Fly Dragon Light Sky PCL19-420 User manual

USER MANUAL
PROFESSIONAL SHOW LIGHTING
LED
PCL19-420
www.lightsky.com.cn/www.lightsky-china.com
FLY DRAGON LIGHTING EQUIPMENT CO., LTD
AC100~240V
50~60H

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
1
CONTENTS
1. General information 2
2. Safety instructions 3
3. Performance trait an skill specifications 4
4. Operation panel 6
5. Dimensional rawings 6
6. Photometric ata 7
7. Mounting an Installation 8
8. Power supply an Signal connection 9
9. Display menu 11
10. DMX traits 17
11. Circuit connecting iagram 21
12. Explo e iagram an List 22
13. Trouble ispose 24
14. Cleaning an Maintenance 25
15. Duty exonerative an Copyright protection 25

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
2
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, ou have just purchased one of the
most innovative and reliable LED fixtures on the market toda . Our
compan has been designed to perform reliabl for ears when the
guidelines in this booklet are followed. Please read and understand the
instructions in this manual carefull and thoroughl before attempting to
operate this unit. These instructions contain important information
regarding safet during use and maintenance.
UNPACKING: Thank ou for purchasing our compan products. Ever
product has been thoroughl tested and has been shipped in perfect
operating condition. Carefull check the shipping carton for damage that
ma have occurred during shipping. If the carton appears to be damaged,
carefull inspect our fixture for damage and be sure all accessories
necessar to operate the fixture have arrived intact. In the event damage
has been found or parts are missing, please contact our customer support
team for further instructions. Inside the box ou should find: the fixture,
a DMX XLR cable, a power cable, and this user manual.
Please do not discard the shipping carton in the trash. Please rec cle
whenever possible.
Notice: As part of our ongoing commitment to continuous
products update, compan will keep the right to improve
this products, the information in this menu ma be
changed in the future, the compan reserve the right to
change the data without an advises.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
3
2. SAFETY INSTRUCTIONS
●1. In order to ensure the light could operate normall , the ambient
temperature couldn't be higher than 35℃ and no lower than- 2℃.
●2. Under normal condition, the highest sectional surface temperature
ma be up to 60 ℃.
●3.These projectors are designed depends on the electric shock
protection, the projector should be connected with the power suppl
s stem which connected ground enough. The projector's ground
cable should be connected with the ground cable of the power
suppl s stem as well. The ground mark of the light metal cover
should be connecting with the installation bricked steadil .
●4.Connecting the main power suppl should be done b the
professional person.
●5.Please check the voltage, frequenc data of power suppl s stem is
suitable for the mentioned on the projector. Please do avoid the
different voltage between them and burn the projector.
●6.Do not attempt to operate this fixture if the power cord has become
damaged or fra ed.
●7.Never open this fixture while in use.
●8.Never look directl into the light source. You risk injur to our
retina, which ma induce blindness.
●9.Please be aware that damages caused b modifications to the device
are not subject to warrant .
Notice: To guarantee proper and consistent operation, it is
important to follow the guidelines in this manual. Our
compan will not accept responsibilit for damages
resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
4
3. PERFORMANCE TRAIT AND SKILL SPECIFICATIONS
◎Lighting equipment use the LED illuminant with high performance
and super luminance.
◎High performance and energ saving permanent current LED driving
circuit and software control s stem, with perfect dimmer color s stem
and splendid performing function..
◎Appearance material:. Die casting aluminum radiator.
◎ operation panel use the LED displa screens.
◎ Cooling performance: It adopt the new-st le and absolute double space cooling.
B separating the two heating capsule, it forms the double construction of the
air intake space and heat diffusion space. which will be know as a good cooling
performance and absolutel extend the service lifetime.
◎ High precision temperature monitor function: monitoring the phosphor board
and PCB board simultaneousl .
◎ Standard DMX-512.
◎ DMX channel support three channels mode.
◎ Default scene after power: the fixture can automaticall adjust the default scene
after power according to the inner setting.
◎ Automatic run function: Support 4 automatic run procedures, support the Menu
and controller scene edit function. The most can be 100 scene.
◎ Automatic distinguish function: It support DMX control signal priorit .
Regardless of an state, the fixture will automaticall switch to the DMX
controlled state once receiving DMX signal, if no DMX signal, the fixture can
automaticall switch to the DMX signal control, black scene, the default scene
and automatic run procedures state according to its inner setting.
◎ Address code function: Each fixture can set IP address separatel , the most can
be setting 64 IP.(0 is a common IP and is available for all the IP.). that means
the biggest IP range is 512*64.
◎ Color mixing: Unlimited color mixing s stem
◎ Dimmer: Continuous dimming 0~100%.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
5
◎ Shutter: Electronic shutter 0~18Hz.
◎ LED life: 50,000 hours rated life.
◎ Single carton size: 335x335x472(mm)
◎ N.W.: 8.9kg G.W.: 10.3kg
◎ LED：19PCS 4 in 1
◎ Lens angle:20 °
◎ Power ： 195W

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
6
4. OPERATION PANEL
5. DIMENSIONAL DRAWINGS

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
7
6. PHOTOMETRIC DATA
20°lens

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
8
7. MOUNTING AND INSTALLATION
Cautions:
For added protection mount the fixtures in areas outside walking
paths, seating areas, and awa from areas were unauthorized personnel
might reach the fixture. Before mounting the fixture to an surface, make
sure that the installation area can hold a minimum point load of 10 times
the device's weight. Fixture installation must alwa s be secured with a
secondar safet attachment, such as an appropriate safet cable. To
avoid injur , never stand directl below the device when mounting,
removing, or servicing the fixture.
Mounting points:
Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the
installation material being used, and periodic safet inspection of all
installation material and the fixture. If ou lack these qualifications, do
not attempt the installation ourself. Improper installation can result in
bodil injur . Be sure to complete all rigging and installation procedures
before connecting the main power cord to the appropriate wall outlet.
Mounting
Our compan is full operational in an mounting position, hanging
upside-down, side mounted, or set on a flat level surface, etc. Be sure this
fixture is kept at least 0.5m (about 1.6feet) awa from an flammable
materials (decoration etc.).
When clamp mounting; alwa s use and install the supplied safet
cable as an added safet measure to prevent accidental damage in the
event of a clamp failure. See the image below.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
9
8. POWER SUPPLY AND SIGNAL CONNECTION
1. Power supply
Use the professional plug to connect the projector and main power
suppl . Please pa attention to the voltage, frequenc the same as the
mentioned on the projector. Suggest each light has separatel switched of
the power suppl so that could turn on or turn off each projector
desultoril .
2. Signal connection
Please use the round 3-pin XLR plugs &sockets offered b menu
facture to connect the first projector's output to the second projector'
input and connect the second projector's output to the third device's
input. And in the same wa for the rest, eventuall connect the last
device's output, all the devices are together as the following figure.
The devices’ control signal output or input b using the 3-pin XLR pug
and socket. If need to long then the communication cable, please make
sure the both side of 3-pin plug is one to one. (one to one, two to two,
three to three). Otherwise, the communication cable will be interrupted.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
10
The communicate cable is 2-pin shielded cable 75Ω
Resistance with each core is at least a 0.5mm diameter. (Caution: All the
inside leading wire of 3-pin XLR plug couldn't touch each other or
plinth).
Recommend to use the DMX signal terminator for the installation to
avoid the electronic noise damage the digital control signal. Simpl
speaking, DMX terminator is an XLR connector with a 120Ω 1/2w
resistor connected across pin 2 and 3.Which is then plugged into the
output socket on the last projector in the chain. Refer to the connection as
above:(Picture ).We suggest using the DMX signal distributor when the
distance of the lights over 15meter,In case of effect the light
communication because of the signal feeble.
3. Light power connection:
After doing the above operation and making sure all the devices had
been installed with natural operate, press the power switch to check
whether ever thing is working normall .

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
11
9. DISPLAY MENU
Power, press the ENTER button to enter the menu settings:
ESC：Exit Button； UP：Page up or increase；
DOWN：Page down or reduce； ENTER：OK button
Main
Menu
Ⅰ
Menu
Ⅱ
Menu
Ⅲ
Menu
Ⅴ
Menu Function
ADDR →
A.001
↓
A.512
Adjusting DMX addressing data
HOLD
DMX signal is off after the last state to
maintain controller
BLK DMX signal is off ,LED turn off all light
D.SCN
DMX signal is off, transferred to the
default scene
SCN.1
DMX signal is off, transferred to
user-defined scene 1
SCN.2
DMX signal is off, transferred to
user-defined scene 2
SCN.3
DMX signal is off, transferred to
user-defined scene 3
DMX.F →
SCN.4
DMX signal is off, transferred to
user-defined scene 4
13CH 13-channel mode
09CH 9-channel mode
DMX.S →
MODE →
08CH 8-channel mode

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
12
Main
Menu
Ⅰ
Menu
Ⅱ
Menu
Ⅲ
Menu
Ⅴ
Menu Function
R.000 The red channel values
G.000 The green channel values
B.000 The blue channel values
W.000 The white channel values
F.000 Soft speed channel values
C.000
Channel value of the macro
function
D.000 Dimmer channel values
S.000 shutter channel values
一
.000 The second shutter
： slake hold
time channel values
/.000 The second shutter: off to light
b the time channel values
一
.000 The second shutter: Brightness
hold time channel values
\.000 The second shutter: light to off
b the time channel values
LIST →
I.000 Select channel sub-code
Press
ENTER
button
to
editing
status
DMX.S →
EDT.S
→
ST.00
↓
ST.99
Save the current channel data to the scene
T.HRS → 0000 Device power on total
time(unit: hours)
P.TIM
→
R.HRS → 0000 Reset after power on
time(unit: hours)
T.TMS → 0000 The total number of device
power on
INFO →
P.TMS
→
R.TMS → 0000 Reset after power on number

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
13
Main
Menu
Ⅰ
Menu
Ⅱ
Menu
Ⅲ
Menu
Ⅴ
Menu
Function
T.HRS → 0000 LED light radiation board
the total time
L.TIM →
R.HRS → 0000 Reset after LED light
time(unit: hours)
CUR.T → 000C The temperature of the
current driver board
MAX.T → 000C Driver board temperature
record
TEM1 →
MAX.R → 000C Reset the maximum
temperature
CUR.T → 000C The temperature of the
current radiation board
MAX.T → 000C Radiation board
temperature record
TEM2 →
MAX.R → 000C Reset the maximum
temperature
INFO →
VERS → MCU.V → V*.**
MCU software version
number
OPEN Displa board Often bright
OPN.D
Full-screen flicker when DMX is off , often bright when
has DMX
CLOS
Displa board often off
SHU.D
Full-screen flicker when DMX is off , often off when has
DMX
DISP →
CLS.D often bright(.) when DMX is off ,flicker(.) when has DMX

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
14
Main
Menu
Ⅰ
Menu
Ⅱ
Menu
Ⅲ
Menu
Ⅴ
Menu
Function
L.DEF → 0000 Password “1111” Scene data
reset
→ D.SCN → ST.00
Select the default the
scene after the DMX
signal is off
STA.S → ST.00
Start
program
step
END.S → ST.00
End of the
program
step
→ SCN.1 →
SPED → 000P
Program
speed (time
= parameter
value
*0.1S)
STA.S → ST.00
Start
program
step
END.S → ST.00
End of the
program
step
AUTO
→
EDIT
→ SCN.2 →
SPED → 000P
Program
speed (time
= parameter
value
*0.1S)

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
15
Main
Menu
Ⅰ
Menu
Ⅱ
Menu
Ⅲ
Menu
Ⅴ
Menu
Function
STA.S → ST.00
Start program
step
END.S → ST.00
End of the
program step
→ SCN.3
→
SPED → 000P
Program
speed (time =
parameter
value
*0.1S)
STA.S → ST.00
Start program
step
END.S → ST.00
End of the
program step
EDIT
→ SCN.4
→
SPED → 000P
Program
speed (time =
parameter
value
*0.1S)
AUTO →
SL.ID →
ID.00
↓
ID.64
Address code set ID

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
16
Main
Menu
Ⅰ
Menu
Ⅱ
Menu
Ⅲ
Menu
Ⅴ
Menu
Function
FADE → F.100 Soft parameters from fast to slow set
(default is 100)
AUTO Automatic fan speed control operation
FANS →
MAX Maximum wind speed fan operation
SEND → S000 Send cr stal calibration
signal
PERS →
OSC.C →
CALI → C000 reception cr stal
calibration signal
REST → ENT Driver reset (equivalent to re-power)
LOAD → 0000 Password “1111”
Restore the factor
parameters, while device
reset
Status menu:
NO. Status Information Explain
1 A001-A512 DMX addressing data
2 SLAV Sub-light status
3 ST.00-ST.99 State of the main light
self-propelled
Information menu:
NO. Information Explain
1 NO.ER No error
2 ERR.T Temperature error
3 ERR.D DMX signal line error
4 ERR.M Memor data error

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
17
10、DMX TRAITS
function DMX values
and effect Remarks
RED 0-255 From dark to light dimming, color macro
function in adjustment phase
GREEN 0-255 From dark to light dimming, color macro
function in adjustment phase
BLUE 0-255 From dark to light dimming, color macro
function in adjustment phase
WHITE 0-255 From dark to light dimming, color macro
function in adjustment phase
FADE 0-255 Adjust the speed from fast to slow soft
0-3 No macro function
4-67
Fixed the macro function, alternating from
slow to fast RGB, white can be individuall
controlled
68-131 Fixed the macro function, alternating from
slow to fast RGBW
COLOR
132-255 Phase macro functions, from slow to fast, and
with the use of 1,2,3, and 4-channel

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
18
function DMX values
and effect Remarks
DIMMER 0-255 From dark to light dimming
0-1 Open light
2-64 Slow to off quick open (from slow to fast)
65-127 Slow to open quick off (from slow to fast)
128-190 Random shutter(from slow to fast)
191-253 from slow to fast
SHUTTER
254-255 Open light
CLOSE 0-255 The second shutter
：
slake hold time 0-3s
C_TO_O 0-255 The second shutter: off to light time 0-3s
OPEN 0-255 The second shutter: Brightness hold time 0-3s
O_TO_C 0-255 The second shutter: light to off 0-3s
0-2 All IDs are efficient lighting its own ID to 0,
the channel set to an value is valid
3-5 ID:1 effective
6-8 ID:2 effective
… …
192-194 ID:64 effective
195-197 ID is(2*n)+1 effective,(n=0-31)
198-200 ID is(2*n)+2 effective,(n=0-31)
201-203 ID is(3*n)+1 effective,(n=0-21)
204-206 ID is(3*n)+2 effective, (n=0-20)
207-209 ID is(3*n)+3 effective, (n=0-20)
210-212 ID is(4*n)+1 effective, (n=0-15)
213-215 ID is(4*n)+2 effective ,(n=0-15)
216-218 ID is(4*n)+3 effective, (n=0-15)
219-221 ID is(4*n)+4 effective,(n=0-15)
SLAVE
222-224 ID is(5*n)+1 effective,(n=0-12)

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsk .com.cn
www.lightsk -china.com
19
function DMX values
and effect Remarks
225-227 ID is(5*n)+2 effective,(n=0-12)
228-230 ID is(5*n)+3 effective, (n=0-12)
231-233 ID is(5*n)+4 effective, (n=0-12)
234-236 ID is(5*n)+5 effective,(n=0-11)
237-239 ID is(6*n)+1 effective,(n=0-10)
240-242 ID is(6*n)+2 effective,(n=0-10)
243-245 ID is(6*n)+3 effective,(n=0-10)
246-248 ID is(6*n)+4 effective,(n=0-10)
249-251 ID is(6*n)+5 effective,(n=0-9)
252-254 ID is(6*n)+6 effective,(n=0-9)
SLAVE
255 All IDs are valid