Fogco EC20 User manual

7 ft minimum
from oor to bottom of fan
required by OSHA
5 ft minimum
from fan to wall
for optimum airow
1Location
Locate optimum fan placement:
- Must be at least 7 ft from floor to
bottom of fan
- Place fan at least 5 ft from any wall for
optimum airflow
- Recommended placement 10-15 ft from
end wall and then every 30-40 ft
41’ 40’
40’ 41’
15’
15’
EC20
MAX
EC20
MAX
EC20
MAX
EC20
MAX
Example 30’ x 96
Greenhouse Layout
EC20 MAX SNAP-FAN INSTALLATION
!
Only a qualified and licensed electrician or contractor should install or service Snap-Fan products.
If someone other than a licensed electrician installs a Snap-Fan, Snap-Fan disclaims all warranties
for the product, and specifically disclaims any warranty for consequential damages.
EC20 MAX SNAP-FAN
Safety Information
Occupational Safety and Health Administration (OSHA) requires bottom of fan blade must be
at least 7 ft from floor.
Refer to installation and operation manuals before installing, servicing or operating this unit.
All applicable electrical safety precautions and building codes must be adhered to and followed
when installing this product.
!
!
!
Additional mounting
hardware supplied by
user may be needed.
MOTOR MOUNT
(TWO) 1 inch Steel Serrated Flange Head Bolt
and Serrated Flange Head Nut
RIGID CEILING MOUNT
For claims, please contact your retailer directly
or email us at: [email protected]
Visit snap-fan.com for replacement parts
Product Support & Contact Information
Snap-Fans are high efficiency ventilation fans designed to be used in ventilation
applications. Using this equipment for any other purpose or in a manner not
consistent with the operating recommendations within this manual will void the
warranty and may cause personal injury.
Fogco
600 S 56th St, Ste 9
Chandler, AZ 85226
480-507-6478
RETAIL RETURN POLICY Only applicable if you ordered directly from Fogco.
The goal of Fogco is that its customers be completely satisfied with their purchase. If you are not completely satisfied, you have 30 days
from the date of purchase to return the unused, undamaged product. Please first contact Fogco to obtain authorization for the return and
RGA # and then return the product to Fogco. All returns are subject to a 25% restocking fee. Upon receipt, the purchase price, less any
restocking fee, will be refunded so long as the product and its packaging is in merchantable condition. No returns will be accepted for
products that are not in a merchantable condition. No returns will be accepted without prior authorization and all shipping costs
are the sole responsibility of the purchaser. No returns will be accepted for products purchased from somewhere other than directly from
Fogco – any such returns should be made to that location and made in conformance with that location’s own return policy, (if any). Finally,
no returns will be accepted for custom made or special order items. If you have any questions about this policy, please contact us.
LIMITED WARRANTY
WARRANTY AND DISCLAIMER: Fogco extends this limited warranty to the original purchaser (the “Purchaser”) and warrants that fans
supplied by Fogco shall be free from original defects in workmanship and materials for five years from date of shipment, and warrants
that electronics and fan accessories be free from original defects in workmanship and materials for one year from date of shipment
provided those products have been properly handled, stored, installed, serviced, maintained and operated. This warranty shall not apply to
products which have been improperly installed, altered or repaired without Fogco’s express authorization, or altered or repaired in any
way so as, in Fogco’s judgment, to affect its performance or reliability or subjected to misuse, negligence, or accident, or incorrectly used in
combination with other products. Improper installation specifically includes, but is not limited to: (1) the use of the Product in an
environment where it is exposed to nominal voltage in excess of 24 volts DC, or in the case of an AC Product, in excess of the voltage
specified on the Product
(“overvoltage”); (2) use or storage in a setting where the product is exposed to inclement weather. Any damage that Fogco determines, in
its sole discretion, as resulting from misuse shall not be covered by any warranty.
LIMITATION OF REMEDY AND DAMAGES: All claims under this warranty must be first made by telephone to Fogco at 480-507-5478, within
15 days after discovery of the defect and prior to the expiration of five years from the date of shipment by the Company of the product
claimed defective, and Purchaser shall be barred from any remedy if Purchaser fails to make such claim within such period.
Within 30 days after receipt of a timely claim, Fogco will authorize the Purchaser to return the product to Fogco at Purchaser's sole expense
for inspection by Fogco. Following such inspection, Fogco will replace, or at its option repair, free of charge, any product it determines to be
defective, and it shall ship the repaired or replacement product to Purchaser F.O.B. point of shipment; provided, however, if circumstances
are such that as in Fogco’s sole judgment repair or replacement is impractical or that the repair or replacement would result in further
warranty work due to the particular use of the Product, the Purchaser's sole and exclusive remedy shall be a refund to the Purchaser of any
part of the invoice price paid to Fogco for the defective Product or part.
Under no circumstances shall Fogco be responsible for the cost of removal of the defective Product or part, damages due to removal, or any
expenses incurred in shipping the Product or part to or from Fogco, or the installation of the repaired or replaced Product or part. The
warranties set forth above do not apply to any components, accessories, parts or attachments manufactured by other manufacturers; such
being subject to that manufacturer’s warranty, if any. To the extent not prohibited by that manufacturer’s warranty, Fogco shall pass
through to Purchaser such manufacturer’s warranty.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, WHICH ARE HEREBY EXPRESSLY DISCLAIMED AND WAIVED. THIS WARRANTY CONSTITUTES SNAP-FAN’S SOLE
AND EXCLUSIVE WARRANTY FOR DEFECTIVE GOODS AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DEFECTIVE
PRODUCTS.
No employee, agent, dealer, or other person is authorized to give any warranties on behalf of Fogco or to assume for Fogco any other
liability in connection with any of its products except in writing and signed by an officer of Fogco.
TECHNICAL ADVICE AND RECOMMENDATIONS, DISCLAIMER: Notwithstanding any past practice or dealings or any custom of the trade,
sales shall not include the furnishing of technical advice or assistance or system design. Any such assistance shall be at Fogco’s sole option
and may be subject to additional charge.
Fogco assumes no obligation or liability on account of any recommendations, opinions or advice as to the choice, installation or use of
products. Any such recommendations, opinions or advice are given and shall be accepted at Purchaser's sole risk and shall not constitute
any warranty or guarantee of such Products, their performance, or their suitability for any particular purpose.
LIMITATION OF LIABILITY: The cumulative liability of Fogco to the Purchaser and any other persons for all claims in any way relating to or
arising out of the Products, including, but not limited to, any cause of action sounding in contract, tort, or strict liability, shall not exceed the
total amount of the purchase price paid for those Products which are the subject of any such claim. This limitation of liability is intended to
apply without regard to whether other provisions of this agreement have been breached or have proven ineffective even if Fogco has been
advised of the possibility of such claims or demands. In no event shall Fogco be liable to the Purchaser or any other person for any loss of
profits or any incidental, special, exemplary, or consequential damages for any claims or demands brought by the Purchaser or such other
persons.
INDEMNITY: Fogco's maximum liability to Purchaser and to any other user is as set forth above. Fogco makes no warranty to anyone for
any products not manufactured by it and shall have no liability for any use or installation of any Products (whether manufactured by Fogco
or other manufacturers) not specifically authorized by this sale. Purchaser acknowledges various warnings by Fogco regarding the products
and its installation and use and acknowledges that the Product should only be installed by a competently trained and licensed electrician or
contractor. If Fogco incurs any claims, lawsuits, settlements, or expenses (including attorney fees) for any loss, injury, death or property
damage including, but not limited to, claims arising out of the Purchaser’s or any end user’s installation or use of the products, the
Purchaser
shall indemnify and hold Fogco harmless unless such injury, death, or property damage unless such was the result of Fogco's sole
negligence or willful misconduct..

POWER : Neutral (L2)
POWER : Ground
VARIABLE SPEED : 0-10 +
VARIABLE SPEED : 0-10 -
SINGLE SPEED - 5V Out
SINGLE SPEED - 5V In
FACTORY ONLY - Programming
FACTORY ONLY - Programming
INPUT POWER
CONTROL INPUT
POWER : L1
A. verify anchor points are strong enough for added
weight of fan and mount
C. Secure mount directly to ceiling using
FOUR screws
B. Confirm flag of mount is in line with fan direction
and use level to ensure it is vertical 90 degrees
C
B
2Mount to Ceiling
B
D
C
E. Adjust Fan to desired angle
F. Tighten hardware to secure
Fan in place
Mount Fan
B. Insert flag of Ceiling Mount between flags
of Motor Mount. Line up center holes in
Ceiling Mount Arm to Motor Mount.
A. Using a 3/8” and 7/16” sockets or wrenches,
first loosen the 1/4” bolts attaching Motor
Mount to Motor to open gap for flag of
Ceiling Mount.
C. Using 1/2” sockets or wrenches secure with
one 5/16”-18 1 inch serrated flange head bolt
and nut. Do not tighten completely.
3
MULTI ZONE SPEED CONTROLLER AVAILABLE
AC 0-10v Fans
Variable Speed - Create the ideal
environment while saving energy
2 Zones - Divide growing environment
into multiple zones
Up to 20 FANS in each zone
Occupational Safety and Health Administration (OSHA) requires bottom of fan blade must be
at least 7 ft from floor.
WIRING INSTRUCTIONS
Positive
Enable
Negative
Speed 2 - 1600 RPM
Speed 3 - 1800 RPM
INPUT POWER
Ground
1. Connect fan’s Ground (green) and
Negative (black) wires to corresponding
wires from power source.
2. Connect Positive (white) wire to
positive wire from power source.
3. Enable wire (yellow) must be connected
to positive wire from power source for
fan to run. When it is connected to the
positive the fan will run on low speed
(1000 RPM). Enable wire is a low current
enable/disable switch the can be used for
on/off switching or thermostats.
SOLAR/BATTERY EC20 MAX DC
*NOT TO SCALE
!WARNING: NO SERIES WIRING.Do NOT wire multiple fans in series to power
supply. Only wire fans in parallel or directly to power supply. Wiring fans in
series will void warranty and may result in motor failure.
*NOT TO SCALE
1. Connect fan’s power leads to power
source of appropriate voltage.
The EC20 Max fan remains wired
to power. The fan will only draw
power and run when one of the
following modes is selected.
2. To run fan at factory programmed
max speed connect 5V Out (Orange
Wire) to 5V In (Yellow Wire).
To Run fan at factory programmed
half speed connect 5V Out (Orange
Wire) to 10V In (Red Wire).
3. To run fan using variable speed
control: Connect only the red (+)
and white (-) signal wires to 0-10V
control signal.
115 VOLT & 230 VOLT EC20 MAX AC
4. To run the fan on speed 2 (1600 RPM) couple (blue) wire with Positive (white) and
Enable (yellow) to the positive from power source. Enable wire will work the same as
previously described.
5. To run the fan on speed 3 (1800 RPM) couple the (red) wire with Positive (white) and
Enable (yellow) to the positive from power source. Enable wire will work the same as
previously described.
6. Use a wire nut or electrical tape to seal off any unused wires.
Please note - RPM’s listed are the MAX RPM the fan can run. Fan speed will fluctuate in
proportion to the amount of power it is receiving. If fan is wired directly to solar panel,
fan speed will vary depending on the amount of power the panel is producing
(the amount of direct sunlight the panel is receiving).
4. Use a wire nut or electrical tape to seal off any unused wires.
D. Using the crescent opening
on the Fan Mount Arm,
install the second 5/16”-18
1 inch serrated flange head
bolt and nut. Do not tighten
completely.