Foxfury Lighting Solutions Tacswan EXOLANDER 700-XLS-II User manual

EXOLANDER©SYSTEMS
FOR AUTEL EVO II
700-XLS-II | 700-XPS-II | 700-XSS-II | 700-3AR-II | 700-XSPS-II
PRODUCT MANUAL

2
TABLE OF CONTENTS
EXOLANDER©Systems
3
EXOLANDER©Landing System
Reference Guide
Physical Characteristics
Installation
4
5
5-7
D100 Drone Spotlight©
Reference Guide
Physical Characteristics
Battery
Operational Modes
Installation
8
9
10
10
11-12
Manual Payload Delivery System©
Reference Guide
Physical Characteristics
Installation
Payload Delivery
Recommended Payload for Delivery
13
14
14-15
15
16
CARE/CLEANING
17
WARNINGS/WARRANTY
17-18
CONTACT FOXFURY
18

3
EXOLANDER©SYSTEMS
EVO II
Saddle
Mount©
EXOLANDER©
Landing
Skids
Manual
Payload
Delivery
System©
D100
Drone
Spotlight©
EXOLANDER©
Landing System
for EVO II
P/N 700-XLS-II
- - -
- - -
EXOLANDER©
Payload System
for EVO II
P/N 700-XPS-II
- - -
EXOLANDER©
Spotlight System
for EVO II
P/N 700-XSS-II
- - -
Autel
EXOLANDER©
System for
EVO II
P/N 700-3AR-II
- - -
EXOLANDER©
Spotlight &
Payload System
for EVO II
P/N 700-XSPS-II

4
EXOLANDER©LANDING SYSTEM
REFERENCE GUIDE
Locking Knob &
Screw (2 ea)
Payload Delivery
Mounting Slot
(4 ea)
External Accessory
Snap Lock Mount
(4 ea)
D100©Mounting
Hole (4 ea)
EXOLANDER©
Mount Connector to
Saddle Mount©(4 ea)
EXOLANDER©Landing
Foot with Slot (4 ea)
LANDING SKIDS*
Tab (4 ea)
per Skid
EXOLANDER©HALF
EVO II SADDLE MOUNT©
Snap Lock (7 ea)
Alignment Pin
( 2 ea)
Alignment
Slot
Threaded Locking
Nut Insert
Locking Knob
& Screw
EXOLANDER©ASSEMBLED
*Not included in P/N 700-3AR-II

5
PHYSICAL CHARACTERISTICS
DIMENSIONS
WEIGHT*
EVO II Saddle Mount©
2.52 x 3.4 x 3.5 in
(64 x 86 x 89 mm)
1.0 oz (28.3 g)
EXOLANDER©,
assembled
6.7 x 6.5 x 4.7 in
(170 x 165 x 120 mm)
4.05 oz (114.7 g)
Landing Skid
8.66 x 0.96 x 0.6 in
(220 x 24.3 x 15 mm)
0.45 oz (12.8 g)
per skid
*Total Weight is 5.95 oz (168.6 g).
EXOLANDER©LANDING SYSTEM
INSTALLATION
❶Install Saddle Mount©on EVO II.
1. Slide the Saddle Mount©on EVO II and make sure that the two
extensions fit behind the front arms of the EVO II and press down.
WHAT'S INCLUDED
EVO II Saddle Mount©
EXOLANDER©
Landing Skid (set of 2)*
*Not included in P/N 700-3AR-II
WARNING
It is the responsibility of drone/UAV users to follow the FAA and global laws and
regulations
and/or the laws and regulations applicable to the flight location.

6
❷Install EXOLANDER©on Saddle Mount©.
1. Place EVO II with Saddle Mount©upside down on a flat surface.
2. Align the EXOLANDER©Half with Snap Lock locations on Saddle
Mount©and slide in the EXOLANDER©Half at an angle as shown
below. Make sure the foot is facing away from the center of the
drone. Tilt the EXOLANDER©Half as shown.
3. Install the other EXOLANDER©Half in the open Saddle Snap Lock
locations. Bring the units together and align the Pin into the Hole on
each side.
4. Align Locking Knob & Screw and Thread Locking Nut Insert on each
side.

7
5. Tighten each screw until the units are mated.
6. The EXOLANDER©installation is now complete.
7. To install the Landing Skid, align each Tab on Landing Skid with each
Slot on the EXOLANDER©Landing Foot. Press and snap Landing Skid
on.
WARNING:
Manually test the EXOLANDER©Landing System by wiggling it and making
sure nothing is loose. Note that a small amount of movement between the
structure and the UAV has been created, at the request of AUTEL, to
eliminate adding unnecessary forces to the vehicle’s structure.

8
D100 DRONE SPOTLIGHT©
REFERENCE GUIDE
Power/Mode Switch
¼-20 Threaded Hole
(2 ea)
Mounting Knob (2 ea)
D100 Drone Spotlight©
Back View
Battery Cover

9
WHAT'S INCLUDED
D100 Drone Spotlight©
Mounting Knob (2 ea)
18650 Lithium-Ion Battery (2 ea)
XTAR Battery Charger
PHYSICAL CHARACTERISTICS
DIMENSIONS
3.46 x 2.03 x 2.46 in (88 x 51.5 x 62.5 mm)
WEIGHT
8.92 oz (253 g)
12.23 oz (346.6 g) with provided 18650 batteries
WARNINGS
Please fully charge the provided 18650 batteries before using the D100©for the
first time.
Do not stare into the LEDs for long periods of time or from close range (less than
2 ft / 0.6 m)
While using any FoxFury product, please operate at safe speeds.
It is the responsibility of drone/UAV users to follow the FAA and global laws and
regulations
and/or the laws and regulations applicable to the flight location.
The D100©will become hot to touch after 20 min of continuous use. Please handle
carefully by avoiding contact with the metal heatsink.

10
BATTERY
D100©requires two (2) 18650 batteries.
Mixing of new and used, or different brand batteries, is not
recommended as this could lead to leakage or explosion.
BATTERY INSTALLATION AND REPLACEMENT
❶Slide the battery cover open and insert the battery according to the plus
(+) and minus (-) symbol located inside of the battery compartment.
❷Once batteries are installed, test the light’s performance by activating the
Power/Mode Switch. Slide the battery cover back on.
CHARGING BATTERY
Refer to the instruction manual provided with the XTAR Battery Charger.
OPERATIONAL MODES
OPERATIONAL MODES
Press and hold Power/Mode Button to turn the light ON.
Press Power/Mode Button again to change the mode to STROBE.
Press Power/Mode Button again to turn the light OFF.
MODE
LUMENS
BATTERY LIFE
ON
2,300
70 minutes
TURBO-
STROBE
2,300
140 minutes
Power/Mode
Switch

11
D100©INSTALLATION
ITEMS REQUIRED:
EXOLANDER© Landing System
❶Install EXOLANDER©Landing System on EVO II. Reference p.5 - 7.
❷Install D100©on EXOLANDER©Landing System.
1. Insert each Mounting Knob in the D100©Mounting Hole of the
forward-facing section of EXOLANDER©.
2. Align the Mounting Knobs with the ¼-20 threaded screw holes on
D100© to install D100©on EXOLANDER©. Make sure the switch cover
faces the right side (facing the unit). Note that the curved rear edge
should be on the top.
Mounting Knob
Mounting Knob

12
3. Tilt D100©to access the Switch and turn it on to desired mode.
4. Adjust the tilt of D100©to desired angle and tighten the Mounting
Knobs.
Power/Mode
Switch

13
MANUAL PAYLOAD DELIVERY
SYSTEM©REFERENCE GUIDE
WHAT'S INCLUDED
Payload Delivery Unit with Cross Bar
Handle/Cord Reel with 550 Paracord (20 ft / 6.1 m)
1/4 x 1½ QR Pin with Ring
Key Ring (38 mm diameter)
Carabiner with Ring
Payload Delivery Bag
Payload
Delivery Bag
Payload Delivery Unit
with Cross Bar
Carabiner
with Ring
Handle/Cord Reel
with 550 Paracord
Key Ring
(38 mm Diameter)
¼ x 1½ QR Pin
with Ring

14
PHYSICAL CHARACTERISTICS
WEIGHT
6.92 oz (196.3 g) - fully assembled
3.56 oz (101 g) –without bag
MANUAL PAYLOAD DELIVERY
SYSTEM©INSTALLATION
ITEMS REQUIRED:
Saddle Mount©for EVO II
EXOLANDER© Landing System
❶Install EXOLANDER©Landing System on EVO II. Reference p.5 - 7.
❷Install Key Ring (38 mm Diameter) and 1/4 x 1½ QR Pin with Ring on the
Payload Delivery Unit with Cross Bar if not already installed.
WARNINGS
While using any FoxFury product, please operate at safe speeds.
It is the responsibility of drone/UAV users to follow the FAA and global laws and
regulations
and/or the laws and regulations applicable to the flight location.
If delivering with D100©installed, maximum payload is 14.1 oz (400 g).
If delivering without the D100©installed, maximum payload is 28.2 oz (800 g).

15
❸Install Payload Delivery Unit with Cross Bar on the rear of EXOLANDER©.
1. Locate Payload Delivery Mounting Slots on the rear of
EXOLANDER©.
2. Align the Cross Bar on the top hole of the Payload Delivery Mounting
Slot and slide it down to lock in place.
PAYLOAD DELIVERY
Insert the payload inside the Payload Delivery Bag.
Place the bag with payload behind EVO II, about 24 in (61 cm) away.
Unwind the Paracord and fly EVO II.
To release payload, simply pull on the Handle with a force of 2 - 4 lbs
(0.9 - 1.8 kg). Note that this effort will translate into minimal movement
on the EVO II.
Payload Delivery
Mounting Slot

16
RECOMMENDED PAYLOAD
FOR DELIVERY
EXOLANDER©Landing System: 0.37 lbs (168.6 g)
D100©: 0.76 lbs (346.6 g)
Manual Payload Delivery System©: 0.43 lbs (196.3 g)
Below is the recommended payload for delivery based on reported
measurements by professional users.
Configuration
Total Payload & Flight Time
EXOLANDER©
No Limitations
EXOLANDER©+ 2 D3060 Lights
No Limitations
EXOLANDER©+ D100
No Limitations
EXOLANDER©+ D100
+ 2 D3060 lights
No Limitations
EXOLANDER©+ Manual Payload
Delivery System©w/o No Bag
1.0 lb (454 g) | No Time Limitation
Ambient temperature dependent; keep
an eye on battery temperature*
EXOLANDER©+ Manual Payload
Delivery System© with Bag
0.7 lbs (317.5 g) | 15 Minutes Max
Ambient temperature dependent; keep
an eye on battery temperature*
EXOLANDER©+ D100©+ Manual
Payload Delivery System©
0.5 - 0.7 lbs (227 –317.5 g) |
5 - 7 Minutes Max
Ambient temperature dependent; keep
an eye on battery temperature*
EXOLANDER©+ 2 D3060 lights +
Manual Payload Delivery System©
0.1 lb (45.4 g) | 12-15 Minutes Max
Ambient temperature dependent; keep
an eye on battery temperature*
* Keep the payload at a maximum of 3 ft (91 cm) below the aircraft and keep monitoring the battery
temperature.

17
WARRANTY AND OTHER
INFORMATION
PRODUCT DURABILITY
CARE/CLEANING
Your FoxFury product is a professional
tool. Regular maintenance and care of
your light will maximize performance for
you. As needed, clean your FoxFury
product using a soft washcloth. Do not
immerse.
ACCESSORIES
Rechargeable 18650 Li-Ion
Battery (P/N 70-18650T)
Battery Charger (P/N 600-155)
WARNINGS
FoxFury, LLC is not responsible for the
incorrect use of any FoxFury Lighting
product.
When used for extended periods
of time the D100©will become
HOT to the touch. Please use care
when operating.
Lights are strong enough to cause
damage to the human eye.
Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft / 0.6 m).
FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.
Usage of this product must be
supervised by an adult when it is
being used by a minor.
Any FoxFury product should be
operated at speeds safe enough
to maneuver around surrounding
obstacles.
Do not use under the influence of
drugs or alcohol.
ONE YEAR WARRANTY
FoxFury, LLC (“FoxFury”) warrants
this product to be free from defects
in material for one year after
purchase. Li-Ion batteries have a one
year pro-rated or 500 re-charge cycle
pro-rated warranty, whichever the
user reaches first.
This warranty is given only to the
original end user of the accompanying
product. If you purchased a product
from someone other than an
authorized FoxFury reseller/distributor
or if the product was used, (including
but not limited to demo models, show
models or refurbished product by
someone other than FoxFury) prior to
your purchase, you are not the
Original Purchaser and the product
that you purchased is not covered by
this warranty. This warranty is VOID
if this Product has been altered or
modified in any way (including but not
limited to attempted warranty repair
without authorization from FoxFury
and/or alteration/removal of the serial
number). To expedite warranty
concerns, we encourage the end user
to register their FoxFury Product at
3M

18
www.foxfury.com/pages/warrantyregi
stration.
THIS IS THE ONLY WARRANTY,
EXPRESSED OR IMPLIED,
INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES ARE
EXPRESSLY DISCLAIMED
EXCEPT WHERE SUCH
LIMITATION IS PROHIBITED BY
LAW.
You may have other specific legal
rights which vary by jurisdiction. Go
to www.foxfury.com/pages/warranty
for a complete copy of the warranty.
Retain your receipt for proof of
purchase.
CONTACT FOXFURY
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: FoxFury.com
All FoxFury products are designed in
Oceanside, CA. All FoxFury
products are manufactured with the
highest quality USA and foreign
parts. Products are assembled in
either FoxFury’s controlled plant in
Asia or the USA, under strict quality
control.
CALIFORNIA PROPOSITION
65
This product can expose you to
chemicals including Lead and DEHP,
which are known to the State of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65Warnings.ca.gov.

08/2021