Flight Display Systems FD104SMT User manual

Rev:
C
Revision Date:
09/04/2012
Page 1 of 16
MAN –FD104SMT
FD104SMT
Installation and Operation Manual
10.4” LCD and Slide Mount
Manufactured by MILIC, LLC with marketing support from Flight Display Systems.
This product does not have FAA PMA approval.
TECHNICAL SUPPORT
[phone], or
www.FlightDisplay.com
All manuals and user guides at all-guides.com
all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 2 of 16
MAN –FD104SMT
FD104SMT
10.4" LCD and Slide Mount
© 2010 Flight Display Systems. All Rights Reserved.
Flight Display Systems
1765 Grassland Parkway
Alpharetta, GA 30004
[phone] Phone
[phone] Fax
[e-mail]
www.flightdisplay.com
For the most current copy of all product manuals, please visit our website at
www.flightdisplay.com
For more product support information, please visit the following link at
http://support.flightdisplay.com/
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 3 of 16
MAN –FD104SMT
Table of Contents
General Information......................................................................................................................4
1. Front View..........................................................................................................................4
2. Additional information ....................................................................................................4
Specifications................................................................................................................................5
Installation Instructions .............................................................................................................5
1. Power ..................................................................................................................................5
Wiring Suggestions .....................................................................................................................6
1. S-Video/Comp and Audio Wiring.................................................................................6
2. VGA Wiring.......................................................................................................................7
3. Power and Ground Wiring..............................................................................................8
Power/Video..................................................................................................................................9
1. Pinout DB-15......................................................................................................................9
Operation Instructions..............................................................................................................10
1. Buttons..............................................................................................................................10
2. Remote Control Buttons.................................................................................................11
Technical Drawing.....................................................................................................................12
Troubleshooting.........................................................................................................................13
Technical Support......................................................................................................................14
Instructions for Continued Airworthiness ...........................................................................14
Warranty ......................................................................................................................................15
Log of Revisions.........................................................................................................................16
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 4 of 16
MAN –FD104SMT
General Information
The FD104SMT is a 10.4" LCD and Slide Mount which has features that allow
installation in the smallest of mounting areas with the minimum of interface equipment.
Built with retrofit aircraft integration in mind, this display can switch between three
video input sources using an infrared remote.
Front View
Additional Information
The FD104SMT, an integral part of the FD104SMT, utilizes a state of the art digital
video decoding chipset for the analog video input. The three video sources in order of
picture quality are VGA (computer graphics like moving maps), S-Video and
Composite Video (DVD, camera or VCR).
The FD104SMT can also be connected to existing video switchers and just take a
composite video input from a selector interface box. In this case multiple input sources
can be selected and displayed on the monitor.
The FD104SMT is visible to passengers when deployed, and is offered in a Left or
Right configuration. The FD104SMT-Lis mounted on the Left side of the bulkhead, to
extend to the right into the aisle, while the FD104SMT-Ris installed on the Right side
of the bulkhead, extending to the left into the aisle.
When the monitor is stowed a latching mechanism automatically engages. To deploy
the monitor for viewing, depress the latch release button above the front handle and
slide out.
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 5 of 16
MAN –FD104SMT
Specifications
Display Type
10.4” TFT Color LCD
Display Color
262,144 Colors
Screen Resolution
1024x768 (1280x768 supported)
Brightness
700 cd/m²
Display Size
8.24”(W) x 6.2” (H)
Weight
10.0 lbs
Power
28VDC @ 1.0 Amp
Video Inputs Supported
Composite Video, S-Video
Video Types Supported
NTSC/PAL
Screen control
On-Screen Display Menu
Remote Control
IR, included
Materials
Aluminum
DO-160E testing
Section 21 Category B
Dimensions Stowed
13.10”(W) x 11.25” (H) x 2.5” (D)
Dimensions Deployed
24.7”(W) x 11.25” (H) x 2.5” (D)
Slide Mount Type
Retractable –Enclosed Dual Slide Rail
Mechanism
Installation Instructions
All cabin entertainment equipment, such as the FD104SMT, should be installed on a
non-essential bus and have a dedicated circuit breaker. It is a requirement that a
switch be installed in the cockpit so that the pilot can de-energize the entertainment
system should it become necessary.
The FD104SMT is integrated with a rugged slide mount bracket. Usually the
FD104SMT is mounted against a bulkhead behind a seat, exposed to the interior. The
FD104SMT is secured by four #10 machine screws. The monitor locks into place when
stowed and held in place by a gas spring when deployed.
There is one DB-15 male connector on the back of the unit. The FD104SMT comes
with a female DB-15 connector and crimp pins. The FD104SMT has already been
connected to the slide mount and tested prior to shipping.
Power
This is a 28VDC monitor that requires 1.0 amp of power to operate. The unit turns on
automatically upon power application.
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 6 of 16
MAN –FD104SMT
Wiring Suggestions
All shields should be grounded to the connector at the source, and floating at the
display.
Avoid routing video wiring parallel to:
AC wiring
Strobe wiring
DC motor supply cables
Inverter cabling
Or any other potential noise source
S-Video/Composite and Audio Wiring
Recommended cable for s-video/composite and audio purposes is PIC 75 Ohm Coax,
P/N V75268. This is a lightweight, flexible, and low signal loss cable which meets FAA
flammability requirements of FAR 23.1359(d), FAR 25.853(a) and FAR 25.869(a)(4).
Similar aviation coaxial cable can be used from other vendors, as well.
Some aircraft are prone to AC noise - we recommend adding to the composite source
a 75Ohm video isolation transformer such as Deerfield Laboratory, Inc. Part No. 162-1
(www.deerfieldlab.com, [phone]). In most cases this should be added to the
video output of the source.
All manuals and user guides at all-guides.com
all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 7 of 16
MAN –FD104SMT
VGA Wiring
Recommended cable for VGA purpose is ECS P/N 453005. This is a single shielded
cable containing 5 separate coaxial cables, color-coded to match the functions of the
wires.
We recommend coax cables be terminated using solder sleeve coaxial cable
terminators such as Raychem Part Number CWT-4174-W122-5/9.
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 8 of 16
MAN –FD104SMT
Power and Ground Wiring
This is a 28VDC monitor that requires 1 amp of power to operate. To operate properly
this monitor requires an input voltage of 18-29VDC.
The rated current of the equipment and associated voltage drop should be taken into
consideration when selecting wire gauge. The following example is based on an install
with a 28VDC power system and a total of 50 feet of wire between the circuit breaker,
monitor and ground.
Example: 22awg wire has 16.2 Ohms per 1000 feet, this equates to .81 Ohms for 50
feet. 1 Amp of current on .81 Ohms will drop .81 Volts.
Resistance of Wire Type M22759/16-**
(** = Gauge)
Gauge (AWG)
OHMS/1000’
24
26.20
22
16.20
20
9.88
16
4.81
12
2.02
10
1.26
8
.701
Also, use short heavy gauge wire and a clean tight connection for ground.
It is the installer's responsibility to understand the product's requirements to install the
product in compliance with industry standards and safety.
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 9 of 16
MAN –FD104SMT
Power/Video
Pin out for High Density DB-15 Receptacle
Part Numbers for DB-15 connectors, manufactured by Tyco or Amp.
High density, D-sub, 15 contact receptacle (female) P/N 748565-1
HD15F pins P/N M39029/57-354
Pin Number
Description
1
28VDC Power
2
28VDC Ground
3
Composite Video –Signal
4
Composite Video –Shield
5
S-Video Y –Signal
6
S-Video Y –Shield
7
S-Video C –Signal
8
S-Video C –Shield
9
Red Video (Pin 1 on Standard VGA)
10
Green Video (Pin 2 on Standard VGA)
11
Blue Video (Pin 3 on Standard VGA)
12
Red Ground (Pin 6 on Standard VGA)
13
Green Ground (Pin 7 on Standard VGA)
14
Horizontal Sync (Pin 13 on Standard VGA)
15
Vertical Sync (Pin 14 on Standard VGA)
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 10 of 16
MAN –FD104SMT
Operation Instructions
The FD104SMT is continuously on but can be de-energized by removing power from
the entertainment system. No pilot or aircrew action is necessary during flight or
ground operation. It is necessary to stow the display during take-off and landing.
The passengers will be able to change the video output on the FD104SMT using the
video source select button on the display, or remotely throughout the cabin with the
included IR remote. Point the IR remote at the top of the LCD to make changes.
When applying 28VDC power, the display will turn on and look for a valid input on the
last known source. If no input is found, the display will go to standby mode. Pressing
the Select button will select new video input.
Button
Located at the top of the FD104CV LCD are seven buttons.
Operations are as follows (From Right to Left):
BUTTON
DESCRIPTION
Power
Used to turn the unit on or off.
(LED)
Right
Used to move through the menu options.
Left
Used to move through the menu options.
Up
Used to increase the adjustment of a menu option.
Down
Used to decrease the adjustment of a menu option.
Select
Used to select the input signal source.
Menu
Used to change the configuration of the picture
settings (Backlight, Brightness, Contrast, Saturation,
Hue, etc.)
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 11 of 16
MAN –FD104SMT
Remote Control Buttons
All manuals and user guides at all-guides.com
all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 12 of 16
MAN –FD104SMT
Technical Drawing
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 13 of 16
MAN –FD104SMT
Troubleshooting
Video Noise
Check for an incorrect ground in the installation wiring. See specific examples of video
noise below, or visit http://flightdisplay.com/Grounding.pdf
VGA Shadowing
Most of shadowing problems are due to shielding on the wire. Locate the point where
all of the shields are connected. Cut away the shields, one at a time, while viewing the
display on the screen to observe which shield is causing the noise. Cutting away one
shield at a time will allow you to focus and isolate the video noise issue.
Twisted pair wiring is prone to video noise. ECS VGA Wire (Detailed under
“Video Wiring Suggestions”) is recommended.
Snow or Sweeping Lines
Lines that slowly sweep up and down are a result of AC noise. This AC noise can be
generated by a power cart on the aircraft. Take the power cart off of the aircraft. Be
careful of inverter wiring, which can also cause noise. Stand off the wires, if necessary.
If snow or sweeping lines persist, it is possible that the ground is at an incorrect point
in the aircraft. Try moving the ground to another location.
No Power to Monitor, or No Video Input
Verify correct wiring. Check the base receptacle connectors for possibly
damaged pins.
Check that the video source is:
1. Powered on,
2. In Play mode, and
3. Displaying video.
Color Distortion
Adjust brightness and contrast settings using the buttons on the monitor.
Remote Control Inoperable
Confirm that the infrared eye on the LCD screen is visible.
Replace battery in remote control.
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 14 of 16
MAN –FD104SMT
Technical Support
Should you have any questions concerning this product or other Flight Display
Systems products, please contact our Product Support representatives at (678) 867-
6717.
Flight Display Systems
1765 Grassland Parkway
Alpharetta, GA 30004
Phone: [phone]
Fax: [phone]
Email: [e-mail]
For further product information, technical data and sample wiring diagrams, please
click on the Dealers section of our web site at www.flightdisplay.com
Instructions for Continued Airworthiness
The FD104SMT is designed not to require regular general maintenance.
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 15 of 16
MAN –FD104SMT
Warranty Information
Flight Display Systems warrants the FD104SMT against material or manufacturing
defects for a two-year period. Warranty begins on date of installation. The warranty
registration card must be returned upon installation in order to validate the two-year
warranty. Any warranty registration not returned during this time period will default to
the date of purchase as the warranty start date.
If product support is required, please call our Technical Support team at +1 (678) 867-
6717 to obtain assistance. If the return of the unit to the factory is required, an RMA
number will be issued at that time. Flight Display Systems will, upon receipt of the
failed hardware, remanufacture or replace the unit at our discretion.
Flight Display Systems will pay Ground Shipping charges for warranted items. Charges
for express shipment will be the responsibility of the sender.
This warranty is not transferable. Any implied warranties expire at the expiration date of
this warranty. We shall not be liable for incidental or consequential damages.
This warranty does not cover a defect or failure that has resulted from improper or
unreasonable installation, use or maintenance, as determined by Flight Display
Systems. This warranty is void if there is any attempt to disassemble or open this
product without factory authorization.
Flight Display Systems shall not be held responsible for any labor charges associated
with the removal of product or related troubleshooting.
All manuals and user guides at all-guides.com

Rev:
C
Revision Date:
09/04/2012
Page 16 of 16
MAN –FD104SMT
Log of Revisions
Rev
Date
Page
Description
A
11/3/2008
---
Initial Release
B
04/10/2009
2,11
Updated specifications, warranty info
C
09/04/2012
Updated format, warranty and non-PMA info
All manuals and user guides at all-guides.com
all-guides.com