Fogco EC20 User manual





 ( K>O

 



EC20
MAX


EC20
MAX
15•
1intake vent
 










EC20
MAX
30'

'
30'
EC20
MAX
EC20
MAX




EC20
MAX
EC20
MAX
30' I


 
 Connect only to low voltage DC power supply. Not warranted for use over 45V DC
 WARNING: NO SERIES WIRING. Do NOT wire multiple fans in series to power supply.
 Only wire fans in parallel or directly to power supply. Wiring fans in series will void warranty
and may result in motor failure .
i!
[

rINPUT POWER 
 (GREEN)
Positive (BCK)
 
 

 

  

 
  
 
 
 
 
 
 
 
 
   
     

   
 

   
 
  

 
   



 

--&




 
















ADJUSTABLE MOUNT ASSEMBLY
Parts List
•1 ea T Bracket Plate
•1 ea T Bracket Post
•2 ea 1/4”-28 x 1.0” Flat Head Hex Drive Screws
•2 ea 1/4”-28 Locknuts
•2 ea 1/4” Washers
•1 ea section 1-1/4” square tube
•1 ea section 1” square tube
•4 ea Z Brackets
•6 ea 5/16"-18 x 2.0” Serrated Flange Head Bolts
•4 ea 5/16”-18 x 1.0" Serrated Flange Head Bolts*
•10 ea 5/16”-18 Serrated Flange Head Nuts*
Tools Needed
•3/8” socket or wrench for 1/4"-20 bolts
•7/16” socket or wrench for 1/4”-20 nuts
•1/2” sockets or wrenches for 5/16”-18 bolts and nuts
1. Select desired orientation of T Bracket
Post relative to T Bracket Plate and
attach using the supplied 1/4”-28
hardware. Flat head screws should sit
flush into the counter sunk holes of
choice on T Bracket Plate. Place washers
under locknut and tighten securely to
attach the T Bracket Post to Plate.
2. Attach two Z Brackets to one end of the
1” square tube and two Z Brackets to
one end of the 1-1/4” square tube so
that exposed ends come together to
form a narrow point as pictured at right.
Install Z Brackets so the oval hole
extends away from tube, and is free of
hardware. Use 5/16-18 x 2” serrated
flange head bolts and nuts to secure
each of the Z Bracket pairs to tube
sections.
3. Insert the T Bracket Post between the
narrow-exposed ends of the two Z
Brackets on the 1-1/4” tube and secure
the T Bracket Post using two 5/16-18 x
1” serrated flange head bolts and nuts.
*2 ea included on fan
1
2
3
4-5
4. Insert 1” tube inside 1-1/4” tube
to desired length. A minimum of 6”
insertion is required for stability
of the mount.
5. Secure the two tubes together using two 5/16-18 x 2”
serrated flange head bolts and nuts in two available holes going
through both tubes. Allow for at least one open hole in tube
between the 2” bolts for additional stability. Bolts should be
snug but do not over-tighten as that can distort the tube and
compromise adjustability.
6. Use T Bracket Plate to hang the complete mount assembly
from ceiling, beams or other appropriate overhead structure.
Mounting varies by application, additional user selected
hardware required.
7. Once mount assembly has been 7
securely hung, install EC20 Max
Snap-Fan’s motor clamp to the
narrow-exposed end of the lower
Z Bracket pair by inserting the Z
Brackets in between the two sides
of the motor clamp flange as pictured
at right. Secure motor clamp to lower
Z Brackets using two 5/16”-18 x 1”
serrated flange head bolts and nuts.
If necessary, loosen the 1/4”-20 x 1” bolts and nuts on fan’s
motor clamp slightly to allow room for insertion of Z Brackets
into motor clamp. Adjust fan to desired angle and tighten
hardware to secure fan in place.
8. Once the 5/16”-18 hardware has secured the fan’s motor
clamp to the lower Z Brackets, tighten the motor clamp’s inner
1/4”-20 bolts and nuts as they may become loose after
tightening motor clamp to fan mount.
SF.2380.KIT

SF.1358