Fisher-Price DH9060P User manual

INSTALLATION GUIDE
DH9060P & DH9060PG
models
HEAT PUMP CLOTHES DRYER
NZ AU BI

3
SAFETY AND WARNINGS
zKeep all packing materials until the unit has been inspected.
zInspect the product to ensure there is no shipping damage. If any damage is detected
contact the dealer or retailer you bought the product from to report the damage.
zFisher & Paykel is not responsible for shipping damage.
Drain Hose (1) Drain Hose Connector (1)
Drying rack (1) Foam filter (3)
WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the
important safety instructions listed below. Read all the guidance before using the appliance.
Installation
zThe appliance must not be supplied through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on and off by a utility.
zWe do not recommend the use of extension cords or portable electrical outlet devices for
safety reasons.
zThe dryer must be installed in a well-ventilated, dust-free environment.
zThe dryer must not be installed on any textured floor coverings (eg carpet, rugs) to ensure
that openings at the base of the machine are not obstructed.
zDo not install the dryer behind a lockable door, sliding door, or behind a door where the
hinge is on the opposite side to that of the dryer in such a way that the full opening of the
door is inhibited. Ensure the dryer door can always be opened fully.
User guide (1)
USER GUIDE
NZ AU
HEAT PUMP CLOTHES DRYER
DH9060P & DH9060PG
models
SUPPLIED PARTS
!WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electric shock or death.
• If you are using an extension cord
or a portable electrical outlet device
(eg multi-socket outlet box), ensure that it
is positioned so that it does not come into
contact with water or moisture.
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to
change at any time. For current details about model and specification availability in your country,
please go to our website www.fisherpaykel.com or contact your local Fisher&Paykel dealer.

4
PRODUCT DIMENSIONS
FRONT PROFILE
PLAN
Actual product dimensions may vary by ± 2 mm.
A
B
e
D
C
D
C
PRODUCT DIMENSIONS MM
A Overall height* min 840
max 855
B Overall width 600
C Overall depth** 665
D Depth with door open 1080
*Includes adjustable mounted feet and the range of movement
**Includes dial and door when closed

5
CAVITY & CLEARANCE DIMENSIONS
CLEARANCE DIMENSIONS MM
A Minimum door clearance to adjacent wall 335
B Minimum side clearance to adjacent product or cabinetry* 20
*Applies to side, top and rear
FRONT PROFILEISOMETRIC
a
a
c
CAVITY DIMENSIONS MM
A Minimum cavity height 860
B Minimum cavity width 640
C Minimum cavity depth
zFlush with front panel of the product
zIn cupboard
640
705
B
b b
B
b
* Front panel of the product
c
Actual product dimensions may vary by ± 2 mm. For paired installation dimensions, please visit fisherpaykel.com.

6
ELECTRICAL CONNECTION
SPECIFICATIONS
ELECTRICAL
Supply 220 – 240VAC, 50Hz
Service 10-amp circuit
Power consumption (W) 550
Power Cord
1500mm
Drain Hose
1300mm
CONNECTION LOCATIONS / LENGTHS
UNPACKING
1 Remove the outer packaging including the
plastic wrapping.
2 Lift the dryer off the base.
3 Remove all packaging and accessories from inside
the drum.
4 Dispose of all packaging sustainably, ensuring these
materials are kept out of the reach of children.
Actual product dimensions may vary by ± 2 mm.

7
INSTALLATION OPTIONS LEVELLING THE DRYER
Freestanding
The dryer stands on the floor and can easily be
moved into position.
Installation location
zDo not install your dryer in such a way that the dryer door cannot be opened fully.
zDo not install the dryer outside, in a damp place, where there is a risk of freezing, whereit
may be rained on, in direct sunlight or close to a source of heat.
zDo not place your machine on top of its power cable.
Your dryer can be installed one of two ways, either freestanding, or stacked on top ofaFisher
& Paykel front loading washer.
A stacking kit MUST BE USED between the products and
fitted correctly to the washing machine and dryer, as per
the stacking kit instructions.
zEnsure you use the compatible stacking kit for your
washer and dryer combination.
zStacking kit is available from your Fisher&Paykel dealer,
online or from a Fisher & Paykel service technician.
zThe power plug must be accessible.
The following stacking configurations are not safe and
MUST NOT be used:
zA washer stacked on top of a dryer
zA washer on top of a washer
zStacking on top of a washer not listed below
Refer to your stacking compatibility document provided
with your dryer for details of safe stacking options.
For detailed information on install combination and options
please refer to fisherpaykel.com.
Stacked
It is IMPORTANT to level the dryer to ensure the machine runs efficiently with minimal noise. The
dryer should be levelled in as close to its final position as possible so it stands balanced evenly
on all four feet. Ensure the dryer does not rock in any direction.
1
2
3
Level the dryer side to side:
zPlace the level at the centre back of the dryer.
zAdjust the rear feet until the dryer is level
side to side.
zNever unscrew the feet completely from
their housings.
Level the dryer front to back:
zPlace the level on the left side.
zAdjust the front left foot (wind down).
zRepeat the above for the right foot.
zThere should be equal weight on both
front feet.
Re-check the dryer is level:
zPlace the level at the centre front of the dryer.
zEnsure dryer does not rock in any direction.
zIf dryer is not level repeat the above steps.
After levelling, the corners of the dryer cabinet should be clear of the floor andthedryer
must not rock in any direction.

8
The drain hose must be secured in a drain to prevent water draining onto the floor. Ensure
the drain hose is securely fixed in place to an appropriate drain and is leak-free at the
connection to the machine. Check the connection and drain hose regularly.
zMaximum standpipe height is 1.0m from ground level.
zRegularly check that your standpipe or tub is free from lint and other obstructions, which
may affect drainage and cause flooding.
zThe drain hose should be checked from time to time and replaced if any damage, egwear,
cuts, bulges, kinks, leaks, etc is found. Do not bend the drain hose sharply, asthismay
cause it to split.
DRAINING
The dryer is equipped with a condenser unit which accumulates water during the dryingcycle.
This water is either collected in the removable water tank located at the top leftof the dryer,
or you can setup your dryer to drain automatically using the drain hoseprovided.
We recommend the dryer is set up to drain automatically where possible especially when
drying full loads, this will avoid having to empty the water tank during a drying cycle.
In multi-storey apartments or any upper floor, the machine should be installed on
afloorequipped with a drain. Draining must comply with local by-laws.
1
Connecting the drain hose
Remove the black hose from the connection
at the back of the dryer.
Uncoil the drain hose (included with your
dryer) and connect it to the black hose.
Place the other end of the drain hose into a
tub or standpipe.
2
3

9
COMPLETE INSTALLATION
Test cycle
Ensure the test cycle is completed before you dry any items in your dryer. The test cycle is to
check that your dryer is installed correctly and that it is functioning properly prior to use.
1Press POWER to activate your dryer.
3
Press , the drum will start rotating.
Observe the dryer for any problems.
The dryer will beep and display any faults on
the screen. If there are any problems, refer to
your user guide.
At the completion of the cycle, open
the door and check that there is warmth
inside thedryer. This indicates the dryer
is operating normally.
Select the TIME DRY cycle for 30 minutes.
Ensure the drum is empty and the door
isclosed (you will hear it click shut).
2
If there are any problems, you must address these before proceeding with normal use. The
dryer will automatically turn off at the end of the cycle if there are no problems.
zTurn on the water and check all hose connections for leaks. Make sure there are no kinks in
the hose(s). Check the hose connections for leaks again after 24hours.
zUncoil power cord, remove and discard the plastic pin cover, and plug into wall socket.
zConnect the appliance to an earthed outlet protected by a fuse of suitable capacity.
TO BE COMPLETED BY THE INSTALLER
Is the dryer correctly levelled, and are the cabinet corners clear of the floor
and walls?
Is the drain hose attached to the correct outlet and hooked into a standpipe or tub?
Has the water inlet been connected correctly?
Are the water tank, condenser filter, foam filter and lint filter correctly in place?
Has the power cord been connected to an appropriate power supply and the power
turnedon?
Have you performed the test cycle?

10
SPARE PARTS* PART NO.
Drain hose extension (not suitable for attaching to a spigot) 425627P
*Available from your Fisher&Paykel dealer or a Fisher&Paykel trained and supported service technician
SPARE PARTS
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date