FLI Audio FU720.4-F1 Parts list manual

лчиттничюнльтцию.
глтчн.Бзвыдны
www.sotmarket.ru
дбняинфмциятв,
тзывы,бзыиы
Инструкция для
FLI Underground FU720.4-F1
Перейти в карточку товара
8 800 775 98 98

UNDERGROUND
INSTRUCTION &
INSTALLATION MANUAL
MODEL: FU720.4
AMPLIFIER
FU720.4

INTRODUCTION
This instruction manual is for your safety and must be adhered to at all times. Please read
and ensure that you fully understand the installation and set up procedures as explained.
If you are unclear on the installation or set up of your FLI UNDERGROUND amplifier please
contact your nearest authorised FLI UNDERGROUND dealer.
Thank you for purchasing this FLI UNDERGROUND amplifier. It will provide you
with years of trouble free usage providing you follow a few simple guidelines.
2
WARNING
DO NOT EXPOSE THIS PRODUCT TO DAMP OR MOISTURE - doing so may result in fire,
shock or damage to the product.
BEFORE WIRING DISCONNECT THE CABLE FROM THE POSITIVE BATTERY TERMINAL
- failure to do so may result in electric shock or injury.
ENSURE GOOD AND CORRECT CONNECTIONS - failure to make the correct connections
may result in fire or damage to the product.
KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE - failure to do
this may result in an accident. FLI UNDERGROUND equipment is capable of producing sound
levels that can permanently damage your hearing. FLI UNDERGROUND recommends caution
when listening at high volume. For safe and enjoyable listening the sound should be comfortable
and clear without distortion.
CAUTION
• Never connect any speaker lead to the car chassis. This can cause severe damage to your
speaker / car radio / amplifier.
• Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.
• Use caution when working near the fuel / hydraulic lines and electrical wiring.
• Observe the correct polarity when wiring, improper phasing may cause a loss of bass
response.
• Ensure that no moving parts catch on the speaker or grill (e.g. window or door handles, or
window glass inside the door)
INSTALLATION
• The quality of the installation will affect the system performance and reliability.
• Contact your nearest authorised FLI dealer if you are unsure about the installation of this
product.
• Please mount this unit away from any potential hazards.
• Minimising the length of wires will provide higher audio output from the system.
• The speaker should be securely fastened to the mounting position using the screws
provided.
• Pre drill your mounting holes using a drill and position with the template provided.
• Be sure to investigate your mounting area thoroughly for electrical wires, brake or fuel lines or
fuel tank to prevent causing any damage.
BLE F
ock or injur
ONNECTIONS
-
roduct.
L SO YOU CAN STILL HE
LI UNDERGROUND equipme
amage your hearing. FLI UNDER
e. For safe and enjoyable listening th
speaker lead to the car chassis. This can cause
o / amplifi
cutting any holes, investigate the layout of your vehicle
hen working near the fuel / hydraulic lines and electrical wirin
correct polarity when wiring, improper phasing may cause
at no moving parts catch on the speaker or grill (e.g. window or do
glass ins
TALLA
e quality
ontact your nearest authorised FLI dealer if you are unsure about the installation o
product.
Please mount this unit away from any potential hazards.
the system
aler if
RGROUND
r hearing.
d enjoyabl
car chas
tigate th
/ hydrau
ing, im

3
AMplifier Installation
Your FLI UNDERGROUND amplifier is designed with a swift installation routine in
mind. Please mount the amplifier in a dry location on a solid surface. NEVER mount the
amplifier upside down, this will cause the amplifier to over heat and will eventually damage
the amplifier. Before fixing the amplifier in place please ensure that there is sufficient air
flow around the exterior of the casing, at least two inches will be sufficient.
Power Cable
• At least an 8 gauge cable should be used for both the power and the ground connections to the
amplifier.
• The power cable should be taken directly from the battery. Rubber grommets should be used
when passing through any bulkheads to prevent the cable from becoming chaffed or cut.
• It is vital that a fuse / circuit breaker (of at least equal value to the one fitted on the amplifier) is placed
in line with the power cable and is no further than eighteen inches away from the battery.
• Please ensure that the fuse is not fitted until the entire installation procedure is complete.
• The two tables below are to help you decide on what cable is correct for you. The first enables you to
select the size of cable depending on the length required. The second will help you convert the cable size
from American Wire Gauge to Metric if you need to.
L
en
g
t
h
of
Run
Cu
rr
e
n
t
de
m
an
d
0
–
4
F
t
4
–
7
F
t
7
–
1
0
F
t
1
0
–
1
3
F
t
1
3
–
1
6
F
t
1
6
–
1
9
F
t
1
9
–
22
F
t
22
–
2
8
Ft
0
–20
amp
s
14
1
2
1
2
1
0
1
0
8
8
8
20
–
35
am
p
s
1
2
1
0
8
8
6
6
6
4
35
–
50
am
p
s
1
0
8
8
6
4
4
4
4
50
–
65
amp
s
8
8
6
4
4
4
4
2
65
–
85
amp
s
6
6
4
4
2
2
2
0
8
5–10
5
amp
s
6
6
4
2
2
2
2
0
105
–
125
a
mp
s
4 4 4
2
0
0
0
0
12
5
–1
50
amp
s
2
2
2
0
0
0
0
0
A
WG
AA
t
o
Me
tr
ic
C
onversio
n
C
har
t
cross
sec
ti
o
n
a
l
area
A
WG
AA
Nu
m
be
r
I
n
c
h
m
m
mm
2
0
0
.
3
2
5
8
.25
53
.
5
1
0
.2
89
7.
35
42.4
2
0
.2
58
6
.
54
33
.
6
3
0
.22
9
5
.8
3
26.
7
4
0
.2
04
5
.1
9
21.1
5
0
.1
82
4.
62
1
6
.
8
6
0
.
162
4
.
1
1
13
.
3
7
0
.14
4
3
.
66
1
0
.
5
8
0
.12
8
3
.2
6
8
.
36
9
0
.
1
14
2
.
91
6
.
63
1
0
0
.10
2
2.5
9
5
.26
1M
e
tr
e
–
3
.2
8
F
ee
t

4
ground cable
• The ground cable needs to carry the same current as the power cable. At least an 8
gauge cable should be used.
• The amplifier ground should be connected directly to the chassis of the vehicle, to bare
metal.
• The cable length should be kept to an absolute minimum. It is not recommended that you
connect the ground cable to the vehicle’s seatbelt anchor point.
Remote Turn On
• A minimum of 18 gauge cable should be used for this connection.
• The cable should be run with exactly the same care and attention as the power cable and taken
back to the source (headunit) and joined to the remote cable provided.
• If the source (headunit) does not have a remote turn on cable then a 12v supply should be used. This
will require a switch to be fitted inline to enable the amplifier to be turned on and off. Remember that if
this switch is left on you will flatten the car battery.
RCA Cables
• Depending on the model number of your amplifier and the number of speakers you wish to power you will
have to run either one or two RCA cables from the source to the amplifier.
• Please take extra care when running these cables from the source to the amplifier. Ensure that they are
placed away from all items that can generate any interference, wiring harnesses etc.
• It is recommended that the RCA cables should be run on the opposite site of the car to the previously
installed power cables, if possible.
AMPLIFIER CONNECTIONS & CONTROLS
A. LOW LEVEL INPUT
Low level input for connection to any source (headunit) with a low level output. This is your RCA
output from the source (headunit).
B. GAIN CONTROL
Used to match the input signal of the source (headunit) to the amplifier. There are separate gain
controls for channels 1 & 2 (front) and 3 & 4 (rear). See the setup section for more details.
C. CROSS OVER SELECT SWITCH
Used to select between high pass filter and full range output (channel 1 & 2) or low pass
G H
AB
C E
F
J
BC D
ID

5
filter and full range output (channels 3 & 4). The high pass filter will only allow high
frequency information to be passed to the speaker(s) whilst the full range output will
pass all frequencies to the speaker(s). Similarly the low pass filter will only allow low
frequency information to be passed to the speaker(s).
D. CROSS OVER FREQUENCY CONTROL
The HPF control specifies which frequencies above the set level will be heard (channel 1 &
2). The LPF control specifies which frequencies below the set level will be heard (channel 3 &
4). The frequency ranges from 50hz to 300 Hz.
E. BASS BOOST CONTROL
To provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output
from the amplifier.
F. SPEAKER TERMINAL OUTPUT
For connection to the speakers. See system wiring overleaf for wiring examples.
G . FUSE
Please ensure the following fuse rating is used when replacing fuses:
FLI UNDERGROUND 720.4 (25 amp x 2)
H. POWER CONNECTIONS
Power connections. See overleaf for details on correct connections.
I. POWER PROTECT LIGHT
When the amplifier is operating correctly the light will illuminate constant ‘green’. When the amplifier is in
power protection mode the light will illuminate ‘red’.
Set Up Section
To correctly set the gain control of the amplifier to match that of the source (headunit) use the following setup
routine:
• Turn the gain control to minimum on the amplifier.
• Ensure the bass boost is set to 0 dB.
• On the headunit set all crossovers to flat and both bass and treble to zero.
• Turn up the source (headunit) to approx 3/4 volume.
• Very slowly turn up the gain on the amplifier until distortion can be heard in any of the speakers or until the
volume reaches an uncomfortable listening level when this is reached turn down the gain control slightly.
• The gain control is now set.
The setting of the crossover will depend on what kind of speaker you are installing. For a subwoofer it is
recommended that the crossover select switch is set to low pass and the frequency is set to match that of the
speaker specifications. For a pair of full range speakers it is recommend that the crossover is set to full. The
LPF frequency control will then have no effect on the amplifier output and the speaker will receive a full range
signal.
NOTE: BY USING THE CROSSOVERS CORRECTLY YOU WILL NOT ONLY LENGTHEN THE LIFE
OF YOUR SPEAKERS BUT WILL ALSO GET BETTER PERFORMANCE FROM THEM. TO OPTIMISE
YOUR SETUP SEEK THE ADVISE OF A PROFESSIONAL INSTALLATION ENGINEER OR VISIT YOUR
LOCAL FLI AUDIO DEALER.

6
System Wiring
Input connections
High level input
When using a high level speaker input, use the supplied high to low level converter loom.
BATTERY
FUSE
Connect to
chassis / ground
of vehicle
SOURCE (HEAD UNIT)
Connect to remote turn-on
lead of source unit
SOURCE (HEAD UNIT)
High to
Low Level
converter
L+ WHITE
L- WHITE/BLACK
R+ GREY
R- GREY/BLACK
RL+ GREEN
RL- GREEN/BLACK
RR+ PURPLE
RR- PURPLE/BLACK

7
System Wiring
4 Channel Stereo
System Wiring
2 Channel Stereo, Bridged (mono)
MIN. 2Ω
MIN. 2Ω
MIN. 2Ω
MIN. 4Ω
+
- +
-
+
- +
-
+
-+
-
+-

8
Troubleshooting
Before removing the amplifier, refer to the list below and follow the suggested
procedure. Always test the speakers and confirm that they are wired correctly first. If in
any doubt get help from a qualified auto electrician.
AMPLIFIER WILL NOT POWER UP
• Check for good ground connections. Ensure that the ground cable is connected directly to
bare metal and not a painted surface.
• Using a multimeter check the that remote terminal has at least 7V DC.
• Using a multimeter check that there is battery voltage on the positive terminal.
• Check all fuses.
• Check that the protection light is not illuminated. If it is lit, shut off the amplifier for thirty seconds
and then turn it back on.
PROTECTION LED ILLUMINATES WHEN AMPLIFIER IS POWERED UP
• Check for shorts on all speakers wires. (i.e no speaker wires should be joined together and no speaker
wires should be touching the car’s chassis)
• The amplifier is designed to shut down automatically when the units temperature goes above 80 degrees.
If the amplifier feels very hot then this may be the reason for the amplifier not starting.
• Remove the speaker wires and reset the amplifier. If the protection LED still comes on then the amplifier is
faulty. This damage may have been caused by either failure to follow these setup guidelines or abuse.
AMPLIFIER GETS VERY HOT
• Check the minimum speaker impedance for the amplifier is correct. This amplifier is not recommended for
impedance loads below 2 Ohm stereo and / or 4 Ohm bridged mono.
• Check for shorts on all speakers wires. (i.e no speaker wires should be joined together and no speaker wires
should be touching the car’s chassis)
• Check that there is good airflow around the amplifier. In some applications an external fan may be required.
BLOWN FUSE(S)
• Check both positive supply and ground for shorts.
• Check that the positive wire is connected to the positive terminal on the amplifier.
• Check that the negative wire is connected to the ground terminal on the amplifier.
• Ensure that the correct rated fuse is fitted:
FLI UNDERGROUND 720.4 (25 amp x 2)
DISTORTED SOUND
• Check the gain control is not set at too high a level. If the speakers sound distorted turn the down the gain
until the sound is clear.
• Check that all crossover frequencies are correct. See Setup section for more details.
• Check for shorts on all speaker wires.
• Check all speakers are wired correctly. With the correct polarity being observed on each connection.

9
notes

10
specifications
KEEP IT SAFE
Staple your receipt here:
MODEL NUMBER:
SERIAL NUMBER:
PURCHASED FROM:
DATE OF PURCHASE:
In order to protect your purchase and aid your warranty please fill
in the following form and keep it safe for your future reference.
For more information and to register your warranty online, visit:
www.fliaudio.com/warranty
2
Model FU360.2 FU720.4 FU1000 .1 FU1000.5
Type 2/1 channel 4/3/2 channel monoblock 5/4/3 channel
Class AB AB D AB
4 ohm stereo 2 x 70 watts RMS 4 x 70 watts RMS N/A 4 x 70 watts RMS
2 ohm stereo 2 x 90 watts RMS 4 x 90 watts RMS N/A 4 x 90 watts RMS
4 ohm mono 1 x 180 watts RMS x 180 watts RMS 1 x 300 watts RMS 1 x 140 watts RMS
2 ohm mono N/A N/A 1 x 500 watts RMS N/A
Max power 360 watts 720 watts 1000 watts 1000 watts
Frequency response 20Hz – 20kHz 20Hz – 300Hz 10Hz - 5000Hz 20Hz - 20kHz
Height 1.9” (49mm) 1.9” (49mm) 1.9” (49mm) 1.9” (49mm)
Width 10.8” (254mm) 14” (334mm) 14” (355mm) 19.9” (505mm)
Depth 7.6” (197mm) 7.6” (197mm) 7.6” (197mm) 7.6” (197mm)

LIMITED WARRANTY
All FLI goods are covered by a full 12 months manufacturers warranty. Valid
from the date of the original receipt and proof of purchase. In order to validate
this warranty, the warranty card should be returned to FLI within seven days
of the original purchase date. The original receipt and packaging should also
be kept for this 12 month period.
If at any stage during the warranty period you have a problem with the product
then it should be returned to the point of purchase in its original packaging,
complete and with no items missing. If the store is unable to fix the product it
may have to be returned to FLI this process takes around 7 working days.
A full description of FLI’s warranty information can be found on our website:
www.fliaudio.co.uk/warranty
A written version can also be obtained from:
FLI warranty department
PO Box 11000
B75 7WG
COPYRIGHT
All content included in this manual such as text, graphics, logos, icons, images data, the selection
and arrangement thereof, are the property of FLI Audio (herein referred to as “FLI”, “us” or “we”)
and its affiliate or their content and technology providers, and are protected by United Kingdom
and International copyright laws. All rights reserved.
TRADEMARKS
FLI UNDERGROUND™, FU™, UNDERGROUND™ and all stylised representations of product
names, or the abbreviations of product names, as logos are all trademarks of FLI. Graphics and
logos are trademarks or trade dress of FLI Audio or its subsidiaries. FLI’s trademarks and trade
dress may not be used in connection with any product or service that is not FLI’s, in any manner
that is likely to cause confusion among customers or in any manner that disparages or discredits
FLI. All other trademarks not owned by FLI or its subsidiaries that appear in this manual are the
property of their respective owners, who may or may not be affiliated with, connected to, or
sponsored by FLI or its subsidiaries.
We reserve the right to make needed changes or improvements to the product
and this manual, without informing the customer about this in advance.
11

AVAILABLE NOW IN THE
FLI UNDERGROUND RANGE:
UNDERGROUND
www.fliaudio.com
up to
up to
270 watts
270 watts
speakers
FU 4 FU 5 FU 6 FU 69 FU 5c FU 6c
FU 10 FU 12 FU 15
FU 360 FU 720 FU 1000.1 FU 1000.5
FU 10P
FU 10A
FU 12P
FU 12A
FU 12TP
FU 12TA
up to
up to
1200 watts
1200 watts
up to
up to
1000 watts
1000 watts
up to
up to
2000 watts
2000 watts
subwoofers
AMPLIFIERS
ENCLOSURES

лтззлюбым
дбнымбм
глтчня
лжбдджи
Дтвззв
вии
фмлнидит
нлнз2минты
мнииДтвилтвинитзывыцииииди
FLI Underground FU720.4-F1
Описание