Flair COMPTON METAL BED User manual

Please read this sheet prior to assembly to familiarise yourself with the various stage
of construction. Carefully open the pack supplied and check the content against the
parts and fitting check list. Do not destroy any of the packing until you are certain
that you have all the necessary part for assembly.If for any reason you need to
return this item, you must return it in its original packaging.
Assembled items cannot be returned.
PLACE ALL PARTS ON A CLEAN AND SMOOTH SURFACE SUCH AS A RUG OR
BEFORE YOU BEGIN, KINDLY FOLLOW THE ASSEMBLY INSTRUCTIONS STEP
DO NOT TIGHEN ALL SCREWS UNTIL THE BED IS FULLY SET-UP.
IMPORTANT NOTE:
1/4
ASSEMBLY INSTRUCTIONS
“COMPTON METAL BED”
CARPET TO AVOID THE PARTS BEING SCRATCHED.
BY STEP.
SIZE: SINGLE, SMALL DOUBLE, DOUBLE & KING

Important Information
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
Due to the size of this product we recommend that it is assembled in the room intended for use.
When you are ready to start, make sure that you have the right tools, plenty of space and a
clean, dry area for assembly.
Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent it from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled and secured as illustrated before use.
Check all screws or bolts are tightened and inspect regularly.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Make sure the legs remain in contact with the ground.
Tools are included.
WARNINGS
Do not place bed near heat sources, windows or other furniture, This includes danger of blind
cords, curtain pulls, other strings or cords.
This product is intended for a maximun person's weight of 100kg per side. Do not exceed this
weight.
Children can be trapped between the bed and the wall. To avoid risk of serious injury the bed
should be placed tight to the wall or have a gap of 300mm from the side of the bed to the wall.
Do not use the bed if any part is broken, torn or missing.
Not suitable for children under 4 years old.
Do not use power tools to construct this product.
Do not tighten screws until fully assembled.
Do not over tighten screws or bolts.
Do not stand on the product.
Please pay particular attention when children or animals to ensure that no accidental
entrapment occurs whilst operating this product.
CARE INFORMATION
Never use scourers, abrasives or chemical cleaners.
To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or
detergents as they can bleach or damage the product.
2 Person Build
2/4

3/4
LIST OF PARTS
1
HEADBOARD
1 PC
2
FOOTBOARD
1 PC
SIDE RAIL
2 PCS
3 4
END RAIL
5
2 PCS
6
CENTRE RAIL
(2 PCS EV PAD STICK
UNDERNEATH)
7
1 PC
8
LIST OF HARDWARE
A
M6*15mm
BOLT
20 PCS
B
M6*40mm
BOLT
4 PCS
2 PCS
9
HORIZONTAL
SUPPORT RAIL WOODEN SLAT END SLAT CAPS CENTRE SLATS CAPS
28 PCS
(SINGLE / SMALL DOUBLE / DOUBLE)
32 PCS
(KING)
28 PCS
(SINGLE / SMALL DOUBLE / DOUBLE)
32 PCS
(KING)
14 PCS
(SINGLE / SMALL DOUBLE / DOUBLE)
16 PCS
(KING)
STEP 1
C
4 PCS
"T" NUT
D
1 PC
M4 ALLEN KEY
10
EV PAD
4 PCS
A
8 PCS
D
1 PC
Please link to 4 point same
assembly.

STEP 2
4/4
STEP 3
8
7
9
7
8
i:
ii:
i:
A
A
3
3
1
2
5
4
4
6
6
A
12 PCS
B
4 PCS
C
4 PCS
D
1 PC
ii:
4
iii:
A
A
3
3
1
2
PART 5:
2 PCS EV PAD STICK
UNDERNEATH
(To avoid any direct friction
on Part 5 & 6)