Insignia NS-13SGAM User manual

SAFETY INFORMATION AND SPECIFICATIONS....2
PACKAGE CONTENTS: PARTS.....................................3
PACKAGE CONTENTS: HARDWARE..........................5
ASSEMBLY INSTRUCTIONS.........................................6
CARE AND MAINTENANCE...................................... 24
47” Espresso
Gaming TV Stand
NS-13SGAM
Before using your new product, please read these instructions to prevent any damage.
USER GUIDE
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 1 Thursday, May 1, 2014 11:22 AM

2
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
SAFETY INFORMATION AND SPECIFICATIONS
CAUTION: The top surface of this stand
is designed for use with a product
weighing no more than
95 lbs. (43 kg) and having a width that
permits it to sit evenly on the stand
with no more than a one-inch overhang on each
side of the shelf. Use with products that weigh more
than the maximum weight allowed, or with
dimensions that extend beyond the maximum
width may result in instability, which may result in
injury.
CAUTION: This product contains small
items that could be a choking hazard if
swallowed.
Keep these items away from young
children!
Model #: NS-13SGAM
Maximum weight: 95 lbs. (43 kg)
Maximum width: 1-inch overhang on each
side of the top shelf
Overall dimensions (W × H × D):
47.3 × 26.5 × 19.5" (120 × 67.3 × 49.5 cm)
47.3" (120 cm) 19.5" (49.5 cm)
26.5" (67.3 cm)
95 lbs. (43 kg)
30 lbs. (13.6 kg)
25 lbs. (11.3 kg)
45 lbs. (18.1 kg)
Drawer will
hold 15 lbs.
(6.8 kg)
Drawer will
hold 15 lbs.
(6.8 kg)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 2 Thursday, May 1, 2014 11:22 AM

3
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
PACKAGE CONTENTS: PARTS
Tools needed:
Phillips screwdriver
Hammer
ARight end (1) BLeft end (1) CRight upright (1)
DLeft upright (1) FTop (1)
GBottom (1) HShelf (1)
EUpright (1)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 3 Thursday, May 1, 2014 11:22 AM

4
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
PACKAGE CONTENTS: PARTS (CONTINUED)
I Back (1) JAdjustable shelf (1)
KFront skirt (1) LSide skirt (2)
MDrawer front (2)
RLeft front/right
rear foot (2)
SRight front/left
rear foot (2)
TCenter
foot (2)
D73 Drawer
back (2)
D16 Right drawer
side (2)
D17 Left
drawer side (2)
D720 Drawer
bottom (2)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 4 Thursday, May 1, 2014 11:22 AM

5
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
PACKAGE CONTENTS: HARDWARE
Note: You may receive extra hardware. Make sure you have all the hardware necessary to
assemble your new TV stand:
Label Hardware Qty.
U2
V2
W2
X2
Y2 10
Z2 10
AA 1
BB 1
CC 4
DD 3
Right drawer rail
Left drawer rail
Right drawer slide
Left drawer slide
Hidden cam
Cam dowel
Corner cap
Foot bracket
Corner bracket
Metal bracket
Label Hardware Qty.
EE 2
FF 4
GG 4
HH 10
II 4
JJ 1
KK 10
LL 8
MM 2
NN 35
OO 16
PP 48
Knob
Side cam
Cam cover
Metal pin
Rubber sleeve
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur. The TV and furniture will be
unstable and may tip.
- The TV must weigh less than 95 lbs.
- The base of the TV must be able to sit
completely on this shelf.
Warning label
Black 1-15/16" flat head screw
Black 1-9/16" flat head screw
Gold 1" machine screw
Black 9/16" large head screw
Gold 5/16" flat head screw
Nail
10 20 30 40 50 60 70 80 90 100mm
1234in
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 5 Thursday, May 1, 2014 11:22 AM

6
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
ASSEMBLY INSTRUCTIONS
Step 1: Assemble the ends and uprights
Note: Assemble your TV stand on carpeted floor or on the empty carton to avoid scratching your stand or the floor.
1Push two hidden cams (Y2) into the right end (A), left end (B), and right upright (C) and four hidden cams in the
shelf (H). Make sure that the arrows on the hidden cams point to the holes on the edges of the right end, left
end, right upright, and shelf.
2Insert the metal end of a cam dowel (Z2) into the side of each hidden cam, then press in on the dowel until it
snaps into place.
Y2
Z2
Y2
Z2
Important: Do not tighten the hidden cams in this step.
Arrow
Arrow
You’ll need:
Y2 (10) Z2 (10)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 6 Thursday, May 1, 2014 11:22 AM

7
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 2: Attaching the drawer rails
• Fasten the two right drawer rails (U) to the right end (A) and the two left drawer rails (V) to the right upright (C)
using two gold 5/16" flat head screws (OO) per rail.
OO
OO
OO
OO
OO
OO
OO
OO
OO
OO
Rounded
edge Roller
ends
Finished
edge
Roller
ends
You’ll need:
V(2) OO (8)U(2) Phillips screwdriver
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 7 Thursday, May 1, 2014 11:22 AM

8
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Tip: How to tighten hidden cams
In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not
completely tightened will loosen, and parts may separate.
Arrow
Make sure that you turn the
hidden cam a minimum of
190° to a maximum of 210°.
Note the position of the arrow
on the hidden cam.
Arrow
In the illustration below,
the hidden cam has not
been tightened enough.
210°
190°
You’ll need:
Phillips screwdriver
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 8 Thursday, May 1, 2014 11:22 AM

9
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 3 : Attach the top to the left end
1Identify the rounded edge on the left end (B) and the top (F) and the finished edge on the upright (E). Make sure
these edges face the same direction.
2Place the top (F) face down, then insert the cam dowels on the left end (B) into the holes on the top (F). The side
of the left end (B) that has the hidden cams should face the center of the top (F). Use a Phillips screwdriver to
tighten the two hidden cams in the left end (B).
3Insert two metal pins (HH) in the upright (E), then insert the other ends of the metal pins into the holes in the
top (F).
HH
Surface with
holes
Rounded edge
Finished edge
Rounded
edge
Arrow
210°
Surfacewith
hiddencams
190°
You’ll need:
HH (2) Phillips screwdriver
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 9 Thursday, May 1, 2014 11:22 AM

10
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 4 : Attach the shelf
1Make sure that the side of the shelf (H) with the hidden cams faces up, and the finished edge faces the same
direction as the finished edge on the upright (E).
2Insert the cam dowels on the edge of the shelf (H) into holes on the left end (B), then use a Phillips screwdriver
to tighten the hidden cams in the shelf (H).
3Fasten the shelf (H) to the upright (E) using two black 1-15/16" flat head screws (KK).
KK
KK
210° Arrow
Finished edge
190°
You’ll need:
KK (2) Phillips screwdriver
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 10 Thursday, May 1, 2014 11:22 AM

11
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 5: Install the uprights
1Make sure that the finished edge on the right upright (C) and on the left upright (D) faces the same direction as
the finished edge on the shelf (H).
2Insert the two cam dowels on the right upright (C) into the holes on the shelf (H), then use a Phillips screwdriver
to tighten the hidden cams on the right upright (C).
3Insert two metal pins (HH) into the left upright (D), then insert the other ends of the metal pins into the holes in
the shelf (H).
HH
210° Arrow
SurfaceWITHOUT
holes
Surfacewith
rails
Finished edges
190°
You’ll need:
Phillips screwdriver
HH (2)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 11 Thursday, May 1, 2014 11:22 AM

12
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 6: Install the right end
1Make sure that the side of right end (A) that has the rails attached faces the center of your TV stand.
2Insert the cam dowels on the edge of the right end (A) into the holes on the top (F), and insert the cam dowels
on the edge of the shelf (H) into the holes on the right end (A).
3Use a Phillips screwdriver to tighten the four hidden cams: two in the right end (A) and two in the shelf (H).
Surfacewithrails
Rounded
edge
210° Arrow
190°
You’ll need:
Phillips screwdriver
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 12 Thursday, May 1, 2014 11:22 AM

13
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 7: Install the bottom
1Make sure that the rounded edge on the bottom (G) faces forward.
2Fasten the bottom (G) to the ends (Aand B) and uprights (Cand D) using eight black 1-15/16" flat head
screws (KK).
KK
KK
KK
KK
KK
KK
KK
KK
Rounded edge
You’ll need:
Phillips screwdriver
KK (8)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 13 Thursday, May 1, 2014 11:22 AM

14
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 8: Install the corner brackets
1Fasten four corner brackets (CC) to the feet (Rand S) using two black 9/16” large head screws (NN) per bracket.
2Make sure that the narrow edges of the feet (Rand S) face the same direction as the finished edges of the side
skirts (L).
3Fasten the feet (Rand S) to the side skirts (L) by inserting two black 9/16" large head screws (NN) through each
corner bracket (CC). Tighten the screws.
NN
CC
CC
CC
CC
NN
NN NN
NN
NN
NN
NN
NN
NN
CC
NN
NN
CC
NN
NN
CC
NN
NN
CC
Finished
edge
Finished
edge
You’ll need:
Phillips screwdriver
CC (4) NN (16)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 14 Thursday, May 1, 2014 11:22 AM

15
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 9: Install the skirts
1Insert a metal pin (HH) into each end of the front skirt (K).
2Align the front skirt (K) to the front edge of the bottom (G), then insert the ends of the metal pins into the feet (R
and S). Make sure that the finished edges face up and toward the front.
3Fasten the side skirts (L) to the bottom (G) by inserting two black 9/16" large head screws (NN) through each
corner bracket (CC). Tighten the screws.
HH
NN NN
CC
NN NN
NN NN
CC
CC
NN NN
CC
NN NN
CC
Holes should be here
Finishededge
Unfinished
edge
You’ll need:
Phillips screwdriver
HH (2) NN (8)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 15 Thursday, May 1, 2014 11:22 AM

16
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 10: Install the skirt brackets and the foot
1Fasten three metal brackets (DD) to the bottom (G) and front skirt (K) using two black 9/16" large head
screws (NN) per bracket.
2Fasten the foot bracket (BB) to the bottom (G) using three black 9/16" large head screws (NN).
3Slide the two center feet (T) onto the foot bracket (BB).
4Use two black 9/16" large head screws (NN) to fasten the foot bracket (BB) to the center feet (T).
Note: There are no pre-drilled holes in the center feet (T). The screws tighten into the grooves.
5Insert the corner cap (AA) into the grooves in the center feet (T).
DD
DD
DD
BB
AA NN
NN
NN
NN
NN
NN
DD
NN
NN
NN
NN
NN
NN
You’ll need:
Phillips screwdriver
AA (1) BB (1) DD (3) NN (11)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 16 Thursday, May 1, 2014 11:22 AM

17
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 11: Install the back
1Carefully turn your TV stand over onto its front edges. Unfold the back (I) and lay it over your TV stand.
2Make equal margins along all four edges of the back (I). Push on opposite corners of your TV stand if needed to
make it “square.”
3Fasten the back (I) to your TV stand using the 48 nails (PP).
Note: Make sure that you tap nails into the holes that line up over the uprights and shelf.
Note: Perforations have been provided for access through the back. Carefully cut out the holes needed.
PP
Do not stand your TV stand upright
without the back attached. Your stand
might collapse.
These holes must line up
over the uprights and shelf.
You’ll need:
PP (48) Hammer
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 17 Thursday, May 1, 2014 11:22 AM

18
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 12: Assemble the drawer
1Insert the tab on the right drawer side (D16) at an angle into the slot on the right side of a drawer front (M). The
tab should easily fit into the slot. Gently tilt the drawer side (D16) from side to side until the tab slips into the
slot. Repeat to fasten the left drawer side (D17) to the left side of the drawer front (M).
2Slide a drawer bottom (D720) into the grooves in the drawer sides (D16 and D17) and drawer front (M).
3Repeat this step to make the other drawer.
*U.S. Patent No. 6,413,007
D16
D17
D720
D16
D16
D17
Tab
Slot
Groove
Unfinished surface
The tabs should insert freely
into the slots. Gently tilt the
drawer sides from side to
side until the tabs slip into
the slots.
Be sure the drawer
bottom inserts
into the drawer
front groove.
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 18 Thursday, May 1, 2014 11:22 AM

19
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 13: Assemble the drawer (continued)
1Fasten a drawer back (D73) to the drawer sides (D16 and D17) using four black 1-9/16" flat head screws (LL).
Note: Make sure that the drawer bottom (D720) inserts into the groove in the drawer back (D73).
2Repeat this step for the other drawer.
LL
LL
LL
LL
D16
D17
D720
D73
You’ll need:
LL (8) Phillips screwdriver
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 19 Thursday, May 1, 2014 11:22 AM

20
47” ESPRESSO GAMING TV STAND
www.insigniaproducts.com
Step 14: Attach the drawer slides
1Insert a slide cam (FF) into the drawer sides (D16 and D17).
2Fasten the drawer slides (Wand X) to the drawer sides (D16 and D17) using two gold 5/16" flat head
screws (OO) per slide.
Note: The drawer slides are marked “DRAWER RIGHT” and “DRAWER LEFT” for easy identification.
Note: The screw head in the cam must be visible through the slotted hole in the slide.
3Repeat this step for the other drawer.
FF
FF
OO
OO
OO
OO
D16
D17
Roller end
Turn the cam to line up
the screw head with
the hole in slide.
Roller end
Turn the cam to line up
the screw head with
the hole in slide.
You’ll need:
Phillips screwdriver
W(2) X(2) FF (4) OO (8)
NT-13SGAM_14-0248_MAN_V1_ENG.fm Page 20 Thursday, May 1, 2014 11:22 AM