Fiskars Momentum User manual

Owner’s Manual
Save this manual for future reference
Momentum™
THE WORLD’S MOST ADVANCED REEL MOWER™
Para ver la versión en español, vaya a la página No. 19.

Fiskars Help Line: 1-877-201-3260 www.skars.com
83001816
Fiskars warrants to the original purchaser that its Lawn Mower products are free from defects in materials and workmanship appearing under normal use within four (4) years after the date of purchase.
This warranty does not cover damage to Lawn Mower products caused by abuse, acts of God, your failure to follow product instructions, mishandling or unauthorized repair. THIS WARRANTY IS IN LIEU
OF ALL OTHER EXPRESS WARRANTIES; AND ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, ARE LIMITED TO THE DURATION OF THIS WARRANTY. IN NO EVENT WILL FISKARS BRANDS, INC. BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states
do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of incidental or consequential damages, so the above limitation and/or the above exclusion may not apply
to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. As its sole responsibility and your sole remedy for any warranted defect, Fiskars
Brands, Inc. will replace any defective part of the Lawn Mower, containing a warranted defect, free of charge, with proof of purchase and notification within a reasonable period of time (but no longer than
6 months) following the discovery of such defect. For warranty service, email warranty@fiskars.com or call 1-877-201-3260.
Questions? Suggestions?
Don’t return to the store. We’re here to help.
Call our customer service team at 1-877-201-3260
Visit our website at www.skars.com
Save this manual for future reference.
LIMITED FOUR YEAR WARRANTY
Momentum™
THE WORLD’S MOST ADVANCED REEL MOWER™
Model Number: 6201
Fill in the following information for easy reference.
Serial Number:________________________________
(located on the lower back portion of the mower)
Date of Purchase:______________________________

Fiskars Help Line: 1-877-201-3260 www.skars.com Fiskars Help Line: 1-877-201-3260 www.skars.com
Table of Contents
Contents:
Safety Information ................................................................................ 2
A Smart Choice ..................................................................................... 3
Momentum® Technologies ................................................................... 4
Mower Anatomy .................................................................................... 5
Assembly ............................................................................................... 6-7
Adjusting Your Mower .......................................................................... 8-9
Checking Cutting Performance ........................................................... 10-11
Using Your Mower ................................................................................. 12-13
Troubleshooting .................................................................................... 14-15
Care and Maintenance ......................................................................... 16-17
Congratulations and Thank You!
Congratulations on your purchase of a Momentum™ reel mower! The design team
at Fiskars has worked hard to make this product the world’s most advanced reel
mower. The result is a reel mower that uses technology and advanced design to
deliver an easier and better way to achieve the simpler, healthier, and greener
mowing experience you desire.
Who We Are
Established in 1649 in a small village in Finland, Fiskars is the second oldest
incorporated entity in the world. Throughout centuries of manufacturing a wide
variety of consumer and industrial products, Fiskars has been continually
committed to the development of reliable and innovative performance-based
products.
What We Believe
By creating the most unique, ergonomic and easy-to-use tools, we provide
garden and outdoor enthusiasts with an enhanced experience. Having received
over 46 international design awards from the world’s most prestigious product
design competitions, each of our garden tools delivers advanced technologies
and superior quality. Our mission is to support and inspire enthusiasts through
continuous innovation and ideas that result in tools that are intuitive, durable and
built to deliver.
Our Other Products
Visit our website at www.fiskars.com to see our full line of products, including
other earth-friendly tools like ergonomic, easy-to-use weeders that provide an
alternative to pesticides, complete rainwater harvesting systems that provide
an easy way to collect, store and dispense rainwater, and eco-friendly pottery
made from by-products of renewable and sustainable materials.

Safety Information
2
Safety Information
Do not use mower if in poor health.
Do not operate with missing or damaged guards.
Always wear safety glasses, gloves and closed-toed shoes when
operating and maintaining your mower.
Never place hands, fingers, or feet in the reel. When the reel is
spinning, it will cut.
Always remove debris from path of mower.
Always have sound footing when using the reel mower, especially on wet
grass or on slopes (inclines).
Use safe lifting practices when moving mower.
Do not allow children under 12 to use mower.
Do not operate around children, other people or pets.
Do not run while using the reel mower.
Do not use mower in areas other than grass.
Make sure your mower is in safe operating condition by following the tips
outlined in this manual.
Do not use this mower if it becomes damaged. Call 1-877-201-3260 or a
qualified repair service.
Before assembling or using the mower, read through the entire
manual and fully understand the safety information.
Fiskars Help Line: 1-877-201-3260 www.skars.com

A Smart Choice
3
Why Are Reel Mowers a Smart Choice?
Reel mowers are good for your lawn. Reel mowers promote greener,
healthier lawns by cutting each blade of grass cleanly with a scissors-like action.
This minimizes moisture loss and exposure to disease. Gas and electric rotary
mowers, on the other hand, stress the grass by cutting with a tearing action
that leaves a jagged edge, making grass susceptible to drying and disease.
Reel mowers also eliminate accidental damage caused by gasoline spills or
dragging extension cords.
Reel mowers are good for your health. Reel mowers let you cut your grass
without exposure to noxious exhaust gases, loud noises, uncomfortable
vibrations or the hazards of power-driven rotary blades – including not just
serious injury, but also damage caused by thrown rocks. Reel mowers also
eliminate the risks associated with storing and handling the gasoline and
oil required by gas mowers and with mowing around the extension cords
required by electric mowers.
Reel mowers are good for the environment. Reel mowers are the most
earth-friendly way to cut your grass. Gas mowers produce dirty exhaust that
pollutes the air. According to the U.S. Environmental Protection Agency (EPA),
the average gas mower produces as much air pollution in one year as a new
car driving more than 500,000 miles. Gas mowers also consume gasoline
and create spills during fueling. The EPA estimates that every year Americans
burn 800 million gallons and spill 17 million gallons of fuel (more than all the oil
spilled by the Exxon Valdez) while maintaining their yards. Electric and battery
mowers, while more earth-friendly than gas mowers, still result in air pollution
– not in your backyard, but at the power plants that produce the electricity on
which the mowers run.
Reel mowers are good for your budget. Reel mowers cost nothing to
operate. There are no gasoline, oil, electricity, spark plugs, or air filters to
purchase. Reel mowers also require far less maintenance than gas and
electric mowers.
Fiskars Help Line: 1-877-201-3260 www.skars.com
Fiskars Help Line: 1-877-201-3260 www.skars.com

Momentum™ Technologies
4
StaySharp™ Cutting System, Fiskars® Exclusive
What is it? Fiskars® exclusive StaySharp™ cutting system uses precision
ground hardened steel blades engineered to efficiently cut grass without
actually touching. To do this, the cutting reel and stationary blade are separated
by about 0.003 inches – less than the thickness of a blade of grass.
How is it different? Standard reel mowers rely on contact between the cutting
reel and stationary blade for cutting. The steel on steel contact that is produced
creates friction and causes blade wear. As a result, the blades on standard
reel mowers dull quickly and require annual sharpening to prevent cutting
performance degradation.
Why is it important? Since Fiskars® StaySharp™ cutting system cuts grass
without the blades touching, friction and blade wear are greatly reduced.
As a result, long lasting performance is maintained without the cost and
inconvenience of annual blade sharpening.
InertiaDrive™ Technology, Patent Pending
What is it? Fiskars® patent pending InertiaDrive™ technology combines a large
diameter cutting reel, heavy cutting reel blades, and a powerful chain drive to
deliver superior cutting power.
How is it different? Standard reel mowers use small diameter cutting reels with
thin blades. These reels and mowers lack cutting power and, thus, frequently
jam when cutting small twigs, weeds, or dense grass. When this happens the
cutting reel seizes, completely stopping the mower. The obstruction must be
removed before mowing can resume.
Why is it important? Fiskars® patent pending, InertiaDrive™ technology uses
the mower’s large diameter cutting reel and heavy blades to store energy (like
a flywheel) until a burst of extra cutting power is needed. When a tough spot is
encountered, the InertiaDrive™ technology delivers twice the energy to power
through it without jamming - providing a superior cut without interruption.
VersaCut™ Design, Patent Pending
What is it? Fiskars® patent pending VersaCut™ design extends the cutting
blades across the entire width of the mower and uses a long wheel base to
optimize blade positioning.
How is it different? Other reel mowers place the two large drive wheels
outside of the cutting reel. This design creates 3" wide no-cut zone under each
wheel, making close edging impossible. It also requires undesirable blade
positioning, limiting both the maximum cut height and range of cut height
adjustment possible.
Why is it important? Fiskars® patent pending, VersaCut™ design provides
versatile cutting for all types of lawns and mowing habits. Inset wheels and
blades that extend all the way across the mower completely eliminate uncut
strips from under the wheels, allowing three times closer edging than other reel
mowers. A long wheel base allows for superior blade positioning, delivering
the greatest cut range of any reel mower – with cut height settings from 1" to 4".
The 4" maximum cut height is vital when you miss a week of mowing.
Fiskars Help Line: 1-877-201-3260 www.skars.com
The World's Most Advanced Reel Mower™ The Fiskars® Momentum™
mower combines patent pending technology with Fiskars exclusive design
features to deliver a reel mower with best-in-class cutting performance for
a superior mowing experience.
30% easier to push Most reel mowers can be difficult to push – especially
in longer grass. The advanced technologies of the Fiskars® Momentum™
mower combine to reduce push force by 30% in long grass.
Fiskars® Ergonomics, Fiskars® Exclusive
The Fiskars® Momentum™ reel mower incorporates a number of best in class
convenience features to enhance your mowing experience. These features
include an ergonomic height adjustable handle with a padded grip, a quick
and easy one-touch cut height adjustment system, and a forward throw grass
discharge chute for mess-free operation.

Fiskars Help Line: 1-877-201-3260 www.skars.com
Mower Anatomy
5
Key Components
Being familiar with the parts and technologies of your
Momentum™ reel mower will make assembly and
maintenance much easier. Review the components
shown on these illustrations and refer to them as
needed when following steps outlined in this manual.
Stationary
blade
Cut height
adjustment
knob
Drive
chain*
Drive
system
cover
Small drive
sprocket*
Large drive
sprocket*
Lifting
handle
Cut height
adjustment
cover
Rear wheels (2)
Grass
discharge
chute
Cutting reel
(with InertiaDrive™
technology)
Front fork
assembly
Cutting reel
blades (5)
Drive
system
lubrication
hole
Front wheels (2)
Ergo
grip
Handle
Handle shroud
Handle bolts (4)
and Handle nuts (4)
Handle
mount pegs
(2)
Rear wheel
bearings
(2)
Cutting reel
bearings*
(2)
Side
plates (2)
Torsion
spring
Locking bolts
(2 per side)
Adjustment
dials (2)
Rear axle
Cotter
pins (2)
Handle
height
adjustment
holes
Fiskars Help Line: 1-877-201-3260 www.skars.com
Front fork assembly
bearings (2)
Reel
carriers (2)
* Located under cover (not visible)

Assembly Assembly
A
B
C
D
E
F
G
6. Align holes in handle sections and shroud (D). Slide a handle bolt (E) through
from the inside, so that the end comes through the hole of the handle shroud.
Repeat for the remaining three handle bolts.
7. Align the hex shaped bolt head with the hex shape cutout in the center
handle section (A), and then hand tighten a handle nut (F) onto the bolt.
Repeat for the remaining three handle nuts.
8. Using a wrench, tighten the four handle nuts (F) until they are snug. Do not
over tighten or permanent damage to the handle may result.
Handle Assembly
1. The only tool required for assembly is a 11 mm wrench or socket.
2. Lay out the handle parts as shown above. Note the center handle section
(A) is symmetrical.
3. Insert the free ends of the upper handle section (B) into the center handle
section (A), making sure the arch of the upper handle section is down. Roughly
align the holes.
4. Insert the two lower handle sections (C) into the center handle section (A),
making sure the pointed ends of the lower handle sections are up as shown.
Roughly align the holes.
5. Slide handle shroud (D) into place from below with the Fiskars logo facing
down and towards the upper handle section (B).
6 Fiskars Help Line: 1-877-201-3260 www.skars.com
The following parts are
included in the hardware bag:
Handle nuts (4)
Handle bolts (4)
Cut height adjustment knob (1)

Fiskars Help Line: 1-877-201-3260 www.skars.com
Cut Height Adjustment Assembly
1. Check the front of the cutting reel for a clear thin plastic shipping shield that
extends downward from the grass discharge chute. If the shield is present,
remove and discard it prior to first use.
2. Screw the cut height adjustment knob (G) tightly onto the exposed lever (H)
by hand.
Attaching the Handle
1. Remove the two cotter pins (I) from the handle mount pegs (J).
2. Slide hole number 3 (K) of the handle onto the handle mount pegs (J) and
then release the handle until it rests on the handle stop peg (L).
3. Insert the cotter pins (I) to secure the handle into place.
Assembly
7
G
H
K
L
Attaches
to inside of
frame
Attaches
to outside of
frame
I
J
Fiskars Help Line: 1-877-201-3260 www.skars.com
J
I
L
K
K
J
I

Adjusting Your Mower
8
HINT:
Cut Height Adjustment
Facing the front of the mower, place your right hand on the lifting handle
(A) to support the mower during adjustment. Use your left hand to pull
the cut height adjustment knob (B) away from the mower and move to
your desired cut height. Then release the knob making sure the lever
(C) snaps back into place.
A
B
C
Handle Height Adjustment
1. Before adjusting the handle height it is important to set the mower to the cut
height that you will use most frequently. (See hint to left.)
2. Push the mower forward several feet then turn it around as you would at
the end of a mowing run. If you can push the mower comfortably without
the front end rising and if you can turn the mower without hunching over, you
have the handle set properly.
• If the front end rises, you have the handle set too high. Lower the handle
by using hole 2 for a slight adjustment or hole 1 for a greater adjustment.
• If you have to hunch over a great deal to turn, you have the handle set
too low. Raise the handle by using hole 4.
3. As the cut height is adjusted, the handle's bottom position will also move.
Consequently, you may need to adjust the handle height if you drastically
change the cut height. Adjustment may also be needed if you share mowing
duties with someone else.
1"
4"
Length of grass
after cutting
(cut height)
Fiskars Help Line: 1-877-201-3260 www.skars.com
IMPORTANT: To maximize comfort and control your mower
features a height adjustable handle. The handle is designed to
"oat" between its bottom and in-use positions. The bottom position is
used to pivot through turns. The in-use position should be 6 " to 10"
above the bottom position. Lifting the handle in this fashion keeps
the front end from rising off the ground to ensure an even cut. Since
selecting the correct handle height is extremely important, it is
worth the trial and error that may be required to nd the ideal height.

Adjusting Your Mower
9
6" to 10" Float
In-use position
Bottom position
Storage position
Fiskars Help Line: 1-877-201-3260 www.skars.com Fiskars Help Line: 1-877-201-3260 www.skars.com

Checking Cutting Performance
10
Preparation
1. You’ll need several 1" wide strips of standard printer paper (not news-
paper) about 8" long, a pair of work gloves and a wood block.
WARNING: The mower blades are sharp. Wear gloves when performing
this procedure, and keep fingers away from the interface between the reel
and stationary blade.
2. Ensure that the mower cannot roll forward by positioning it on a firm, level
surface with a block in front of the rear wheels. Then raise the mower to the
highest cut height position to improve access.
Check #1: Do the Blades Make Contact?
1. To check if the blades make contact, face the front of the mower and
slowly pull the cutting reel (A) downward, one blade at a time, through a full
rotation or two. If you hear scraping or feel resistance, skip the remainder
of this section and proceed to Adjusting the Blades on page 11.
ATTENTION: If the cutting reel and stationary blade make contact the
mower will be difficult to push and may dull the blade.
Check #2: Do the Blades Cut Properly?
1. To check if the blades cut properly you will need to check the blades on
both the left and right side of the mower. On the left side, feed a strip of
paper up vertically from under the mower between a cutting reel blade (A)
and the stationary blade (B). About half an inch of the strip should be visible
above the stationary blade.
Fiskars Help Line: 1-877-201-3260 www.skars.com Fiskars Help Line: 1-877-201-3260 www.skars.com
IMPORTANT: The StaySharp™ cutting system is engineered to cut
grass without contact between the blades. This cutting system was
precision set during assembly. However, since slippage may possibly
occur during shipping, handling, or use, it is very important to check the
cutting performance prior to rst use and periodically thereafter. Since
slippage can occur in two directions, two checks are required to evaluate
cutting performance – both checks need to be performed on both the
left and right sides of the mower. Checking the cutting performance,
and adjusting if needed, are the most important things you can do
to ensure that your mower always performs optimally.
A B
IMPORTANT:
Always place the
strip of paper straight
up and down, perpen-
dicular to the ground,
like a blade of grass.
A
B

Checking Cutting Performance
11
WARNING: Keep your fingers away from the cutting region; they should
be below the stationary blade.
2. Pull the cutting reel (A) downward observing whether the paper is cut as the
first cutting reel blade passes.
3. Slide the paper up a half an inch at a time to check the other blades.
4. Move to the right side of the mower and check if the blades cut on that side
properly.
5. If most of the blades cut on both sides, the cutting system is set correctly.
If most of the blades do not cut, the cutting system needs to be adjusted.
Proceed to Adjusting the Blades below.
ATTENTION: Failure to correct an improperly set cutting system will result in
poor cutting performance by leaving uncut blades of grass.
Adjusting the Blades
Adjust the blades as needed. If issues exist on both sides of the mower,
address them one side at a time.
1. The only tool required is an 11 mm wrench.
2. Loosen the two locking bolts on the side you're correcting (C) approximately
one full turn to allow for adjustment.
3. Adjust the blades using the adjustment dial (D) on the appropriate side. Note:
the nut below the dial will move during adjustment.
• If the blades are making contact, turn the dial counter-clockwise while
rotating the cutting reel, stopping as soon as the blades lose contact.
• If the blades didn't cut paper, turn the dial clockwise while rotating
the cutting reel just until the blades make contact. Then turn the dial
counter-clockwise to back off slightly.
4. When properly adjusted, the cutting reel and stationary blade should
be just short of making contact. When the blades are properly adjusted,
C
D
firmly tighten the locking bolts on the side you adjusted. Confirm the
cutting performance has been corrected on this side by once again
performing the two checks. If issues exist on the other side of the mower,
repeat adjustment steps.
Fiskars Help Line: 1-877-201-3260 www.skars.com Fiskars Help Line: 1-877-201-3260 www.skars.com

12
Using Your Mower
Your Momentum™ mower has been designed and engineered to deliver
best-in-class cutting performance and a superior mowing experience.
However, there are several basic things you can do when mowing that
will greatly impact both your mower’s performance and your mowing
experience. If you have used a reel mower before, you will immediately
appreciate the advantages produced by the Momentum™ mower’s
advanced cutting technologies and design features. If this is your
rst reel mower, you will likely require a short transition period as you
adjust your mowing habits to maximize efficiency and effectiveness. The
information below will help both experienced and new reel mower
users achieve all the benets of the Momentum™ mower. Also,
remember that Fiskars customer service team and website are both
available for you should you need additional help.
To maximize cutting power, walk briskly. The cutting power of
the InertiaDrive™ cutting reel increases with the speed of the mower. This
means that the faster you walk, the better your mower will cut. While it is not
necessary to run, if you’re used to mowing at a very leisurely pace, try
walking just a little more quickly.
For efficient mowing, cut your lawn in long, straight lines. Since reel
mowers only cut grass when they are moving, lay out your mowing pattern
to maximize the amount of long, straight runs and to minimize starts and
stops. Overlapping wheel tracks will ensure a complete and uniform cut.
(See figure.)
Precut a turnaround zone to ease turns against obstructions. If any
mowing runs end against an obstruction (garden, foundation, fence, etc.),
begin by making one or two mowing passes along the obstructions to
provide a turnaround zone.
For closest edging, use the left side of the mower. To edge closely against
gardens, foundations, fences, and other barriers, use a mowing pattern that
positions the left side of the mower toward the barrier.
Fiskars Help Line: 1-877-201-3260 www.skars.com
Mowing Tips
For a healthy lawn, cut off no more than 1/3 of the grass length. To
maintain a healthy lawn and eliminate the mess created by very long grass
clippings, cut off no more than one-third of the grass length at a time. If more
than one-third of the length is removed, root growth will be impaired and
the grass will be stressed making your lawn susceptible to weed invasion,
disease, and poor appearance. If your lawn gets too high, cut off one third of
the length, wait a couple days, and then cut off another third.
To prevent mower damage, clear the mowing area of debris in advance.
Before starting, inspect the area to be mowed and remove stones, medium-
sized or larger sticks, trash, and other debris.
If you hit hard debris, stop and inspect the blades. If you strike a stone,
large stick, or other hard object with the cutting blades, stop mowing
immediately and check for a jam or damage. If the blades are damaged,
pull the mower backwards to an appropriate work area and follow the
instructions in Care and Maintenance on page 16. Continuing to mow with
damaged blades may make repair impossible.

13
Using Your Mower
Safety Information
Do not use mower if in poor health.
Do not operate with missing or damaged guards.
Always wear safety glasses, gloves and closed-toed shoes when
operating and maintaining your mower.
Never place hands, fingers, or feet in the reel. When the reel is
spinning, it will cut.
Always remove debris from path of mower.
Always have sound footing when using the reel mower, especially on
wet grass or on slopes (inclines).
Use safe lifting practices when moving mower.
Do not allow children under 12 to use mower.
Do not operate around children, other people or pets.
Do not run while using the reel mower.
Do not use mower in areas other than grass.
Make sure your mower is in safe operating condition by following the
tips outlined in this manual.
Do not use this mower if it becomes damaged. Call 1-877-201-3260
or a qualified repair service.
Edging and turnaround zone cutting
General mowing
Fiskars Help Line: 1-877-201-3260 www.skars.com
Fiskars Help Line: 1-877-201-3260 www.skars.com

Your Momentum™ mower combines patent pending technology with
Fiskars exclusive design features to deliver best-in-class cutting
performance and a superior mowing experience. The mower is
designed to provide long lasting performance with only simple care
and maintenance (see next section). If you experience problems using
your mower, the information below will help you investigate possible
causes, then x the problem. Also, remember the Fiskars customer
service team and website are both available for you should you need
additional help.
14
Troubleshooting
Problem: The mower is hard to push or the reel doesn’t
spin freely.
Are you trying to cut too much grass? While the Momentum™ mower has
more cutting power than any other reel mower, the mower may become hard to
push or even clog if the cut height is set too low for the length of the grass being
cut. If this is the case, readjust the cut height so that you are cutting no more than
1/3 of the length of the grass.
Is the mower awkward to push? Your Momentum™ mower features an
ergonomic height adjustable handle for maximum comfort and control. If the
adjustable handle is set too high, it may feel awkward while pushing. Try
setting the handle at the next lowest setting. Refer to Adjusting Your Mower on
page 8.
Is the drive train obstructed? Your Momentum™ mower is designed to be
easier to push than other reel mowers – especially in longer grass. If you find
that your mower becomes harder to push, examine the ends of the reel and
the wheels to see if grass clippings or other debris has created a jam. If an
obstruction is present, clear it with a long bristled brush or soft tool.
Are the blades making contact? While your mower's cutting system was
precision set during assembly, it is possible that some slippage may occur during
shipping, handling, and operation. To check if the cutting gap is set properly,
refer to Checking Cutting Performance on page 10.
Problem: Turning the mower is difficult or requires stooping.
Is the handle height set properly? Your Momentum™ mower features an
ergonomic height adjustable handle for maximum comfort and control. If the
adjustable handle is set too low, turning the mower may require you to stoop
over. If this happens, refer to Adjusting Your Mower on page 8 for instructions on
raising the handle.
Fiskars Help Line: 1-877-201-3260 www.skars.com
Problem: The mower leaves some uncut blades of grass.
Is your grass very long or are tall weeds present? While the Momentum™
mower can cut grass higher than any other reel mower and has more
cutting power, if grass over 6" long or tall weeds are present, they may be
knocked down by the mower’s front fork assembly. If this happens, either pull
these long stragglers by hand or make a second mowing pass to try and cut
them. To prevent this entirely, never let your grass grow longer than 6".
Does the front of the mower rise off the ground? Your Momentum™ mower
features an ergonomic height adjustable handle for maximum comfort and
control. If the adjustable handle is set too high, the force you exert when
pushing the mower may cause the front wheels to rise up off the ground,
resulting in uneven cutting. If this happens, refer to Adjusting Your Mower on
page 8.
Are the blades set improperly? While your mower's cutting system was
precision set during assembly, it is possible that some slippage may occur
during shipping, handling, and operation. To check if the cutting system is set
properly, refer to Checking Cutting Performance on page 10.

15
Troubleshooting
Questions? Suggestions?
Don’t return to the store. We’re here to help.
Call our customer service team at 1-877-201-3260
Visit our website at www.skars.com
Problem: The mower makes a scraping or tinging noise.
Does the drive chain need to be lubricated? Your Momentum™ mower
features a powerful chain drive. The chain itself is similar to the chain on
a bicycle, and like a bicycle chain may make a noise or become hard to
move when rusted or in need of lubrication. To fix this problem, lubricate the
chain through the access hole in the chain cover as described in Care and
Maintenance on page 16.
Is the cutting reel or stationary blade damaged? While the Momentum™
mower has hardened blades, blade damage can still occur if rocks, concrete
edges or other hard debris are struck. If this happens, the damaged area of
the blade may cause a high-pitched sound when it passes the other blade.
See General Maintenance on page 16 for additional details.
Are the blades making contact? While your mower's cutting system was
precision set during assembly, it is possible that some slippage may occur during
shipping, handling, and operation. To check if the cutting gap is set properly,
refer to Checking Cutting Performance on page 10.
Problem: The cutting reel remains stationary when the mower
is pushed forward.
Did the drive chain come off? Your Momentum™ mower features a powerful
chain drive system. The drive system consists of a chain and two sprockets,
similar to those found on a bicycle. While unlikely, slippage during shipping,
handling, or operation may cause the drive chain to come off or a drive sprock-
et to loosen. To investigate either condition, use a 10 mm wrench or socket to
remove the drive system cover by removing the two bolts that hold it in place.
If the chain is off one or both sprockets, use a 5 mm Allen wrench to remove
the front sprocket’s set screw and then the sprocket itself. Place the chain on
the sprocket, and then replace both the sprocket and the drive system cover.
Did a drive sprocket loosen? If the chain is on both drive sprockets, with your
hands safely away from the cutting reel, roll the mower forward and observe
both sprockets. If both sprockets turn, the small drive sprocket has come loose.
If neither sprocket turns, the large drive sprocket has come loose. To tighten
either sprocket, first remove the set screw from that sprocket completely with
a 5 mm Allen wrench. After aligning the holes in the sprocket and the shaft,
replace and tighten the set screw. Use thread locking fluid if you have it.
Then replace the drive system cover. If the set screw is missing, call
1-877-201-3260 for a replacement.
Fiskars Help Line: 1-877-201-3260 www.skars.com
Fiskars Help Line: 1-877-201-3260 www.skars.com

Care and Maintenance
IMPORTANT: Your Momentum™ reel mower is a precision cutting
instrument, manufactured to exacting specications. It is designed
to deliver superior cutting performance for many years, but can be
damaged if mistreated. To ensure long lasting performance, protect
your mower from impact during use and storage, keep it clean and dry,
and practice regular maintenance as follows.
Drive Chain (A): Spray lubricant through the drive system lubrication hole
while slowly rolling the mower forward to move the chain.
Rear Wheel Bearings (B): Spray lubricant between each wheel and side plate.
Cutting Reel Bearings (C): Spray lubricant on both ends of the cutting reel shaft,
which is located under the grass discharge chute (D).
Front Fork Assembly (E): Spray lubricant on both ends.
Cut Height Adjustment Lever (F): Spray lubricant on the cut height adjustment
lever through the slot in the cover (G).
16 Fiskars Help Line: 1-877-201-3260 www.skars.com
General Maintenance
Keep your mower dry to prevent rust. Your Momentum™ mower will
perform better for longer if it is kept dry. The precision ground blade
edges of the cutting reel and stationary blade and the bearings that carry the
cutting reel and the rear axle are most vulnerable to rust. If your mower does
get wet, dry it off with a towel and then spray it with a rust preventative as
soon as possible.
ATTENTION: Do not use solvents such as mineral spirits or kerosene to
clean your reel mower. They will damage the plastic.
Keep your mower clean to eliminate potential jams and moisture that
could cause rust. Your Momentum™ mower will last longer and look better
if it is kept clean. After mowing, use a broom or long-bristled brush to clean
any grass clippings or other loose debris from the mower – especially around
the cutting reel and the bottom of the drive system cover. Removing grass
clippings prevents cutting and drive system jams and eliminates trapped
moisture that could cause rust.
ATTENTION: Do not use a garden hose to wash your mower. Storing the
mower wet will allow rust to form.
Lubricate moving parts at least once a season and prior to winter
storage to maintain peak performance. Your Momentum™ mower will push
easier and last longer if all moving parts are lubricated periodically. It is also
recommended that lubrication be applied any time the mower gets wet.
BB
EE
A
F
CC
D
G

Fiskars Help Line: 1-877-201-3260 www.skars.com
Care and Maintenance
17
Inspect your blades at least once a season and anytime your mower
strikes a hard object. While your Momentum™ mower features the Fiskars®
exclusive StaySharp™ cutting system with hardened steel blades, blade
damage may still occur if rocks, concrete edges or other hard debris are
struck. Before checking for blade damage, ensure that the mower cannot
roll forward by positioning it on a firm, level surface with blocked rear wheels.
Examine the entire length of the ground edges on all five cutting reel blades
and the stationary blade. If a dent or ding is found, determine if the ding
causes the cutting reel and stationary blade to touch. To do this, slowly pull the
cutting reel downward while listening for scraping and feeling for resistance
in the area of the ding. If there is no contact, there is no need to repair
the ding. Simply treat it with rust preventative and re-inspect periodically in
case raised edges appear with continued use.
WARNING: The mower blades are sharp. Wear gloves when performing
this procedure, and keep fingers away from the interface between the reel
and stationary blade.
To avoid further damage, repair any ding that causes the cutting
reel and stationary blade to touch as quickly as possible. With care,
any ding found can be repaired with little or no impact on your mower’s
cutting performance. Before beginning, get a narrow fine file (like the one
found in the Fiskars® Model 7862 - Tool Care Kit) and position the mower
on a firm, level surface with blocked rear wheels to ensure that it cannot
roll forward. To remove the ding, file away only
enough of the raised material to allow the cutting
reel to spin without making contact with the
stationary blade. File with long, straight strokes
perpendicular to the cutting edge of the blade,
trying to avoid removing material from the
cutting edge itself. When the raised edges are
filed down, check the cutting gap as described
in Checking Cutting Performance on page 10.
WARNING: The mower blades are sharp. Wear gloves when performing
this procedure, and keep fingers away from the interface between reel and
stationary blade.
ATTENTION: Do not use a power tool to repair blades. Too much steel will
be removed, resulting in severe blade damage and greatly reduced cutting
performance.
When blades need to be sharpened, seek out a professional with
appropriate sharpening equipment. Fiskars’ StaySharp™ cutting system
is precision engineered to cut grass without contact between the blades
– greatly reducing friction and blade wear. As a result, long lasting
performance can be maintained without the cost and inconvenience of
annual blade sharpening. In fact, with proper care, your Momentum™
mower should not require sharpening at all. If, however, after many years
of use, the blades do need to be sharpened, the job should be performed
by a professional with appropriate reel mower sharpening equipment. The
cutting reel and stationary blade on your Momentum™ mower were factory
sharpened on state-of-the-art automated equipment. The shape and
uniformity of the grinds are impossible to replicate by hand, and attempting
to do so will degrade the performance of the mower.
ATTENTION: Since the blades on the Fiskars’ exclusive StaySharp™ cutting
system are substantially harder than those on standard reel mowers, the
traditional method of lapping the blades with abrasive compound will not
work and will likely diminish the mower’s cutting performance.
Fiskars Help Line: 1-877-201-3260 www.skars.com