FERREX FPHS 3.6V User manual

1
User Manual
3.6 V
Pivot Handle Screwdriver
FPHS 3.6V
ORIGINAL INSTRUCTIONS
Spend a little Live a lot.
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 1

2
1
2
3
6
4
5
13
11
12
7
8
9
10
14
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 2

3
Package contents/device parts
1 LED charging level display
2 Button for LED charging status
3 Handle swivel lock
4 Switch for left/right rotation and trigger lock
5 On/ Off switch
6 Charging socket
7 LED working light
8 Torque pre-selection with marking
9 Tool holder ¼" = 6.35 mm
10 Torque scale
11 Battery charger
12 Charging connector
13 Bit set
14 Magnetic bit holder
15 Storage case (not shown)
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 3

Table of contents
Package contents/device parts 3
General information 6
Key to symbols 6
Safety 8
Proper use 8
Residual risks 11
General safety information for power tools 11
Safety information for battery chargers 19
Before use 24
Checking the product and scope of delivery 24
Charging the battery 24
Displaying the charging level 25
Use as a pivot handle screwdriver/
angled or straight 26
Fitting screwdriver bits 27
Use 27
Switching on and off 27
Left/right rotation, trigger lock 28
Setting the torque 28
Operating information 29
4
Table of contents
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 4

5
Table of contents
Maintenance, cleaning and storage 30
Maintenance 30
Cleaning 30
Storage 31
Faults and troubleshooting 31
Technical data 32
Disposal 35
Disposing of used tools 35
Batteries and battery packs 36
Disposing of packaging 36
Service information 37
CE declaration of conformity 39
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 5

6
General information
General information
Reading and storing the user manual
This user manual accompanies this 3.6 V
Li-Ion screwdriver (referred to below only as
the “screwdriver”). It contains important
information about start-up and handling.
Before using the screwdriver, read the user manual
carefully. This particularly applies to the safety
instructions. Failure to heed this user manual may result
in severe injury or damage to the screwdriver.
Store the user manual for future use. If you pass the
cordless screwdriver on to third parties, please be
absolutely sure to include this user manual.
Explanation of symbols
The following symbols and signal words are used in this
user manual, on the screwdriver or on the packaging.
This signal symbol/word designates a hazard with
moderate degree of risk which may lead to death or
severe injury if not avoided.
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 6

7
General information
This signal symbol/word designates a hazard with low
risk that, if not avoided, may result in minor or moderate
injury.
This signal word warns against potential damages to
property.
This symbol provides you with useful
additional information about start-up or
operation.
Declaration of conformity (see chapter
“Declaration of conformity”): Products
marked with this symbol meet all applicable
Community regulations for the European
Economic Area.
This symbol indicates that this product may
not be disposed of in the household waste in
accordance with the Waste Electrical and
Electronic Equipment Directive and national
laws.
This symbol identifies devices that are
operated with direct current.
CAUTION!
NOTICE!
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 7

8
Safety
This symbol identifies double insulated
electric devices.
This symbol shows the polarity of the device.
Products marked with this symbol may only
be operated in indoor areas.
Read the user manual before use.
Important! Read the user manual for the
charger.
Safety
Proper use
The screwdriver is only designed for light screw
driving.
The screwdriver has not been designed for commercial
use, use in the trades or for industrial applications; it is
only designed for private use in hobby and DIY
projects.
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 8

9
Safety
The screwdriver may only be used in line with its
intended purpose. Any other kind of use is prohibited.
Proper use also includes compliance with the safety
instructions and operating notes in the user manual.
The manufacturer or vendor accepts no liability for
damage caused by improper or incorrect use.
Only accessories that are suitable for the screwdriver
may be used.
Those using the screwdriver and performing
maintenance work must be familiar with it and have
undergone instruction on the potential risks.
Furthermore, every aspect of applicable accident
prevention guidelines must be exactly adhered to.
Other general guidelines relating to occupational
medicine and safety must be observed. Modifications
to the screwdriver rule out any liability of the
manufacturer and resulting damage.
Any other applications are expressly prohibited and
are deemed improper use.
• Using the screwdriver for other than the intended
purposes;
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 9

10
Safety
• Failure to observe the safety instructions and
warnings as well as the assembly, operating,
maintenance and cleaning instructions contained in
this user manual;
• Failure to comply with any regulations relating to
accident prevention, occupational medicine or
safety, which specifically and/or generally apply to
the use of the screwdriver;
• Use of accessories and spare parts not intended for
the screwdriver;
• Modifications to the screwdriver;
• Repairs of the screwdriver performed by parties
other than the manufacturer or a qualified
professional;
• use of the screwdriver for commercial or industrial
applications as well as in connection with the trades;
• operation or maintenance of the screwdriver by
persons not familiar with how to handle the
screwdriver and/or who are not aware of the related
risks.
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 10

11
Safety
Residual risks
Despite proper use, inconspicuous residual risks
cannot be completely ruled out.
The following risks may arise due to the nature of the
screwdriver:
• Injury to health attributed to vibration emissions if
the device is used over a prolonged period of time
or is not guided and maintained properly,
• Injury and damage to property caused by projected
parts or tool adapters that break during use.
Safety instructions
General power tool safety warnings
WARNING! Read all the safety warnings,
instructions, illustrations and specifications
supplied with this power tool.
Failure to follow all instructions listed below may result
in an electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 11

12
Safety
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
Work area safety
a) Keep your work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 12

13
Safety
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges and
moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use only
extension cords that are suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power
tools may result in serious personal injury.
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 13

14
Safety
b) Use personal protective equipment. Always wear
eye protection.
Protective equipment such as dust
masks, non-slip safety shoes, hard hats, or ear
protection used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to
power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your
finger on the switch or energising power tools while
the switch is set to “on” may lead to accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 14

15
Safety
are connected and properly used.
Use of dust
collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of
tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories or storing the power tool.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children. Do not allow persons unfamiliar with
the power tool or these instructions to operate
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 15

16
Safety
this power tool.
Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions. taking into
account the working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe
handling and control of the tool in unexpected
situations.
i) Hold power tool by insulated gripping surfaces,
when performing an operation where the
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 16

fastener may contact hidden wiring or its own
cord. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects
that can make a connection from one terminal to
another.
Shorting the battery terminals together
may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
17
Safety
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 17

e) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire,
explosion or risk of injury.
f) Do not expose a battery pack or tool to fire or
excessively high temperatures. Exposure to fire or
temperatures above 130 °C may cause an
explosion.
g) Carefully follow all instructions for charging the
battery and never charge the battery or cordless
tool outside of the temperature range indicated
in the instructions. Improper charging or charging
outside of the specified temperature range may
damage the battery and increase the risk of fire.
Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
18
Safety
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 18

19
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 19
Safety instructions for chargers
The charger may be used by children from the age
of 8 and also by persons with reduced physical,
sensory or mental capabilities or lack of experience
and/or knowledge, only if they are supervised or
have been instructed on the safe operation of the
equipment and understanding the risks resulting
from this.
− Ensure that children do not play with the device.
− Cleaning and user maintenance must not be
carried out by children without supervision.
− If the mains connection line of this device is
damaged, only have it replaced by the
manufacturer or its After Sales Support or a similar
qualified person to avoid risks.
− Do not charge any non-rechargeable batteries.
Failure to heed this notice will result in risks.
Safety

Proper use of the charger
Improper use of the charger could result in
risks and damages. Therefore, carefully
read through the following notes.
a) Before using the charger, read through all
instructions and all precautionary measures for the
charger and rechargeable battery. You can find
notes in these instructions and on the device itself
amongst others.
b) Check the charger regularly for damages,
particularly the connector cable and housing. A
damaged charger may only be used again after it
was repaired.
c) Do not use the charger if it has been exposed to
impacts or shocks or if it has fallen down or has
been otherwise damaged. Please bring the
charger to an authorised technical after sales
support for repair or inspection.
d) Never connect a rechargeable battery that has
burst or been otherwise damaged with the
charger. Otherwise there is a risk of electric shock.
e) Do not in any case dismantle the charger. Repairs
may only be performed by an authorised technical
20
Safety
FX-5902193-94-Bedien-1902 04.04.19 11:50 Seite 20