FEZIBO FZ-SM03PS-1 User manual

FZ-SM03PS-1
Single monitor Arm
Scan the QR code with your mobile device or follow the link for
helpful videos and specifications related to this product.
https://www.facebook.com/Fezibous/

Safety
Hazard Symbols Review:
These symbols alert users of a safety condition that demands attention. All users should be able
to recognize and understand the significance of the following Safety Hazards if encountered on
the product or within the documentation. Children who are not able to recognize and respond
appropriately to Safety Alerts should not use this product without adult supervision!
Important! You will need to adjust this product after installation is complete. Make
sure all your equipment is properl y installed on the product before attempting
adjustments. This product should move smoothly and eaily through the full range of
motion and sty where you set it. If movements are too easy or difficult or if product
does not stay in desi red positions, follow the adjustment instructions to create
smooth and easy movements. Depending on your product and the adjustment, it may
take many turns to notice a difference. Any time equipment is added or removed from
thi s product, resulting in a change in the weight of the mounted load, you should
repeat these adjustment steps to ensu re safe and optimum operation.
Warning: Because mounting surface materials can vary widely, it is imperative that you
make sure mounting surface is strong enough to handle mounted product and
equipment
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing
instructions in this manual. Failure to follow these instructions may result in
equipment damage or personal injury.
Symbol Signal Word
NOTE A NOTE indicates important information that helps
you make be? er use of this product.
A WARNING indicates either potential for property
damage, personal injury, or death.
An Electrical indicates an impending electrical
hazard which, if not avoided, may result in
personal injury, fireand/or death.
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid
the problem.
CAUTION
WARNING
ELECTRICAL
Level of Hazard

Features & Specifi cations
Components Tools Needed
CAUTION: DO NOT EXCEED
MAXIMUM LISTED WEIGHT
CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
7 - lbs
(3.2 - kg)
280°
360°
180°
5°
70°
BA C D
1
2
3
4
1x 1x
1x
1x
2x
2x
1x
x
1x1x
4mm
8x
2.5mm
1x 1x
1x
1x
1x
2x x
M4x12mm (x4)
M-A
Screws
M4x16mm (x4)
M-B
Screws
M5x12mm (x4)
M-C
Screws
M5x16mm (x4)
M-D
Screws
D5 (x4)
M-E
Washer
M-F (x4)
M-F
Washer
min10~max85mm
75mm
100mm
114mm
75mm
100mm
114mm
min220~max275mm
185mm
47mm
mm58xam~01nim
mm001
±90°
mm813
Ø35mm
±180°
±135°
max280mm
min90~max575mm
60mm
±180°
+45°
-45°

STEP 1 A ttach P ole t o the Base
STEP 2 Choose a mounting option
Attach pole (B) onto base (C) of monitor stand with bolts (Q)
using provided 4mm Allen wrench (R).
B
C
Q
R
E P
R
OPTION A: Clamp Installation
Install clamp base support (E) onto base of monitor stand with bolts (P)
using provided 4mm Allen wrench (R).

J
Secure clamp (F) to upper two holes with
bolts (O) using 4mm Allen wrench (R) for
desks with a thickness of 10-55mm.
Secure clamp (F) to lower two holes with
bolts (O) using 4mm Allen wrench (R) for
desks with a thickness of 50-85mm.
Apply pads (J) to bottom of base to prevent table top from being scratched.
10-55mm
O
R
F F
50-85mm
O
R
Adjust the Mount to the Desktop
Thickness 10-55mm
Adjust the Mount to the Desktop
Thickness 50-85mm

STEP 2 (Continued)
OPTION B: Grommet Base Installation
I
H
P
R
J
G
Attach base support cover (G) to clamp base support (E). Tighten the clamp to the
desktop using the plastic knob.
Slide long screw (H) through the top of the grommet base support (I) and install on base of
monitor stand with bolts using 4mm Allen wrench (R). Apply pads (J) to bottom of base.

A
S
STEP 3 Assemble the Arm
K
M
LU
Position stand on desk with long screw through hole, and secure by using the support plate (K)
and washer (M) on underside of the mounting surface, tighten the nut (L) with wrench (U).
Attach arm assembly (A) onto the pole and secure by using provided 5mm Allen wrench (S).

STEP 4 Attach the monitor to the arm
TV
TV
TV TV
D
M-A
M-C
M-E
M-B
M-D
M-E
M-F
D
TV
TV
TV
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to back of monitor and secure with screws (M-A) or (M-C)
with washers (M-E). Avoid excessive tightening screws damage the monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to back of monitor and secure with screws (M-B) or (M-D)
with washers (M-E) and washers (M-F). Avoid excessive tightening screws damage the monitor.

STEP 5 Adjust the tension
Slide the monitor onto the head of swivel arm, install the security nut (N). Make
sure the security nut is installed before you rotate the monitor.
N
Adjust gas spring tension by turning
screw with 6mm Allen wrench (T) .
Clockwise(" - " direction) reduces
tension, counter Clockwise("+"
direction increases tension. The tension
should be just enough to hold your
monitor in place without lifting itself
up.
T
T
Be sure to keep the arm in horizontal
position during adjustment .0r else it
would be difficult to adjust the mount or
damage the mount.
If needed, adjust the bolt on
the side of the hinge behind
the VESA plate to tighten or
loosen the tilt angle support.
Use the provided Allen wrenches (S) to adjust screw
below the joint if it is too tight or loose.
We suggest not to adjust it frequently otherwise it
may cause damage to the joint of arms.
S

1
2
STEP 6 Cable Management
For both bottom and upper portion of the spring arm, just slide the cable cover up and away
from the spring arm, do not need to take much effort to pull the ends of the cable cover
away from the spring arm.
On the bottom portion of the spring arm, insert the cable and slide the cable cover down;
On the upper portion of the spring arm, press the tabs on the inside of the cable cover
slightly inward and slide down to reattach the cable cover.

STEP 7 Inser t the Allen Wr ench int o the Slot
Adjust monitorto the desired positionand insert Allen wrenches (R&T) intothe slot.
±180°
+45°
-45°
±90°
±180°
±135°
T
R

Why choose FEZIBO?
Many ergonomic office solutions come at high cost. Our mission is to use
innovation, creativity, and efficiency to produce a more affordable solution
that doesn't sacrifice quality and is easily accessible to the millions of home
and office workers globally.
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more FEZ I BO products, check out our website at: www.fezibo.com
[email protected] www.facebook.com/Fezi bous www.fezibo.com