Finlux ST-55U01 User manual
55” (140cm) BIG SIZE MONITOR
55” (140cm) LAAJAKUVANÄYTTÖ
55” (140cm) STOR BILDSKÄRM
ST-55U01
ENGLISH - SUOMI - SVENSKA
USER MANUAL
KÄYTTÖOHJE
ANVÄNDARMANUAL
English - 1 -
Contents
Important Safety Information ..................................2
General View..........................................................6
Control Buttons on the Display...............................7
Connecting the IR Receiver....................................8
Turning the Display On/Off .....................................8
Remote Control ......................................................9
First Time Installation............................................10
Media Playback via USB Input .............................10
Display Menu Contents ........................................ 11
Connectivity..........................................................14
Internal USB Operations (*)..................................17
OSD Rotation Support (*).....................................17
DisplayPort ...........................................................18
Controlling With An External PC...........................18
RS232 Command Table .......................................20
System Features ..................................................32
............................................................32
English - 2 -
• Please provide the plug and socket to supply the
needed power for appliance.
• Please place the product in a position that electric
cables cannot be affected by the operations on the
product.
• Follow all warnings and instructions marked on the
product.
• Follow the on screen instructions for operating the
related features.
•
do not overuse the plugs and extension cords.
Please do not open the lid of the monitor to service
yourself. If the required service needs are not met
other risks may occur.
• If you will not use the product for a long period of
• Put the product on a well-ventilated place and
• The product should be kept in 0 C° - 40 C°.
permanently.
• Plug the appliance to a grounded outlet. Always use
the grounded power cord supplied with your product.
Manufacturer is not responsible for any damage
caused unearthed usage.
• The socket-outlet shall be installed near the
equipment and shall be easily accessible.
• Do not stay in contact with the parts of the product
that become hot for long periods of time. Doing so
may result in low-temperature burns.
• The LCD panel used in this product is made of glass.
or applied with impact. Be careful not to be injured by
broken glass pieces in case the LCD panel breaks.
• Usage of the monitor must not be accompanied
missile launch control in a weapon system.
• Do not expose the product to direct sunlight or do
of or near the product.
• Do not place any heat sources such as electric
•
product from the mains.
• Do not touch the controls other than those described
in the operating instructions. Improper adjustment of
controls not described in the instructions can cause
Important Safety
Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Please read these instructions fully and
carefully before use and keep for future
reference
WARNING: This device is not intended for
use by persons (including children) without
physical, sensory or mental capabilities, or lack
of experience and/or knowledge unless they have
been given supervision or instruction concerning
use of the device by a person responsible for
their safety.
• This product is for indoor use only.
• Use this product at an altitude of less than 2000
meters above the sea level and in dry locations and
in regions with moderate or tropical climates.
• Please keep this manual for further use.
• Unplug your product before starting to clean. Do
not clean the product when it is on. Do not use
liquid or aerosol cleaners. Use a damp cloth for
display cleansers. Do not apply the cleaner directly
on the product.
•
accessories.
•
• Do not expose the product to dripping or splashing
• Please leave at least 5 cm of free space between the
product and walls or other furnitures for ventilation
purposes.
•
power source on its rating plate. For further
•
plug is given with the product. If you cannot plug the
any change on the grounding plug.
English - 3 -
• Do not shake the product. Ensure that it stays in a
balanced stance on its position.
• Do not throw or drop any object on your product.
• Do not interfere on your products screen or any other
surface with a sharp object.
• Do not keep your product in a humid environment.
• Do not keep your product in an extremely cold
environment.
• Do not keep your product in an extremely hot
environment.
•
surfaces.
•
animals.
Vent holes of the product
The vent holes are designed to provide the product
to work constantly and prevent it from overheat. Do
not block these openings in anyway. For the same
Never insert an object into the product through vents
inserting any objects in the vents or openings of the
spill water or liquid on the product.
Repair
Unless a basic implementation on the product is
you may risk your health or your product. In case of
• When the cable is worn off or harmed.
• If the product has been dropped or the cabinet has
been damaged.
• If the performance of the product is changed or the
appliance needs to be repaired.
• When a liquid was spilled on the product or when
objects have fallen into the product.
• When the product has been exposed to rain or water.
• When the product does not operate properly as
described in the operating instructions.
Replacement parts
sure that the service person uses replacement parts
characteristics and performance as the original parts.
shock and/or other danger.
Safety checks
service technician to perform safety checks to ensure
that the product is in proper operating condition.
Wall mounting
the product according to the method recommended
by the manufacturer.
• Read the instructions before mounting the product
on the wall.
• The wall mount kit is optional. You can obtain from
• Do not install the product on a ceiling or on an
inclined wall.
•
accessories.
•
the product from fall. Do not over-tighten the screws.
Power Cord
• The power cord is used to disconnect the product
from the mains and therefore it must remain
readily operable. If the product is not disconnected
power for all situations even if the product is in
standby mode or switched off.
• Use only the power cord supplied with the monitor.
• Do not damage the power cord nor place heavy
•
on the plug. Do not pull from the cable when
unplugging the appliance.
• Do not use the power cord with a power tap. Adding
overheating.
• Do not remove or insert the power plug with wet
hands. Doing so could result in electric shock.
• Unplug the power cord if it is not used for a long time.
• Do not attempt to repair the power cord if it is
broken or malfunctioning. When damaged it must
personnel.
Especially for child safety
•
monitor.
•
English - 4 -
Intended Use
• Product should be used for household and similar
general use but which may also be used in places of
places of worship.
• Product is only suitable for connecting commercial
mains socket outlets. Do not connect product
industrial socket outlets.
Foreseeable misuse and incorrect use
•
or aircraft or at altitudes exceeding 2000m above sea
other than mentioned in user manual additional
requirements may be necessary.
CAUTION
Do not leave a static image displayed for pro-
longed period of time. If a static image is displayed
may cause image sticking on the display. This con-
-
erable amount of operational display time to dissi-
120 minutes of continuous motion display will elim-
inate most image sticking effects at normal room
temperature (not lower than 10 C).
-
fect the performance of the computer and are not
accepted as a defect.
Warning
This is a class A. In a domestic environment this may
cause radio interference in which case the user may
be required to take adequate measures.
BATTERY SAFETY GUIDELINES
dependable source of portable power. Problems
can occur if they are misused or abused resulting in
Here are some simple guidelines to safe battery use
designed to eliminate any such problems.
•
plus and minus marks on the battery and appliance.
•
care not to mix old and new batteries or batteries of
• Remember that children can become excited while
monitor. Care should be taken to place or install the
knocked down.
• Care should be taken to route all cords and cables
connected to the monitor so that they cannot be
pulled or grabbed by curious children.
Connections
Be sure to turn off the main power switch and
disconnect the plug from the power outlet before
manual of the equipment to be connected.
Be careful not to confuse the input terminal with the
output terminal when connecting cables. Accidentally
reversing cables connected to the input and output
terminals may cause malfunctions and other
problems.
Positioning
by taking simple pre-cautions such as:
• Using fixing devices like wall mount brackets
recommended or supplied by the manufacturer.
• Only using furniture that can safely support the
monitor.
• Ensuring the monitor is not overhanging the edge
of the supporting furniture.
•
cupboards or bookcases) without anchoring both
the furniture and the monitor to a suitable support.
• Not standing the monitors on cloth or other materials
placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on
furniture to reach the monitor or its controls. If your
same considerations as above should be applied
Transport and Shipping
• Your device must be kept in its original package
to protect from damage to its accessories during
transport and shipping.
• Keep the product in normal position during transport.
• Do not drop the device during transport and protect
it against impacts.
• Damages and faults that occur during transport after
the delivery of the appliance to the customer are not
included in the warranty cover.
•
personnel.
English - 5 -
• Store unused batteries in their packaging and away
from metal objects which may cause a short-circuit
even an explosion.
• Remove dead batteries from equipment and all
batteries from equipment you know you are not going
to use for a long time. Otherwise the batteries may
leak and cause damage.
• Batteries must not be exposed to excessive heat
•
explode. Please recycle dead batteries; do not put
with the normal household waste.
•
in a charger or by applying heat to them. They may
rechargeable batteries which are clearly marked
as such.
• Supervise children if they are replacing batteries
themselves in order to ensure these guidelines are
followed.
•
• This product or the accessories supplied with the
product may contain a coin/button cell battery. If the
severe internal burns in just 2 hours and can lead
to death.
• Remember that small button cell batteries such as
and this can be dangerous.
•
• Make sure battery compartments are secure. If the
•
•
rinse immediately and thoroughly. If it gets into your
seek medical treatment immediately. Leaked battery
cause a skin irritation or damage your eye.
CAUTION
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
Markings on the Product
The following symbols are used on the product as
a marker for restrictions and precautions and safety
such information for security reasons.
Class II Equipment: This appliance is
designed in such a way that it does not require
a safety connection to electrical earth.
Class II Equipment With Functional
Earthing: This appliance is designed in such
a way that it does not require a safety
used for functional purposes.
Protective Earth Connection: The marked
terminal is intended for connection of the
protective earthing conductor associated with
the supply wiring.
Hazardous Live Terminal: The marked
terminal(s) is/are hazardous live under normal
operating conditions.
Caution, See Operating Instructions: The
marked area(s) contain(s) user replaceable
coin or button cell batteries.
Any issues which are caused by customer mis-adjustment
of any software including the operating system are not
covered by the warranty.
Depending on the model you buy, the actual
appearance of the product may differ from the images
used in this manual.
i
English - 6 -
General View
Front Side
1
1. LCD Panel
Rear Side (1)
1. VGA
2. RS232
3. DVI
4.
5.
6. HDMI 1
7. Headphone
8. USB
9. USB (3.0)
10. IR Input
11. HDMI 2
123
4
6
8
7
9
10
11
5
English - 7 -
Rear Side (2)
1. Audio Out
2. Audio In
3. Ethernet
4. RJ12
5.
6. YPbPr
7.
1
3
4
7
2
6
5
1. Standby/On
2. Source / Select in Display menu
3. Open the brightness setting
/ Move the focus up (when in
Display menu)
4. Open the contrast setting /
Move the focus up down (when
in Display menu)
5. Volume + / Set or move the
focus right (when in Display
menu)
6. Volume - /Move the focus left
(when in Display menu)
1
2
3
5
4
6
Note: Press the Volume +/- buttons simultaneously to view the main menu and use P/CH +/- buttons to navigate and Volume
+/- buttons to change value.
English - 8 -
Turning the Display On/Off
Press the Standby button on the remote or on rear left side of the Display to switch it on from standby or to
switch it into standby mode.
TV/AV
- P/CH +
- +
MENU
Standby
Button
Standby Button
LED Status Status of the monitor
Power led not lit Power on
Power led lit Power off (Standby mode)
Input signal waiting mode
English - 9 -
Remote Control
(*) MY BUTTON1 & MY BUTTON2:
These buttons may have default functions depending on
the model. However you can set a special function to these
buttons. Switch to a desired input source and press and hold
be displayed on the screen. Now MY BUTTON is associated
with the selected source.
Note that if you perform First time installation
&2 will return to their default function.
Inserting the Batteries into the Remote
Lift the cover on the back of the remote gently. Insert two AAA
batteries. Make sure the (+) and (-) signs match (observe
correct polarity). Place the cover back on.
1. Standby: Switches On / Off the Display
2. Numeric buttons: Enters a number or a letter in the text
box on the screen.
3. No function
4. Mute: Completely turns off the volume of the Display
5. Volume +/-: Increases or decreases the volume
6. Menu: Displays the main menu
7. Directional buttons:
8. OK:
9. Back/Return: Returns to previous screen
10. Media browser: Opens the media browsing screen
11. Info: Displays information about on-screen content.
12. My button 1 (*)
13. Coloured Buttons:Follow the on-screen instructions
for coloured button functions
14. Language:
and changes audio/subtitle language (in media browser
mode)
15. Subtitles: Turn subtitles on and off (where available)
16. Rapid reverse: Moves frames backwards in media
such as movies
17. No function
18. Play: Starts to play selected media
19. Stop: Stops the media being played
20. Rapid advance: Moves frames forward in media such
as movies
21. Pause: Pauses the media being played
22. Screen: Changes the aspect ratio of the screen
23. No function
24. My button 2 (*)
25. No function
26. Exit: Closes and exits from displayed menus or returns
to previous screen
27. Quick Menu: Displays a list of menus for quick access
28. Internet : No function
29. No function
30. Swap: Quickly cycles between previous and current
sources
31. Source: Shows all available content sources
English - 10 -
First Time Installation
selection screen will be displayed. Select the desired
language and press OK.
press OK
your OSD (On Screen Display) rotation preference
on this screen.
You can activate Store Mode option at this point.
store environment and depending on the Display
may be displayed on the top of the screen as an
info banner. This option is intended only for store
use. It is recommended to select Home Mode
for home use. This option will be available in
System>Settings>More menu and can be turned
off/on later.
Press OK button on the remote control to complete
To repeat this process and reset the Display's settings
to the factory defaults enter the Installation
highlight First time installation and press OK.
whether you want to delete all settings. Select Yes
and press OK
Note:
installation. Note that, some options may not be available
depending on the country selection.
Media Playback via USB Input
You can connect 2.5” and 3.5” inch (hdd with external power
supply) external hard disk drives or USB memory stick to your
Display by using the USB input/s of the Display.
IMPORTANT! Back up the files on your storage
devices before connecting them to the Display.
Manufacturer will not be responsible for any file
damage or data loss. Certain types of USB devices
(e.g. MP3 Players) or USB hard disk drives/memory
sticks may not be compatible with this Display. The
Display supports FAT32 and NTFS disk formatting.
Wait a little while before each plugging and unplugging
so may cause physical damage to the USB player
and the USB device itself. Do not pull out your drive
input/s. External power supplied USB hubs are
recommended in such a case.
Note:Media Browser menu
USB device.
English - 11 -
Display Menu Contents
System - Picture Menu Contents
Mode You can change the picture mode to suit your preference or requirements. Picture mode can
be set to one of these options: CinemaGameSportsDynamic and Natural.
Contrast
Adjusts the light and dark values on the screen.
Brightness
Adjusts the brightness values on the screen.
Sharpness
Sets the sharpness value for the objects displayed on the screen.
Colour
Energy Saving
For setting the Energy Saving to CustomMinimumMediumMaximumAuto
Screen Off or Off.
Note: Available options may differ depending on the selected Mode.
Backlight This setting controls the backlight level. The backlight function will be inactive if the
Energy Saving is set to an option other then Custom.
Advanced Settings
Dynamic Contrast
You can change the dynamic contrast ratio to desired value.
Noise Reduction Noise Reduction setting to reduce
the amount of noise.
Colour Temp Sets the desired colour temperature value. CoolNormalWarm and Custom options are
available.
White Point If the Colour Temp option is set as CustomIncrease the
Picture Zoom
Sets the desired image size format.
Film Mode Films are recorded at a different number of frames per second. Turn this feature on when you are
Skin Tone
Skin tone can be changed between -5 and 5.
Colour Shift
Adjust the desired colour tone.
HDMI Full Range
enhance blackness in the picture.
PC Position Appears only when the input source is set to VGA/PC.
Autoposition
Automatically optimizes the display. Press OK to optimize.
H Position
This item shifts the image horizontally to the right hand side or left hand side of the screen.
V Position
This item shifts the image vertically towards the top or bottom of the screen.
Dot Clock Dot Clock adjustments correct the interference that appear as vertical banding in dot
intensive presentations like spreadsheets or paragraphs or text in smaller fonts.
Phase Depending on the input source(computer etc.) you may see a hazy or noisy picture on the
screen. You can use phase to get a clearer picture by trial and error.
Reset Resets the picture settings to factory default settings (except Game mode).
While in VGA (PC) mode, some items in Picture menu will be unavailable. Instead, VGA mode settings will be added to the Picture
Settings while in PC mode.
English - 12 -
System - Sound Menu Contents
Volume Adjusts the volume level.
Equalizer
Selects the equalizer mode. Custom settings can be made only when in User mode.
Balance Adjusts whether the sound comes from the left or right speaker.
Headphone
Sets headphone volume.
Please ensure before using headphones that the headphone volume is set to a low
Sound Mode You can select a sound mode (If the viewed channel supports).
Audio Link Press OK to open the Audio Link menu screen. Using this screen you can discover
and connect the sound devices to your Display wirelessly.
AVL (Automatic
Volume Limiting)
Headphone/Lineout
can select this option as Lineout
set this option as Headphone.
Please ensure before using headphones that this menu item is set to Headphone.
If it is set to Lineout
which could damage your hearing.
Dynamic Bass Enables or disables the Dynamic Bass.
Surround sound
Surround sound mode can be changed as On or Off.
Digital Out Sets digital out audio type.
System - Settings Menu Contents
Language
You may set a different language depending on the broadcaster and the country.
Parental
Enter correct password to change parental settings. You can easily adjust Menu Lock
or Child Lock in this menu. You can also set a new PIN using the Set PIN option.
Note: Some menu options may not be available depending on the country selection in the First Time
Installation. Default PIN can be set to 0000 or 1234
.
Sources
Enables or disables selected source options. There are Regular Enhanced and
Disabled options available for HDMI sources. Regular and Enhanced options are
affecting the colour settings of the selected HDMI source. To be able to watch 4K images
from an HDMI source related source setting should be set as Enhanced if the connected
device is HDMI 2.0 compatible. Set as Regular if the connected device is HDMI 1.4
compatible. Set acoordingly or disable the related HDMI source by setting as Disabled.
Network/Internet
Settings Displays network/internet settings.
More Displays other setting options of the Display.
Menu Timeout
Changes timeout duration for menu screens.
Software
Upgrade OK to see the menu options.
Application
Version Displays current software version.
Auto Display
OFF
Sets the desired time for the Display to automatically go into standby mode when not
being operated.
Store Mode Select this mode for store display purposes. Whilst Store Mode
items in the Display menu may not be available.
English - 13 -
Audio Video
Sharing
Audio Video Sharing
you can share/play photos on your Display. See instructions of your sharing software for more
information. Audio Video Sharing mode will not be available with internet portal feature.
Power Up Mode Last State and Standby
options are available.
Virtual Remote Enable or disable the virtual remote feature.
Speakers
To hear the Display audio from the connected compatible audio device set as
. You can use the remote control of the Display to control the volume of the
audio device.
OSD Rotation (*)
This setting allows you to change the OSD (On Screen Display) rotation of your
Display by selecting the desired option.
(*) This feature may not be available depending on the model of your Display
DP Stream
Setting (*)
Sets the DisplayPort stream type. MST and SST options are available.
(*) This menu item appears only when the input source is set to DP.
Smart Remote Press OK to open the Smart Remote menu screen. Using this screen you can discover
and connect the remote controller devices to your Display wirelessly.
If this feature is enabled the Display can be turned on again through the virtual remote
in the Smart Center application if it is turned off through it. Press Left or Right button
to enable or disable the feature.
Installation Menu Contents
First time
installation
PIN to start First time installation.
Note: Default PIN can be set to 0000 or 1234
System>Settings>Parental Settings
English - 14 -
Connectivity
to the
System>Settings menu.
Wired Connectivity
To Connect to a Wired Network
• You must have a modem/router connected to an
•
Broadband ISP connection
LAN (ethernet) cable
LAN input on the rear
side of the Display
Network Type
The Network Type can be selected as Wired Device,
Wireless Device or Disabled
active connection to the Display. Select this as Wired
Device if you are connecting via an ethernet.
Internet Speed Test
Internet Speed Test and press the OK
Advanced Settings
Advanced and press the OK but-
ton. On the next screen you can change the IP and
from to Manual. Now you can enter the
Manual IP and / or Manual DNS values. Select the
Press the OK
Wireless Connectivity
To Connect to a Wireless Network
The Display cannot connect to the networks with a
you should change your SSID settings via the
Broadband
ISP
connection
• A Wireless-N router (IEEE 802.11a/b/g/n) with
simultaneous 2.4 and 5 GHz bands is designed
to increase bandwidth. These are optimized for
transfers and wireless gaming.
•
the area.
•
•
•
•
Open the menu and select
Network Type as
process.
Note: If the modem supports N mode, you should set N
mode settings.
English - 15 -
buttons and the OK button on the remote control.
Network Type
as .
you can directly connect your Display to the modem/
router without entering a password or adding the
Highlight the
router option and press the OK button. Then press
the WPS button on your router/modem to connect.
Internet Speed Test and press the OK button
Advanced and press the OK button to open
buttons to set. Press the OK
when complete.
Other Information
Connected or Not Connected and the current IP
•
•
•
•
• Enter the menu and the playback
OK
•
controller application from the server of your mobile
device application provider.
Note: This feature may not be supported on all mobile devices.
Wireless Display
Wireless Display is a standard for streaming video
and sound content by Wi-Fi Alliance. This feature
provides the ability to use your Display as wireless
display device.
Using with mobile devices
There are different standards which enable sharing of
between your mobile device and Display.
Then press the Source button on the remote and
switch to Wireless Display source.
A screen appears stating that the Display is ready
for connection.
Open the sharing application on your mobile device.
These applications are named differently for each
mobile device for detailed information.
Scan for devices. After you select your Display and
on your Display.
Note: This feature can be used only if the mobile device
supports this feature. Scanning and connecting processes
differ according to the programme you use. Android based
mobile devices should have the software version V4.2.2
and above.
Connecting Other Wireless Devices
Your Display supports another short range wireless
connection technology too. A pairing is required before
using these kind of wireless devices with the Display
set. You should do the followings to pair your device
with the Display:
• Set the device to pairing mode
• Start device discovery on the Display
Note: Refer to the user manual of the wireless device to learn
how to set the device to pairing mode.
You can connect audio devices or remote controllers
wirelessly to your Display. Unplug or switch off any
other connected audio device in order for wireless
connection feature to work correctly. For audio
devices you should use the Audio Link option in the
System>Sound
Smart Remote option in the System>Settings>More
menu. Select the menu option and press the OK
button to open the related menu. Using this menu
you can discover and connect the devices that use
the same wireless technology and start to use them.
Follow the on-screen instructions. Start the device
discovery. A list of available wireless devices will be
displayed. Select the device you want to connect from
the list and press the OKDevice
connected
is successfully established. If the connection fails
try it again.
Note: Wireless devices may operate within the same radio
frequency range and may interfere with one another. To
improve the performance of your wireless device place it at
least 1 meter away from any other wireless devices.
English - 16 -
Connectivity Troubleshooting
Wireless Network Not Available
•
Display wireless connection.
•
menu screen.
using the wired network in your home. Refer to the
Wired Connectivity section for more information on
the process.
Connection is Slow
Distruption during playback or slow
reactions
You could try the following in such a case:
Keep at least three meters distance from microwave
other Wi-Fi compatible devices. Try changing the active
channel on the WLAN router.
Invalid Domain
Ensure that you have already logged on to your PC
Using Audio Video Sharing Network
Service
home network.
with the Nero Media Home programme. For more
Nero Media Home Installation
See the Wired/Wireless Connectivity chapters for
Select Media Browser by using the directional buttons
from the main menu and press OK. The media browser
will then be displayed.
Audio Video Sharing
Media Browser Folder
go to the Settings tab in the main media browser screen
and press OK. Highlight View Style and set to Folder
using the Left or Right buttons. Select the desired media
type and press OK.
Device
Selection screen will be displayed after selecting the
they will be listed on this screen. Select media server
or network that you want to connect to using the Up
or Down buttons and press OK. If you want to refresh
Green button. You can press
Menu to exit.
If you select the media type as Videos and choose
a device from the selection menu. Then select the
back to main Media Browser screen and select the
media type as desired and then perform the network
selection again. Or press the Blue button to switch to
next media type quickly without changing the network.
Refer to the Media Browser menu section for further
English - 17 -
You can connect only one display to the same network.
your display off at the wall socket and back on again.
other devices like computers.
Note: There may be some PC’s which may not be able to
and security settings (such as business PC’s).
For best home network streaming with this Display, the Nero
software should be installed.
Nero MediaHome Installation
follows:
Note:
1. Enter the link below completely in the adress-bar
of your web browser.
http://www.nero.com/mediahome-tv
2. Click the Download button on the opening page.
PC.
3.
4.
5. Click the Install
6. Click the Next
Please read
the license agreement carefully and select the
appropriate check box if you agree to the terms of
the agreement. Installation is not possible without
this agreement.
7. Click the Next button. On the next screen you can
set your installation preferences.
8. Click the Install
9. Click the Finish button. The installation is
completed. You will be directed to the web site of
the nero software.
10. A shortcut is now placed on your desktop.
Run Nero MediaHome by double clicking on the shortcut
icon.
Internal USB Operations (*)
Your Display has an internal memory. There are 4
operations available that can be performed with the
internal memory: Copy From USBCopy To USB
Delete and Format Disk.
These options can be found in the Diagnostic>Internal
USB Operations menu in the hidden service menu
Menu-4-7-2-5 buttons on the remote consecutively.
The internal memory of your Display has a default
int_usb
Copy From/To USB operations are performed using
this folder. If you want to copy data from an external
USB storage device to the internal memory of your
copy_to_int_usb
of the external USB storage device. If you want to
copy data from the internal memory of your Display
copy_from_int_usb
directory of the external USB storage device.
Copy From/To USB operations will only be available
if a USB storage device is connected to your Display.
Delete and Format Disk
even if no USB storage device is connected. The
int_usb
internal memory will be automatically recreated after
each time Delete and Format Disk operations are
performed.
(*) This feature may not be available depending on the model
of your Display
OSD Rotation Support (*)
You can change the OSD (On Screen Display) rotation
of your Display if desired. While performing First
time installation set the OSD Rotation option as
desired. You can also change this setting later from
the System>Settings>More menu. Available options
are: 090 CW90 CW - Fit180270 CW90 CW -
Fit270 CW - Fit.
(CW: Clockwise, Fit: Maximum width for 90 CW and 270
CW angles)
(*) This feature may not be available depending on the model
of your Display
English - 18 -
DisplayPort
DisplayPort version 1.2 is supported via the Display-
Port input and output connectors on your Display.
DP Streaming Setting option in the Settings>Other
Settings menu is set as MST(Multi-Stream Transport)
by default. If a MST compliant source device is
DisplayPort version 1.1 compliant or SST (Single-
Stream Transport) compliant source device with
DisplayPort version 1.2 support is connected to the
in all connected Displays.
To be able to stream the same image to all connected
DP Streaming
Setting option in the Settings>More menu should be
set as SST.
The maximum amount of the Displays that can be
connected by using daisy-chaining function may differ
capable of supporting this operation.
RS-232
Input Socket
To COM port
RS-232 to
USB Adaptor
PC
You can control the product from an external PC via
source can be changed by RS-232 from remote
computer. When a command is sent from the PC to
received command and sends a response message
to the PC.
Equipment/Tools:
• RS-232 (female) to RS-232(male) cable
• USB to RS-232(male) cable
• Notebook or PC which has USB port
• Installed program on remote PC to send commands:
operating the implemented functions via serial port
and help documents can be found Docklight website.
Connecting to the Display
English - 19 -
Download and install the PuTTY software from the
Host Name1986
PortTelnetConnection
type and click the Open button.
Note: Refer to the Connectivity section of this manual for
information on connecting the Display to a network and
displaying the IP address of the Display.
Use the commands in the RS232 Command Table.
current volume level should be displayed on the putty
window as shown in the pictures below.
Another example;
the changes from the Display.
The last example ;
source should be displayed on the putty window as
shown in the picture below.
Table of contents
Languages:
