Forging Mount FM4503 User manual

®
Instruction Manual
MAX
MAX
30
22LBS FM4503
Thank you for choosing our product! We strive to provide the best quality
and services for our customers. Would you kindly share your experience
on Amazon if you are satisfied? If you have any questions, please feel
free contact us.
Email：[email protected]
We’re ready to help!
Triple Monitor Desk Mount
mm
mm
SKU :

Safety Caution
-1-
•Carefully open the carton, remove contents and lay out on cardbard or other protective
surface to avoid damage.
•Check to assure that all components were received undamaged. Do not use damaged or
defective parts.lf you require replacement parts, contact customer service at
[email protected]
•Carefully read all instructions before attempting installation.
UNPACKING INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
•Install and operate this product with care. Please read this instruction before beginning the
installation, and carefully follow all instructions contained herein. Use proper tools during
installation.
•
If you do not understand the instructions or have any concerns or questions, please contact
customer service at
[email protected]
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment!
over resulting in death or serious injury!
This product contains small items that could be a choking hazard if swallowed.
Keep these items away from yong children
:
It is the installer’s responsibility to make sure the combined weight of FM4503 and the display
does not exceed 22 ibs(10kg).Use with heavier result in instability causing tip
Supplied parts
Wrench
Spacer
Allen key
Allen key
Allen key
Wire clip
Wire clip
6
7
D1
8 a D1
8 b
Grommet base plate
Clamp
Clamp Brace
Support Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
Swivel Arm
VESA Plate
Nut
Bolt
Bolt
Bolt
Bolt
monitor may
D
E
9
10
bottom pole
Top pole
Swivel head
3
3
12
12
12
2
F

2
ASSEMBLY STEPS
STEP 1A Install the Base(C Clamp Mount Option)
1. Install the clamp brace (5) to the bottom pole (9) using x3 M5x16 bolts (C). See Figure 1.
2. 8a) to the clamp brace (5) , see Figure 2.
3. Install the clamp (4) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 2 positions. Connect using x2 M8x12 bolts (B) and tighten using the
Allen key (K). Tighten the clamp to the desktop using the plastic knob. See Figure 3.
Figure 1
8a Figure 2
Figure 3
8a 1
9
9
bottom pole
clamp brace
9
top pole
clamp
Allen key
6mm
Allen key
3mm
connect the top pole to the bttom pole(screwing in),
then tighten the set screws in the middle of assembled
pole with Allen key M

3
ASSEMBLY STEPS
STEP 1B Install the Base( Grommet Mount Option)
Option B: Grommet Base with Existing Hole If existing grommet hole comes with a plastic protector, remove it to ensure a flat surface
before installing the desk mount.
1. Install grommet base plate ( 7) to the pole (1) using x3 M5x16 bolts ( C). See Figure 4.
2. 8b) to the grommet base plate (7) , see Figure 5.
3. Position pole (1) on the mounting sur fa ce and secure using the support plate ( 6),
15/64 in.(6mm)
1/8 in.(3mm)
6a
Remove part [a]
from part [4]
4a
Secure the mount
to the desktop
1
7
C
Figure 4 8b Figure 5
7
8b
6
a
M
1
C
K
Tighten the clamp to the desktop using the plastic knob(part a). See Figure 7.
Figure 6 Figure 7

4
STEP 2 Assemble Arms and wire clips
Install swivel arm (2) to the pole (1). Fasten the bolt with supplied Allen key (K). Attach the wire clip
( I , J ) to the pole (1) and swivel arm (2).
10
10
swivel head(10)
swivel head
swivel arm

STEP 3-1
OPTION A: Flat Back Monitor
Attach the VESA plate ( 3) to the monitor with
M4x12 bolts ( D).
NOTE: Hand tighten screws to avoid over
tightening.
OPTION B: Curved Back Monitor
Attach the VESA plate ( 3) to the monitor with M4x30
bolts (E) and M4 spacers ( F).
NOTE: Hand tighten screws to avoid over
tightening.
Attach the Monitor VESA Plate to the Monitors
Slide the monitor onto the head of swivel arm (2).
STEP 3-2
Install the security nut ( A). Make sure the security
nut is installed before you rotate the monitor. For
minor height adjustment, use Allen key (P).
5
D
E
D
D
D
DF
F
F
F
M4x30
M4x12
spacer
VESA plate
3
12
12
12
3
F
EE
EE

M
To level the monitors, remove the nut (A) and turn the bolt with the Allen key
M) to raise or lower the monitor. Replace nut (H
STEP 5 Adjustments
Tighten the bolt with the supplied Allen key (K) to fix the tilt angle.
K
Store Allen Keys into the Cable Clip
Step 6
K 15/64 in.(6mm)
M 1/8 in.(3mm)
Use the supplied Allen key set (L) to make any necessary adjustments for arms. Manage cables and store Allen
keys (O) in wire clip ( I) for future use.
L 3/16 in.(5mm)
K 15/64 in.(6mm)
M 1/8 in.(3mm)
L 3/16 in.(5mm)
for future use.
6