FHM ECO-19 User manual

Chipper/Shredder models: ECO-19
READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS
CAREFULLY SAVE THESE INSTRUCTIONS.
Owner’s Manual
Chipper/Shredder with 2-Way Feed

The information and specifications included in this publication were in effect at the time of approval for printing.
This manual contains important safety instructions for Chipper/Shredders
READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY
SAVE THESE INSTRUCTIONS.
This owner’s manual is considered a permanent part of the chipper/shredder and
should remain with the chipper/shredder if resold.
For product questions or service,
CALL 1-541-895-3083
or go to www.betstproducts.com
When you call the help-line you will need to have the following information:
Date of Purchase: _______________________
Location of Purchase: _______________________
Serial #: _______________________

Contents
Warnings.......................................................................................................4
Warnings.......................................................................................................5
Component Identification.........................................................................6
Missing Parts Request Form....................................................................7
Safety Information.....................................................................................8
Operating Guidelines.................................................................................9
Assembly Instructions............................................................................10
Operating Instructions.............................................................................11
Maintenance and Storage........................................................................12
Troubleshooting......................................................................................14
Parts Breakdown .....................................................................................15
Parts•Request•Form...............................................................................22
LIMITED WARRANTY & REGISTRATION FORM...................................23
2 YEAR EXTENDED WARRANTY & REGISTRATION.............................25

Warnings
This symbol indicates important safety instructions
which, if not followed, could endanger personal safety
and/or property. Read and follow all instructions in this
manual before attempting to operate this machine.
Failure to comply with these instructions may result in
personal injury. When you see this symbol—heed its
warning.
CARBON MONOXIDE GAS
Exhaust contains poisonous carbon monoxide, a colorless
and odorless gas. Breathing exhaust can cause loss of
consciousness and may lead to death.
The Engine Exhaust from this product contains chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm.
This machine has a rotating cutting blade capable of
amputating hands and feet and throwing objects. Keep
hands and feet out of openings while machine is running.
Failure to observe these safety instructions could result in
serious injury or death.
WARNING: Do not operate this machine unless the chute
deflector has been installed properly.
Keep bystanders, helpers, pets, and children at least 75
feet from the machine while it is in operation. Stop
machine if anyone enters the area.
Wear hearing and eye protection while operating this
machine or if you are within 75 feet of this machine.
Thrown objects which ricochet can cause serious injury to
the eyes.
Never wear loose clothes or long jewelry and keep your
long hair under a headgear when operating machine.
Never operate this machine in bare feet or sandals.
Never use machine on a slope or hard smooth floor.
Gasoline is extremely flammable and the vapors are
explosive. Serious personal injury can occur when
gasoline is spilled on you or your clothing, which can
ignite. In the event of a gasoline spill, wash your skin and
change clothes immediately.
WARNING: Do not deposit branches larger than 3” x 4”
inches in diameter (depending on Model #, see Model
Specifications table pg 2) in the side chute. Do not
deposit branches larger than 1/4 inches into the funnel.
DO NOT force the branches into this machine, allow the
machine to automatically feed through.
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING

Training
1. Read, understand, and follow all instructions on the
machine and in the manual) before attempting to
assemble and operate. Keep this manual in a safe
place for future and regular reference and for
ordering replacement parts.
2. Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
3. Never allow children under 18 years old to operate
this machine. Children 18 years old and over should
read and understand the operation instructions and
safety rules in this manual and should be trained and
supervised by a parent.
4. Never allow adults to operate this machine without
proper instruction.
5. Keep bystanders, helpers, pets, and children at least
75 feet from the machine while it is in operation. Stop
machine if anyone enters the area.
6. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
7. Do not put hands or feet near rotating parts or in the
feeding chambers and discharge opening. Contact
with the rotating impeller can amputate fingers,
hands, and feet.
8. Never attempt to unclog either the feed intake or
discharge opening, remove or empty bag, or inspect
and repair the machine while the engine is running.
Shut the engine off and wait until all moving parts
have come to a complete stop. Disconnect the spark
plug wire and ground it against the engine.
Chipper/Shredder Model # Specifications
Warnings
Product Specifications
NOTE:
The operator or
user is
responsible for
accidents or
hazards
occurring to other
people, their
property, and
themselves.

Component Identification
If you are missing any parts, please complete the form on the next page and fax it back to us at:541-895-2756
Shredder Chute, for leaves and twigs
up to 1” diameter
Chipper Chute, for branches up to 3” x 5”
3-Point Cat-I tractor connections
Adjustable length 6 spline PTO
shaft Adjustable Height stand allow you to aline
tractor PTO and chipper/shredder PTO
Chip discharge

Missing Parts Request Form
Name
Phone
Email
Address
IMPORTANT: Please include your receipt. Without a receipt, your
order will be delayed. You may also email us at:
[email protected]. If emailing, please scan in
your proof of purchase.
Comments:
Please indicate the part that you are missing:
Hardware bag
Model #:
ECO-19
Wheel Kit
Other
Serial #:
Date of purchase

Safety Information
Preparation
1. Thoroughly inspect the area where the chipper/
shredder is to be used. Remove all rocks, bottles,
cans, or other foreign objects which could be picked up
or thrown and cause personal injury or damage to the
machine.
2. Avoid discharging chipped material out of the
discharge chute against a wall or on asphalt, concrete,
or other hard surfaces as material being ejected could
ricochet, causing injury to you or bystanders.
3. Always wear safety glasses or safety goggles to
protect eyes during operation or while performing an
adjustment or repair.
4. Wear sturdy, rough-soled work shoes and close fitting
pants and shirts. Loose fitting clothing or jewelry can
be caught in movable parts. Wear leather work gloves
when feeding material in the chipper chute.
5. Before starting the engine, check bolts and screws for
proper tightness to be sure the machine is in safe
working condition. Also, visually inspect the chipper
shredder at frequent intervals for any damage.
6. Maintain or replace safety and instructions labels, as
necessary.
7. To avoid personal injury or property damage use
extreme care in handling gasoline.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine
is hot or running.
e. Allow engine to cool at least two minutes before
refueling.
f. Never over fill fuel tank. Leave at least 1/2 inch
open below bottom of filler neck to provide space
for fuel expansion.
g. Tighten gasoline cap securely.
h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area and
wait 5 minutes before starting the engine.
i. Never store machine or fuel container inside near
an open flame, spark, or pilot light (e.g., furnace,
water heater, space heater, clothes dryer, etc.).
j. To reduce the fire hazard, keep machine free of
grass, leaves, or other debris build-up. Clean up
oil or fuel spills and remove any fuel soaked
debris.
k. Allow machine to cool at least 5 minutes before
storing.
8. Never attempt to make any adjustments while the
engine (motor) is running (except where specifically
recommended by the manufacturer).
Safety Label Locations
These labels warn you of potential hazards that can
cause serious injury. Read them carefully. If a label
comes off or becomes hard to read, contact your
PowRkraft for a replacement.
Safety Information
PowRkraft Outdoor Power products are designed to give
safe and dependable service if operated according to
instructions. Read and understand this owner’s manual
before operating your power equipment.
Operator Responsibility
Know how to stop your power equipment quickly in case
of emergency. Understand the use of all controls and
connections. Be sure that anyone who operates this
power equipment receives proper instruction. Do not let
children operate the power equipment without parental
supervision.
Your Responsibility
Restrict the use of this chipper/shredder to persons who read, understand and follow the
warnings and instructions in this manual and on the machine.
Note: Not all safety labels shown may apply to your chipper/shredder.

8. Never attempt to unclog either the feed intake or
discharge opening while the engine is running. Shut
the engine off, wait until all moving parts have
stopped, disconnect the spark plug wire and ground it
against the engine before clearing debris.
9. Never operate without the shredder funnel, chipper
chute, or discharge chute properly attached to the
machine. Never empty or change discharge bag
while the engine is running. Stop the engine when
leaving the operating position.
10. Keep all guards, deflectors and safety devices in
place and operating properly.
11. Keep your face and body back and to the side of the
chipper chute while feeding material into the machine
to avoid accidental kickback injuries.
12. Never operate this machine without good visibility or
light.
13. Do not operate on a non-level surface.
14. Do not operate in a confined space.
15. Do not operate this machine while under the
influence of alcohol or drugs.
16. Muffler and engine become hot and can cause a
burn. Do not touch.
17. Never pick up or carry machine while the engine is
running.
18. Do not leave this machine running while unattended
19. Keep children, bystanders, and pets 75 feet away.
20. Use only manufacturer approved accessories/
attachments.
READ THESE OPERATING GUIDELINES
BEFORE YOU PROCEED ANY FURTHER
1. Do not put hands and feet near rotating parts or in the
feeding chambers and discharge opening. Contact with
the rotating impeller can amputate fingers, hands, and
feet.
2. Before starting the machine, make sure the chipper
chute, feed intake, and cutting chamber are empty and
free of all debris.
3. Thoroughly inspect all material to be shredded and
remove any metal, rocks, bottles, cans, or other foreign
objects which could cause personal injury or damage
to the machine.
4. If it becomes necessary to push material through the
shredder hopper, use a small diameter stick. Do not
use your hands or feet.
5. If the impeller strikes a foreign object or if your
machine should start making an unusual noise or
vibration, immediately shut the engine off. Allow the
impeller to come to a complete stop. Disconnect the
spark plug wire, ground it against the engine and
perform the following steps:
a. Inspect for damage.
b. Repair or replace any damaged parts.
c. Check for any loose parts and tighten to assure
continued safe operation.
6. Do not allow an accumulation of processed material to
build up in the discharge area. This can prevent proper
discharge and result in kickback of material through
the feed opening.
7. Do not attempt to shred or chip material larger than
specified on the machine or in this manual. Personal
injury or machine damage could result.
Operating Guidelines
The upper chute on the
chipper/shredder is for
Leaves and twigs only.
Do not use the funnel
for vines or long
branches such as
Weeping Willows as
they may clog the flails.
The lower chute is for
longer and/or thicker
pieces of yard waste.
Depending on your
model, you may cut up
to a 3” x 5” in piece of
wood.

Required tools:
Approximate assembly time:
1. Remove the chipper from its carton.
Remove staples, break glue on top flaps, or cut tape at
carton end and peel along top flap to open carton.
2. Verify all parts are in the chipper
carton.
·Chipper Chute
·Chipper engine
and box
assembly
(pre-assembled)
·Chipper Chute
·Hardware Bag
·Trailer hitch and
funnel handles
packaged
together
Assembly Instructions

Using the Chipper Shredder
Yard waste such as leaves and pine needles can be
raked up and placed in the chipper funnel for shredding.
DO NOT PUT BRANCHES INTO THE CHIPPER
FUNNEL. BRANCHES SHOULD BE FED INTO THE
SIDE CHIPPER CHUTE.
When using the side chipper chute to chip branches, it is
important to let the chipper feed the branches through
automatically. DO NOT attempt to force the branches
through. If the branches do not automatically feed
through, gently push the branch and then allow the
chipper to automatically feed the branch through. Forcing
branches into the side chute may wear the belt
prematurely.
Once material is shredded by the hammers on the
impeller assembly, it is discharged through the open
discharge chute or into the chipper bag.
Do not attempt to shred or chip any material other than
normal yard vegetation found (i.e., branches, leaves,
twigs, etc.) Avoid fibrous plants such as tomato vines
until they are thoroughly dried. Twigs and small branches
can be fed into the chipper chute. (See model
specifications for maximum cutting thickness.)
IMPORTANT: The hammer screen is located inside the
housing in the discharge area. If the screen becomes
clogged, remove and clean as instructed. For best
performance, it is also important to keep the chipper
blade sharp.
Operating Instructions
This machine was built to be operated according to the
rules for safe operation in this manual. As with any type of
power equipment, carelessness or error on the part of the
operator can result in serious injury.
Always wear hearing and eye protection while
operating this machine or if you are within 75 feet of
this machine.
WARNING
DANGER

Maintenance and Storage
Maintenance Schedule
Always stop engine, disconnect spark plug, and
ground against engine before cleaning,
lubricating or doing any kind of maintenance on
your machine.
Maintenance and Storage
1. Never tamper with safety devices. Check their proper
operation regularly.
2. Check bolts and screws for proper tightness at
frequent intervals to keep the machine in safe working
condition. Also, visually inspect machine for any
damage and repair, if needed.
3. Before cleaning, repairing, or inspecting, stop the
engine and make certain the impeller and all moving
parts have stopped. Disconnect the spark plug wire
and ground it against the engine to prevent
unintended starting.
4. Do not change the engine governor settings or
overspeed the engine. The governor controls the
maximum safe operating speed of the engine.
5. Maintain or replace safety and instruction labels, as
necessary.
WARNING
6. Follow this manual for safe loading, unloading,
transporting, and storage of this machine.
7. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light such
as a water heater, furnace, clothes dryer, etc.
8. Always refer to the operator’s manual for proper
instructions on off-season storage.
9. If the fuel tank has to be drained, do this outdoors.
10. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
If the Chipper Becomes Clogged:
If the discharge area becomes clogged:
·Stop the engine. Disconnect spark plug wire from
spark plug and ground against the engine.
·Remove the large funnel and the clean out the
access hatch on the side of the chipper engine box
(as necessary).
·Reach in and clear the debris causing the blockage.
Reinstall the funnel and the clean out access hatch.
·Connect the spark plug wire and restart.
NOTE: If the blockage is severe, the hammer screen
within the discharge chute can be removed as well,
providing greater access. To accomplish this, remove the
pins and slide the flail screen out of the discharge chute.

Always stop engine, disconnect spark plug, and
ground against engine before cleaning,
lubricating or doing any kind of maintenance on
your machine.
Removing and Sharpening the Blade
The chipper was shipped with one blade attached and
one blade in the hardware bag. You can extend the belt
life by operating the chipper with a sharp blade.
·Disconnect the PTO Shaft
·Remove the blade access hatch and rotate the
blade to align with the access hatch.
·Remove the flail screen in the discharge chute by
removing the pins that secure it at the top and
bottom of the screen.
·Remove the blade using a 3/16” Allen wrench on the
outside of the blade and an adjustable wrench on
the impeller assembly (through the discharge
chute). Use a piece of pipe or wood to block the
flails, preventing them from inadvertently turning.
·Add, replace or sharpen the blade as desired.
·When sharpening the blade, protect hands by using
gloves and following the original angle of
Grind. Torque to 250–300 in. lbs.
NOTE: Make certain the blade is reassembled with the
sharp edge facing upward.
Changing or Tightening the Belt
NOTE: The belt is designed to be the weakest link in the
mechanical linkage between the engine and the blade.
This improves the safety and durability of the chipper/
shredder.
Occasionally, changing or tightening the belt is required.
To change the belt:
·Stop the engine and make certain the chipper/
shredder has come to a complete stop. Disconnect
the PTO Shaft from tractor.
·Remove the belt guard.
·Loosen engine mount bolts and release belt tension.
Pry the belt off the pulley using a screw driver shaft
as a wedge as you rotate the pulley. Place a new
belt on the pulleys in a similar fashion.
To tighten the tension on the pulleys, follow the above
steps plus:
Maintenance & Storage
·Scribe a mark on the base plate along the edge of
the engine.
·Remove the belt from the pulleys.
·Remove the handle, discharge chute and screen.
·Loosen the four bolts securing the engine.
·Slide the engine about 1/8” further back.
·Tighten the engine mounting bolts securely.
·Re-install the belt and verify the tension. If the belt is
still too loose, move the engine back another 1/8” by
repeating the above steps.
·Reinstall guards, chutes, and screens.
Cleaning the Chipper/Shredder
·Make sure engine is off.
·Wipe off machine with an oiled rag to prevent rust.
·If the fuel tank has to be drained, do so outdoors.
·Observe proper disposal laws and regulations for
gas, oil, etc., to protect the environment.
Storing the Chipper/Shredder
·Clean the equipment thoroughly.
·Wipe equipment with an oiled rag to prevent rust.
·Refer to engine manual for correct engine storage
instructions.
·Store unit in a clean, dry area. Do not store next to
corrosive materials such as fertilizer.
·Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
such as a water heater, furnace, clothes dryer, etc.
WARNING

Troubleshooting

Parts Breakdown

Parts - Adjustable Stand
Skid & Leg Assembly
Modified Main Frame

EC019.001 PARTS LIST
REF. PART NUMBER DESCRIPTION QTY.
1 LS18.101 HANDLE COVER 1
2 ECO19.101 DRAW BAR 1
3 DP8x60 LOCK PIN D8x60 D 8x60 1
4 GB6170-M12 NUT M12 M12 4
5 LP12 LOCK PIN 12 • 12 2
6 T150.101 LOWER HITCH PIN 2
7 ECO19.011 MAIN FRAME,WDMT 1
8 GB5782-M10x90 BOLT M10x90 M10x90 1
9 GB97.1-10 PLAIN WASHER 10 10 22
10 GB889.1-M10 LOCK NUT M10 M10 14
11 ECO19.102 CONNECTING ROD 1
12 ECO19.021 WHEEL,SET 2
13 DP12x60 LOCK PIN D12x60 D 12x60 2
14 GB5783-M8x20 BOLT M8x20 • M8x20 4
15 GB97.1-8 PLAIN WASHER 8 8 5
16 GB889.1-M8 LOCK NUT M8 M8 5
17 ECO19.020 SHIELD,PULLEY 1
18 REACH 04-3360 CLAMPING COUPLING 3360 • 3360 1
19 EFGC125.121 PULLEY 1
20 GB11544-SPB1295 V-BELT SPB1295 V SPB1295 2
21 ECO19.105 CONNECTING PLATE 1
22 GB5783-M12x35 BOLT M12x35 M12x35 4
23 GB93-12 LOCK WASHER 12 12 4
24 GB97.1-12 PLAIN WASHER 12 12 4
25 ECO19.012 MOUNTING BASE,GEARBOX 1
26 GB5782-M10x75 BOLT M10x75 M10x75 10
27 TS50.300Z.02 GEARBOX,ASSY 1
28 ECO19.002 CHIPPER,ASSY 1
29 ECO19.016 DISCHARGE COVER 1
30 ECO19.106 DISCHARGE FLAP 1
31 ECO19.107 CLAMPING PLATE 3
32 JB4005-6x12 RIVET 6x12 6x12 6
33 GB5783-M10x25 BOLT M10x25 M10x25 4

Parts Breakdown - Continued

EC019.002 PARTS LIST
REF. PART NUMBER DESCRIPTION QTY.
1 REACH 04-3560 CLAMPING COUPLING 3560 • 3560 1
2 ECO19.103 PULLEY 1
3 F90507 BEARING F90507,SET F90507 2
4 GB889.1-M12 LOCK NUT M12 M12 8
5 GB97.1-12 PLAIN WASHER 12 12 8
6 ECO19.003 ROTOR,ASSY 1
7 GB5783-M10x25 BOLT M10x25 M10x25 4
8 GB93-10 LOCK WASHER 10 10 4
9 GB97.1-10 PLAIN WASHER 10 10 4
10 ECO19.019 PATCHING PLATE,WDMT 2
11 ECO19.013 HOUSING,WDMT 1
12 R PIN 3.2 R PIN 3.2 R 3.2 2
13 ECO19.017 SIFTING PLATE,WDMT 1
14 ECO19.018 SIFTING PLATE,WDMT 1
15 ECO19.109 SUPPORTING ROD 2
16 ECO19.022 COVER,BEARING 1
17 GB5783-M10x25 BOLT M10x25 M10x25 4
18 GB93-10 LOCK WASHER 10 10 4
19 GB97.1-10 PLAIN WASHER 10 10 4
20 ECO19.015 UPPER HOPPER 1
21 ECO19.111 ENTRANCE FLAP,UPPER 1
22 ECO19.112 CLAMPING PLATE 2
23 JB4005-6x12 RIVET 6x12 6x12 6
24 ECO19.110 ENTRANCE FLAP,LOWER 1
25 ECO19.014 LOWER HOPPER 1
26 GB889.1-M8 LOCK NUT M8 M8 3
27 GB97.1-8 PLAIN WASHER 8 8 3

Parts Breakdown - Continued