foras Belmont Pebble Pool Luminar User manual

The Belmont Pebble Pool Luminar water feature is available in two sizes: 30cm or 40cm
ball. The kit can be used recessed into a flower bed or incorporated into a patio.
The kit contains: 65cm reservoir, pump 800 litres per
hour with 10m of cable, plug, 20mm water pipe,
Luminar nozzle, stone ball and a 25kg bag of pebbles.
Check the kit before installation.
2: Place the pump in the reservoir, then run the power cable up and over the lip of the reservoir and out to the
required power supply (this could be fed through an underground pipe that leads to the feature from a power
source). Fit the reservoir top in place leaving the inspection hatch off. Place the support ring on the reservoir.
Feed the 20mm water pipe down through the ring and down into the reservoir connecting to the outlet on the
pump. Place some packaging or a wooden block on the lip of the reservoir to protect it when moving the ball.
See diagram A.
Belmont Pebble Pool
Luminar Water Feature
Kit Instructions
Cont:-
Belmont Pebble Pool Luminar Water Feature Kit
The Pebble Pool can be installed above ground (with a
brick surround) or below ground as per our diagrams.
There are some important details that need to be
followed. Please read the instructions carefully before
installation, if you are unsure of any details please
contact local stockist or Foras team for further help.
1: Having installed the reservoir into the ground,
follow our step by step guide for installation.
A

6: Roll the ball up onto
the support ring, taking
care not to nip the pipe
(two people are needed to
place the 40cm ball).
Adjust the ball so the hole
is in the middle, this will
allowing the water to flow
evenly over the ball.
Cont:-
Note.
Ensure the ball is the
right way up with the
30mm recess hole at
the top see Diagram
Band Picture B1.
3 : First ensure that the ball is the correct way up with the
30mm recess hole at the top. See picture B1. Then roll the
ball up to the edge of the ring and secure in position so it
does not move.
5: Feed the water pipe up from the reservoir through the bottom of the
ball. Connect the water pipe to the luminar Nozzle.
4: Begin to feed the luminar plug and cable (shown in red) down through the ball, then down through the
support ring into the reservoir. Pull any slack down and store in reservoir, then run the luminar plug up and
over the lip of the reservoir and through underground pipe (if installed) to the required power supply. Leave
the luminar Nozzle a few inches from the ball recess. See Diagram B.
Picture B1. Ball
top
Cont:-
B

8: Cover the service hatch
with cover. Dress the
reservoir top with the bag of
pebbles.
11: Fill the reservoir with water and switch on the pump. The pump can
be adjusted to obtain the required flow rate by removing the service
hatch cover and adjusting the pump. In a windy location reducing the
flow rate will avoid the water blowing off the ball.
Foras cleaning kits are
available to help prevent algae
build up, and keep the stone
and water clean.
12: During the winter the pump should be switched off to protect from
frost and placed in an insulated bag then returned into the support pipe.
The ball should then be replaced ready for an easy start in the spring.
Visit our website or contact the Foras team for full details.
Installation Diagram
Foras, West Head Farm, Stowbridge, Kings Lynn, Norfolk, PE34 3NJ www.foras.co.uk email: [e-mail].
9: Connect the cables to
the plugs
For further help and support on Foras products call our office on 01366 381069
Important tips. WARNING!
Belmont balls are heavy. Take extra care when moving them.
Take care not to nip cable or water pipe when placing the ball on
ring.
7: Push excess pipe and
luminar nozzle down into
the ball recess.
Cont:-