LE
Reset
Alarm unlock
No funcon
Reset + Start

FEMA ELECTRÓNICA . Series K . K40-CR
14
1.13 Full conguraon menu
Press ‘SQ’ (<) for 1 second to access the ‘Conguraon menu’. See
secon 1.12 for a descripon of each menu entry.
Funcon
mode
Preset
Preset value
-1999 to 9999
Counng
direcon
Up
Down
Funcon
on channel ‘B’
Funcon assigned to
channel ‘B’. Select-
ing a ‘B’ funcon
automacally ac-
vates connecon type
‘Con.2’ (see secon
1.6)
Funcon B.1
control up / down
Next menu entry gives access to the conguraon parameters of the ‘channel ‘B’
funcon’ (‘Fn.b’) previously selected. If no funcon has been selected, menu entry
indicates ‘Fn.b.n’. Following is an explanaon for menus ‘Fn.b.1’ to ‘Fn.b.6’.
Funcon B.2
cycles
‘on alarm 1’
‘on alarm 2’
‘on alarm 3’
on ‘reset’
Funcon B.3
accumulated
Format
Count
Funcon B.4
exceeded
Format
View format
Conguraon
Flash ‘Flash on stop’
‘Flash on start’
On power-up Delay Seconds
Reset
State
Rear reset
acvates by edge
acvates by level
0 to 9999
0.0 to 999.9
0.00 to 99.99
0 to 9999
0.0 to 999.9
0.00 to 99.99
0 to 9999
0.0 to 999.9
0.00 to 99.99
0.00 to 99.59
0.00 to 99.59
0.00 to 99.23

FEMA ELECTRÓNICA . Series K . K40-CR
15
1.13 Full conguraon menu (cont.)
‘Start’
Funcon B.5
‘hold’
Funcon B.6
‘Max / min’
‘On alarm’
Connue
To zero
To preset
Alarm 1
Setpoint
Alarm mode
Type of alarm
Alarms
Acvaon delay
Deacvaon
delay
Inverted relay
‘Locked alarm’
Disabled
Normal
Repeat
Stop
‘Alarm ash’
Controls
Acvaon for
‘Start’ and ‘Stop’
Pulls for reset
Pulls for
‘Start’ and ‘Stop’
Acvaon for
‘reset’
Pull down
No pull
Pull up
Pull down
No pull
Pull up
by rising edge
by falling edge
by rising edge
by falling edge
Excitaon
voltage
Anrrebound
Anrrebound lter
(0 to 1000 mSec.)
Trigger level
Trigger level (from
0 to 31). Each
level is approx.
0.128 Vdc.

FEMA ELECTRÓNICA . Series K . K40-CR
16
1.13 Full conguraon menu (cont.)
Tools Key UP
(‘Fast access’)
Memory of
maximum
Memory of
minimum
Setpoint 1
Setpoint 2
Setpoint 3
Memory of
cycles
Preset value
Password
Factory reset
Le zeros
With le zeros
Without le zeros
Version
Minimum
Brightness
Maximum
Standard
Opon 2
Conguraon menu for the module installed at Opt.2
Opon 3
Conguraon menu for the module installed at Opt.3
1.14 Factory conguraon
Funcon mode
View format MM.SS
Counng direcon up
Preset 00.00
Conguraon
‘On power-up’
Delay 0 seconds
Reset o
State stopped (‘StoP’)
Flash
‘Flash on stop’ o
‘Flash on start’ o
Rear reset acvates by edges (‘EdGE’)
Funcon on channel ‘B’ no
Controls
Pulls for ‘start’ and ‘stop’ pull-up (‘P.uP’)
Acvaon for ‘start’ and ‘stop’ by falling edge (‘on_0’)
Pulls for reset pull-up (‘P.uP’)
Acvaon for reset by falling edge (‘on_0’)
Trigger level 2.56 Vdc (level 20)
Excitaon voltage 15 Vdc
Anrrebound lter disabled (0 mSeconds)
Alarms 1,2 and 3
Mode o (disabled)
Type of alarm of maximum
Setpoint 0
Acvaon delay 0.0 seconds
Deacvaon delay 0.0 seconds
Inverted relay o
‘Locked alarms’ o
‘On alarm’ connue
‘Alarm ash’ o
Herramientas (‘TooL’)
‘Fast acess’ (
key UP ) o
Setpoint 1 o
Setpoint 2 o
Setpoint 3 o
Memory of maximum o
Memory of minimum o
Cycles o
Preset o
Ley ‘LE’ reset funcon
Le zeros o
Password o
Brightness 3
on
o
Key LE
Reset
Alarm unlock
No funcon
Reset + Start
Opon 1
Conguraon menu for the module installed at Opt.1

FEMA ELECTRÓNICA . Series K . K40-CR
17
In an industrial process of electrolyc bath, the weed parts need
to be removed from the bath and replaced with new parts every 20
minutes. The process of removing and adding parts to the electro-
lyc bath is automated and takes 15 seconds. During these 15 sec-
onds, the system of electrolyc bath should receive no power supply,
which must be reacvated aer 15 seconds, when new items are
immersed in the bath.
The M60-CR chronometer can be congured to acvate a relay out-
put every 20 minutes, and this relay must remain acve for 15 sec-
onds. Aer this me, the relay will deacvate.
Addionally, the system needs the counter to start counng as soon
as power is received, although a 60 seconds delay is needed to give
me to the rst acvaon of the electrolyc bath. Counter must con-
nue counng from the value it had before the power was removed.
Conguraon would be as indicated below :
• View format
‘Func’ / ‘View’ ‘mm.ss’
• Counng direcon
‘Func’ / ‘dIr’up (‘uP’)
• Preset value
‘Func’ / ‘PrSt’ ‘0.00’
• Delay on power-up
‘conF’ / ‘on_Pu’ / ‘dLAY’ 60 seconds
• Inial reset disabled
‘conF’ / ‘on_Pu’ / ‘rSt’ ‘oFF’
• Start counng aer power-up
‘conF’ / ‘on_Pu’ / ‘StAt’ start (‘Strt’)
• Alarm mode
‘ALr’ / ‘ALr1’ / ‘Mode’ repeat (‘rEPt’)
• Alarm every 20 minutes
‘ALr’ / ‘ALr1’ / ‘SEt’ 20.00
• Deacvaon delay
‘ALr’ / ‘ALr1’ / ‘dEL.1’ 15.0 seconds
• On alarm acvaon
‘ALr’ / ‘ALr1’ / ‘on_AL’ connue (‘cont’)
1.15 Applicaon example 1
Alarm 1
Minutes
Chronometer with repeated acvaon of
alarm 1 aer 20 minutes
on
o
20.00 40.00 60.00
15 seconds
60 seconds
00.00
inial
start-up
An industrial process has an oven to dry dierent elements. The dry-
ing me of each element is variable, and the operator requires that
the seng of each drying me to be easily accessible and modiable.
The modicaon of other conguraon parameters must be locked.
During the process, the operator needs two signals. First signal ac-
vates a buzzer which should start 5 minutes before the end of the
scheduled drying me, and remain acve for 15 seconds. The second
signal must acvate at the end of the drying me and must remain
acve unl the operator manually the ‘reset’ signal.
The M60-CR chronometer can be congured for down counng, with
start me at preset value, which will be directly accessible and modi-
able when pressing the front key UP (‘5’). All conguraon pa-
rameters (except the ‘preset’ value) will be password locked. Alarm 1
will acvate for 15 seconds when 5 minutes are missing to end the
process. Alarm 2 will acvate when the scheduled me is over and
will remain acve unl the operator manually resets.
• View format
‘Func’ / ‘View’ ‘hh.mm’
• Counng direcon
‘Func’ / ‘dIr’down (‘doWn’)
• Alarm 1 : alarm mode
‘ALr’ / ‘ALr1’ / ‘Mode’ normal (‘norM’)
• Alarm 1 : type of alarm
‘ALr’ / ‘ALr1’ / ‘tYPE’ minimum (‘MIn’)
• Alarm 1 : acvaon setpoint
‘ALr’ / ‘ALr1’ / ‘SEt’ ‘00.05’
• Alarm 1 : deacvaon delay
‘ALr’ / ‘ALr1’ / ‘dEL.1’ 15.0 seconds
• Alarm 1 : connue counng when alarm acvates
‘ALr’ / ‘ALr1’ / ‘on_AL’ connue (‘cont’)
• Alarm 2 : alarm mode
‘ALr’ / ‘ALr1’ / ‘Mode’ normal (‘norM’)
• Alarm 2 : type of alarm
‘ALr’ / ‘ALr1’ / ‘tYPE’ minimum (‘MIn’)
• Alarm 2 : acvaon setpoint
‘ALr’ / ‘ALr1’ / ‘SEt’ ‘00.00’
• Alarm 1 : when alarm acvates, stop counng
‘ALr’ / ‘ALr1’ / ‘on_AL’ stop (‘stop’)
• Assign the preset value to the ‘UP’ front key
‘TooL’ / ‘K.uP’ / ‘PrSt’ ‘on’
• Conguraon block by password
‘TooL’ / ‘PASS’ / ‘on’ assign the password code
1.16 Applicaon example 2
State of alarm 1
on
o
15 seconds
Reading
me
Example with preset selected at 6 hours
and 30 minutes
‘06.30’
‘00.00
05.25. 05.30
0.00
‘00.05
State of alarm 2
on
o

FEMA ELECTRÓNICA . Series K . K40-CR
18
1.17 To access the instrument
1.18 Modular system
M Series panel meters are designed to create a modular system. This
modular system allows for addion, replacement or substuon of
any of the internal modules conforming the instrument. Below is a
graphic explanaon for the posion of each module.
Risk of electric shock. Removing the front cover will
grant access to the internal circuits. Disconnect the
input signal to prevent electric shock to the operator.
Operation must be performed by qualied personnel
only.
To open the housing, use a at screwdriver to free the xaon clips,
if possible, in the following order : D, C, B and A. Remove the front
cover. Let the inside of the instrument slide out of the housing.
To reinsert the instrument make sure that all modules are correctly
connected to the pins on the display module. Place all the set into
the housing, assuring that the modules correctly t into the internal
guiding slides of the housing. Once introduced, place again the front
cover in front of the housing, placing rst corner ‘X’ and then insert-
ing clips ‘A’, ‘B’, ‘C’ and ‘D’ in this order.
XA
C
BD
Front Filter Display Module Oponal Control Modules
Input Signal Module
Housing
Power Supply Module
Opt.3
Opt.2
Opt.1

FEMA ELECTRÓNICA . Series K . K40-CR
19
This instrument has been designed and veried conforming to the 61010-1
CE Security Regulaon, for industrial applicaons.
Installaon of this instrument must be performed by qualied personnel
only. This manual contains the appropriate informaon for the installaon.
Using the instrument in ways not specied by the manufacturer may lead to
a reducon of the specied protecon level. Disconnect the instrument from
power before starng any maintenance and / or installaon acon.
The instrument does not have a general switch and will start operaon as
soon as power is connected. The instrument does not have protecon fuse,
the fuse must be added during installaon.
The instrument is designed to be panel mounted. An appropriate venlaon
of the instrument must be assured. Do not expose the instrument to excess
of humidity. Maintain clean by using a humid rag and do NOT use abrasive
products such as alcohols, solvents, etc.
General recommendaons for electrical installaons apply, and for proper
funconality we recommend : if possible, install the instrument far from
electrical noise or magnec eld generators such as power relays, electrical
motors, speed variators, ... If possible, do not install along the same conduits
power cables (power, motor controllers, electrovalves, ...) together with sig-
nal and/or control cables.
Before proceeding to the power connecon, verify that the voltage level
available matches the power levels indicated in the label on the instrument.
In case of re, disconnect the instrument from the power line, re alarm
according to local rules, disconnect the air condioning, aack re with car-
bonic snow, never with water.
1.19 Precauons on installaon
Risk of electrical shock. Instrument terminals can be connected
to dangerous voltage.
Instrument protected with double isolaon. No earth connecon
required.
Instrument conforms to CE rules and regulaons.
1.20 Warranty
This instrument is warranted against all manufacturing defects for a
period of 24 MONTHS from the shipment date. This warranty does
not apply in case of misuse, accident or manipulaon by non-autho-
rized personnel. In case of malfuncon get in contact with your local
provider to arrange for repair. Within the warranty period and aer
examinaon by the manufacturer, the unit will be repaired or subs-
tuted when found to be defecve. The scope of this warranty is lim-
ited to the repair cost of the instrument, not being the manufacturer
eligible for responsibility on addional damages or costs.
1.21 CE declaraon of conformity
Manufacturer FEMA ELECTRÓNICA, S.A.
Almira 14 - Pol. Ind. Sanga
E08210 - Barberà del Vallès
BARCELONA - SPAIN
www.fema.es - [e-mail]
Products K40-CR
The manufacturer declares that the instruments indicated comply with the
direcves and rules indicated below.
Electromagnec compability direcve 2014/30/EU
Low voltage direcve 2014/35/EU
Direcve ROHS 2011/65/EU
Security rules EN-61010-1
Instrument Fixed
Permanently connected
Polluon degree 1 and 2 (without condensaon)
Isolaon Double
Electromagnec compability rules EN-61326-1
EM environment Industrial
Immunity levels
EN-61000-4-2 By contact ±4 KV Criteria B
By air ±8 KV Criteria B
EN-61000-4-3 Criteria A
EN-61000-4-4 On AC power lines : ±2 KV Criteria B
On DC power lines : ±2 KV Criteria B
On signal lines : ±1 KV Criteria B
EN-61000-4-5 Between AC power lines ±1 KV Criteria B
Between AC power lines and earth ±2 KV Criteria B
Between DC power lines ±1 KV Criteria B
Between DC power lines and earth ±2 KV Criteria B
Between signal lines and earth ±1 KV Criteria B
EN-61000-4-6 Criteria A
EN-61000-4-8 30 A/m at 50/60 Hz Criteria A
EN-61000-4-11 0 % 1 cycle Criteria A
40 % 10 cycles Criteria A
70 % 25 cycles Criteria B
0 % 250 cycles Criteria B
Emission levels
CISPR 11 Instrument Class A, Group 1 Criteria A
Barberà del Vallès September 2017
Xavier Juncà - Product Manager
According to direcve 2012/19/EU, electronic equip-
ment must be recycled in a selecve and controlled
way at the end of its useful life.

FEMA ELECTRÓNICA . Series K . K40-CR
20
2. Output and control modules
The R1 module provides 1 relay output to to install at digital panel
meters from Series K, up to a maximum of 3 relays in a single meter.
Note : for more than three relays per instrument or larger relay den-
sity per module, see special modules R2, R4 and R6.
Conguraon is performed from the frontal keypad of the meter, by
seng the parameters at the alarm menu. Check the parameters of
at the alarm menu for full informaon.
Relay with 3 contacts (common, normally open, normally closed)
with up to 250 Vac switching voltage and 8 A.
Modules R1 can be ordered pre-installed into a Series K digital panel
meter, or standalone for delayed installaon, as they do not require
soldering or special conguraon.
2.1 Module R1
For more informaon : hp://fema.es/docs/4254_SERIES_M-K-S_
OPTIONS_manual_i.pdf
Type of relay 3 contact relay (NC, NO, common)
Current maximum 8 A per relay (resisve load)
Voltage maximum* 250 Vac connuous
Isolaon 3500 Ve
Type of terminal plug-in screw terminal, pitch 5.08 mm
Slots allowed ‘Opt.1’, ‘Opt.2’, ‘Opt.3’
Terminal A Common
Terminal B NO - Normally open
Terminal C NC - Normally closed
Power
Opt.2
Opt.1
Opt.3
A B C
A B C
Signal
A B C
The T1 module provides 1 transistor output to install at digital panel
meters from Series K, up to a maximum of 3 transistors in a single
meter.
Conguraon is performed from the frontal keypad of the meter, by
seng the parameters at the alarm menu. Check the parameters of
at the alarm menu for full informaon.
Transistor output is optoisolated, provides 2 terminals for connec-
on, and can switch up to 35 V and 50 mA.
Modules T1 can be ordered pre-installed into a Series K digital panel
meter, or standalone for delayed installaon, as they do not require
soldering or special conguraon.
2.2 Module T1
For more informaon : hp://fema.es/docs/4254_SERIES_M-K-S_
OPTIONS_manual_i.pdf
Type of output transistor
Max. voltage 35 Vdc
Max. current 50 mA
Isolaon 3500 Ve
Type of terminal plug-in screw terminal, pitch 5.08 mm
Slots allowed ‘Opt.1’, ‘Opt.2’, ‘Opt.3’
‘B’
‘A’
Schemac for T1 output
Power
Opt.2
Opt.1
Opt.3
A B C
A B C
Signal
A B C