Fisher & Paykel OM25BLCX1 User manual

Microwave oven
Installation instructions
OM25BLCX1 model NZ AU
Important!
SAVE THESE INSTRUCTIONS
The model shown in this document may not be available in all markets and is subject to change at any time. For current details about model and specification availability in your country, please go to our local website
listed at the end of this document or contact your local Fisher & Paykel dealer.
4CABINETRY DIMENSIONS
D D
B
C
C
A
E
E
Installation diagrams for illustration purposes only
Cabinetry dimensions (mm) OM25BLCX1 model
Awidth 600
Binside width 560 +8
Cdepth 550
Dheight 450 +2
Eair vent 45
Cut out dimensions above are to be used as minimum dimensions.
3PRODUCT DIMENSIONS
A
B
C
Installation diagrams for illustration purposes only
Product dimensions (mm) OM25BLCX1 model
Amicrowave height 460
Bmicrowave width 595
Cmicrowave depth 470
1SAFETY AND WARNINGS
WARNING!
Electric Shock Hazard
Read and follow the IMPORTANT SAFETY INSTRUCTIONS outlined in this
Installation instructions before installing or operating this appliance.
Failure to do so can result in death, electric shock, fire or injury to persons.
Important safety instructions

The oven is fitted with a plug and must be only connected to a properly installed earthed socket. In
accordance with the appropriate regulations, the socket must only be installed and the connecting
cable must only be replaced by a qualified electrician.

If the plug is no longer accessible following installation, an all-pole isolating switch must be present on
the installation side with a contact gap at least 3mm.

This microwave oven must be placed on a flat, stable surface to hold its weight and the heaviest food
likely to be cooked in the oven.
2GETTING STARTED
Tools required (not included)

No. 2 drill bit – long

Electric drill

Phillips head screwdriver
Parts supplied
Screw type A (x 2) Bracket (x 1) Screw type B (x 1) Plastic cover (x 1)

Do not place the oven where heat, moisture, or high humidity are generated, or near combustible
materials.

Do not operate the oven without glass tray, roller support and shaft in their proper positions.

Make sure that the power supply cord is undamaged and does not run under the oven or over any hot
or sharp surface.

Do not use the oven outdoors.

If the supply cord is damaged, it must be replaced by a Fisher & Paykel authorised technician in order
to avoid hazard.
Before you install the microwave, please ensure that

All the packing materials are removed from the inside of the door.

WARNING: Check the oven for any damage, such as misaligned or bent door, damaged door seals
and sealing surface, broken or loose door hinges, latches and dents inside the cavity or on the door.
Ifthere is any damage, do not operate the oven and contact a Fisher & Paykel authorised technician.

The socket must be readily accessible after installation so that it can be easily unplugged in
anemergency.

The built-in cabinet shall not have a rear wall behind the appliance.

Minimum installation height is 85cm.

Do not cover ventilation slots and air intake points.
5THE BOTTOM CABINET TEMPLATE
Read the instruction on the
BOTTOM CABINET TEMPLATE.
Put the template on the
cabinet’s bottom panel.

9FINISH SECURING OVEN TO CABINET
Open the door.
Fix the oven to
the cabinet with
screw type C at the
installation hole of
trim kit. Then fix the TRIM-KIT
PLASTIC COVER to the INSTALLATION HOLE.
10 FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Has all packaging been removed from the appliance?
Is the appliance securely fastened to the cabinetry?
Does the door open and close properly?
Is the appliance level?
Have the panels been properly aligned for correct operation and appearance?
Are all clearances even?
Has the power cord been plugged into a properly earthed 3-prong outlet, which
has been installed in accordance with all applicable electrical codes?
OPERATION:
Turn the power to the oven on. The display should light up and show 0:00.
Open door, does oven light come on?
Place cup ¾ full of cold water in microwave and set for 30 seconds of operation
by pressing the START/ +30 SEC/CONFIRM button once. After 30seconds is the
water warm?
Have you demonstrated the basic operation to the customer?
Installer’s name:
Installer’s signature:
Installation company:
Date of installation:
LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER
6MARK THE CABINET’S BOTTOM PANEL
AS INDICATED ON THE TEMPLATE
7REMOVE THE TEMPLATE AND FIX THE
BOTTOM BRACKETS WITH SCREW TYPE A
Before you call for service or assistance…
Check the things you can do yourself. Refer to the installation instructions, your User Guide – inparticular
the troubleshooting section and check that:
1
your product is correctly installed
2
you are familiar with its normal operation.
If after checking these points you still need assistance or parts, visit
www.fisherpaykel.com/au/support OR
www.fisherpaykel.com/nz/support for regional service providers.
792003 D NZ AU 06.16
Bracket
Screw A
Centre line
8INSTALL THE OVEN INTO THE CABINET
Bracket
BA
Clearances (mm) OM25BLCX1 model
Aminimum clearance to surrounding cabinetry 5
Bfascia overhang to base panel 5