Flight Display Systems FD600CAM-2 User manual

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 1 of 12
FD600CAM-2/FD600CAM-2 Ver 28V
Installation and Operation Manual
Glareshield Camera
TECHNICAL SUPPORT
678-867-6717, or
www.FlightDisplay.com

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 2 of 12
FD600CAM-2/FD600CAM-2 Ver 28V
Glareshield Camera
© 2008 Flight Display Systems. All Rights Reserved.
Flight Display Systems
1765 Grassland Parkway
Alpharetta, GA 30004
678-867-6717 Phone
678-867-6742 Fax
[email protected]
www.flightdisplay.com
For the most current copy of all product manuals, please visit our website at
www.flightdisplay.com

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 3 of 12
Table of Contents
General Information......................................................................................................................4
1. Front View..........................................................................................................................4
2. Specifications .....................................................................................................................4
Installation Instructions .............................................................................................................5
1. Power ..................................................................................................................................5
Wiring Suggestions .....................................................................................................................6
1. Composite Wiring.............................................................................................................6
2. Power & Ground Wiring .................................................................................................6
3. Power/Video .....................................................................................................................7
Technical Drawing.......................................................................................................................8
Troubleshooting...........................................................................................................................9
1. Video Noise........................................................................................................................9
2. VGA Shadowing ...............................................................................................................9
3. Snow or Sweeping Lines..................................................................................................9
4. No Power to Monitor, or No Video Input.....................................................................9
5. Color Distortion.................................................................................................................9
6. Remote Control Inoperable .............................................................................................9
Technical Support......................................................................................................................10
Instructions for Continued Airworthiness ...........................................................................10
Warranty ......................................................................................................................................11
Log of Revisions.........................................................................................................................12

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 4 of 12
General Information
The FD600CAM-2 and the FD600CAM-2 Ver 28V are Glareshield Cameras. This small
color camera, when mounted in the cockpit, will provide passengers with an opportunity to
observe taxi, take-off, and landing, adding a whole new dimension to the In-Flight
Entertainment experience!
Front View
Specifications
Video System
NTSC or PAL
Video Output
1Vp-p, 75 Ohms
Camera Sensor
1/3” Color CCD
Camera Lens
4.0mm & 8.00mm (included)
Camera Shutter Speed
F 1.2
Picture Element
811H x 508V NTSC
(795H x 596V PAL)
Horizontal Resolution
480 Lines
Scanning System
2:1 Interlace
Signal to Noise Ratio
>48 dB
Minimum Illumination
.05 Lux
Dimensions, Camera
1.35” (W) x 1.35” (H) x 2.92” (D)
Dimensions, Mount
2.0” (W) x 1.75” (H) x 1.75” (D)
Weight
6 oz
Power
FD600CAM-2 - 12VDC @ 90 mA
FD600CAM-2 Ver 28V – 28VDC @ 45 mA
Operating Temperature
14°F to 140°F

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 5 of 12
Installation Instructions
All cabin entertainment equipment, such as the FD600CAM-2 and the FD600CAM-2 Ver
28V, should be installed on a non-essential bus and have a dedicated circuit breaker. It is
a requirement that a switch be installed in the cockpit so that the pilot can de-energize the
entertainment system should it become necessary.
Mounting from the cockpit headliner is suggested. Excessive sunlight will make the video
image hard to see. Mounting inside the cockpit and out of direct sunlight will provide a
“visor” to the camera lens.
Remember to set the camera pointing down at an approximately 60° angle, as this will
optimize the picture for takeoff and landings. When looking at the image while on the
ground have the horizon 2/3 of the way up the video screen in the cabin.
Power
The FD600CAM-2 is a 12VDC camera that requires 90mA power and can operate at 9 -
15VDC. The FD600CAM-2 Ver 28V is a 28VDC camera that requires 45mA power and
can operate at 15 - 29VDC.

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 6 of 12
Wiring Suggestions
All shields should be grounded to the connector at the source, and floating at the display.
Avoid routing video wiring parallel to:
•AC wiring
•Strobe wiring
•DC motor supply cables
•Inverter cabling
•Or any other potential noise source.
Composite Wiring
Recommended cable for s-video/composite and audio purposes is PIC 75 Ohm Coax, P/N
V76261. This is a lightweight, flexible, and low signal loss cable which meets FAA
flammability requirements of FAR 23.1359(d), FAR 25.853(a) and FAR 25.869(a)(4).
Similar aviation coaxial cable can be used from other vendors, as well. Some aircraft are
prone to AC noise - we recommend adding to the composite source a 75Ohm video
isolation transformer such as Deerfield Laboratory, Inc. Part No. 162-1
(www.deerfieldlab.com, [phone]). In most cases this should be added to the video
output of the source.
Power and Ground Wiring
22 AWG wire is recommended for Power and Ground applications.

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 7 of 12
Power/Video
Standard Density DB-9 Receptacle (supplied)
Connector P/N: M24308/2-281 or Equivalent
Crimp Contacts P/N: M39029/63-368 or Equivalent
Pin
Number
FD600CAM-2
Description
FD600CAM-2 Ver 28V
Description
1
12VDC Power
28VDC Power
2
12VDC Ground
28VDC Ground
3
N/C
N/C
4
Composite Video – Shield
Composite Video – Shield
5
Composite Video – Signal
Composite Video – Signal
6
N/C
N/C
7
N/C
N/C
8
N/C
N/C
9
N/C
N/C

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 8 of 12
Technical Drawing

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 9 of 12
Troubleshooting
Video Noise
Check for an incorrect ground in the installation wiring. See specific examples of video
noise below, or visit http://flightdisplay.com/Grounding.pdf
VGA Shadowing
Most of shadowing problems are due to shielding on the wire. Locate the point where all of
the shields are connected. Cut away the shields, one at a time, while viewing the display on
the screen to observe which shield is causing the noise. Cutting away one shield at a time
will allow you to focus and isolate the video noise issue.
•Twisted pair wiring is prone to video noise. ECS VGA Wire
(Detailed under “Video Wiring Suggestions”) is recommended.
Snow or Sweeping Lines
Lines that slowly sweep up and down are a result of AC noise. This AC noise can be
generated by a power cart on the aircraft. Take the power cart off of the aircraft. Be careful
of inverter wiring, which can also cause noise. Stand off the wires, if necessary.
If snow or sweeping lines persist, it is possible that the ground is at an incorrect point in the
aircraft. Try moving the ground to another location.
No power to Monitor, or No video Input
• Verify correct wiring. Check the base receptacle connectors for possibly damaged pins.
• Check that the video source is:
1. Powered on,
2. In Play mode, and
3. Displaying video.
Color Distortion
• Adjust brightness and contrast settings using the buttons on the monitor.
Remote Control Inoperable
• Confirm that the infrared eye on the LCD screen is visible.
• Replace battery in remote control.

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 10 of 12
Technical Support
Should you have any questions concerning this product or other Flight Display Systems
products, please contact our Product Support representatives at [phone].
Flight Display Systems
1765 Grassland Parkway
Alpharetta, GA 30004
Phone: [phone]
Fax: [phone]
Email: [email protected]
For further product information, technical data and sample wiring diagrams, please click on
the Dealers section of our web site at www.flightdisplay.com
Instructions for Continued Airworthiness
The FD600CAM-2 and the FD600CAM-2 Ver 28V is designed not to require regular
general maintenance.

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 11 of 12
Warranty Information
Flight Display Systems warrants the FD600CAM-2 and the FD600CAM-2 Ver 28V against
material or manufacturing defects for a two-year period. Effective 1/1/2009, all equipment
sold after 1/1/2009 will have a 2-year warranty. Warranty begins on date of installation.
*The warranty registration card must be returned upon installation in order to validate the
two-year warranty. Any warranty registration not returned during this time period will default
to the date of purchase as the warranty start date.
If product support is required, please call our Technical Support team at 678-867-6717 to
obtain assistance. If the return of the unit to the factory is required, an RMA number will be
issued at that time. Flight Display Systems will, upon receipt of the failed hardware,
remanufacture or replace the unit at our discretion.
Flight Display Systems will pay Ground Shipping charges for warranted items. Charges for
express shipment will be the responsibility of the sender.
This warranty is not transferable. Any implied warranties expire at the expiration date of this
warranty. We shall not be liable for incidental or consequential damages.
This warranty does not cover a defect or failure that has resulted from improper or
unreasonable installation, use or maintenance, as determined by Flight Display Systems.
This warranty is void if there is any attempt to disassemble or open this product without
factory authorization.
Any labor charges associated with the removal of product or related troubleshooting by a
firm other than Flight Display Systems or its designee will not be covered.

Document Number:
MAN – FD600CAM-2/FD600CAM-2
Ver 28V
Rev:
D
Revision Date:
03/16/2011
Page 12 of 12
Log of Revisions
Rev
Date
Page
Description
A
03/08/2007
Initial Release
B
09/05/08
1
Updated camera lens specs, added operating temperature to
spec list
C
04/14/2009
1,6
Updated specifications, warranty info
D
03/16/2011
Added FD600CAM-2 Ver 28V, new Composite Wiring info, new
Pinout info, new Technical Drawing