FORTNINE TINKER TOTTER User manual

(1)1.5“x12”steelpipe
(1)gatehingewith90degreestop
(3)cambuckletiedowns
(4)eyeboltscrews
(12)3”flatheaddeckscrews
(2)4”nails
(11)6”grkstructuralscrews
(1)10’x10mmrebar
(4)36“x1.5”slottedsteelangleiron
(2)4x6”x12’lumber
LISTOFMATERIALS
Step1:cutlumber(2)4x6”x12’
30” 30” 15.5” 15.5” 7.5”
84” 11.5”
surplusforf*ckupsor
increasingheight,length
45”
90˚
6” 3”
0.5”square
notch
forhinge
1.5”
1.5”
TOPDOWN
WHENASSEMBLED
6”
90˚
centered
1.25”

centered
4”
3.25”depth
Step2:drillholes1.5”Innerdiameter
“TINKERTOTTER”WORKSTAND
buildmanual!
WARNING:Buildandusethis
standatyourowndamnrisk
(thatmeansyoutoo,Americans!).
Forthesakeofliability,just
presumethestandwillfall
over(and/orapart)anddestroy
yourmotorcycle,yourself,
andeverythingelseyoumay
loveorvalue(ifany).

LAYDOWNANDTHENADD
ANDALIGNTHEHOLES.USEscrap
FORSUPPORT.ADDTHEREMAINING
ANDBLOCKSANDALIGNTHE
EDGES.


X
X-3”
3”
12”
Step3:REBARprep10’x10mmrebar
Step4:hingepreponward™permalign™hinge
RIGHTSIDE LEFTSIDE
FRONT
CROSSSECTION
Step5:assembly1.5”x12”STEELPIPE
placeandintopositionandscrew
inyourfirst5grk’s.besuretopre-drill
the4neartheedges,theymaysplitor
endupcrackingifthewooddriesout
overtime.

screwasinglegrkthroughandINTO
thebottomof,thenfliptherigover
andscrewinyourremaining5grksinto
and.

measureforX
andtake3”off
forclearance.
heatyourrebar
withatorchand
usethelength
forleverageto
benditundera
bootorinavice.
trimtheexcess
rebarwithan
anglegrinder
orhacksaw.
PinchyourOnward™Permalign™
hingeinavice,andtrimthe
tabsoffbelowtheholes.
thishelpsthehingeclearthe
groundwhileleavingenough
leftforsupportwhenthebike
ismounted.
DROPTHEPIPEINTOTHEHOLE.
ITSHOULDSTICKOUTNO
MORETHAN3INCHES.


[scrap]
[scrap]
(11)6”GRKDECKSCREWS(ORLAGBOLTS)

3”
(4)2”flatheadDECKSCREWS
rebar,(2)nails,(4)eyebolts.
RIGHTSIDE LEFTSIDE
Step6:hitchingstraps(3)cambuckletiedowns
attachthestraps
totheeyebolts
on
threaditthrough
theeyebolton



lineuptheendsofandandplace
theknuckleofthehingeintothenotch.

Thenscrewthetrimmedhingeintothe
woodthroughthefourholes.
Flatheadscrewssinkintotheholes
inthehinge,screwswitharaisedhead
maybumpintothetabs.
lineuptheendsofyourrebartriangle
ontothetopsofand,thendrill
down3incheswitha10mmbit.
youmayneedtohammertherebarinto
theholes.Securewithnails.
SCREWYOUREYEBOLTSINNEARTHETOPs
of
NOTE:Bewcarefulnottoscrewaneye
boltintothepipeorrebar!
to p
view
happywrenching!